Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2018.01
RM30M0E _54 Brake _017098 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0256246 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1232  Acceleration Sensor Stuck Malfunction  C1243  Acceleration Sensor Stuck Malfunction  C1245  Acceleration Sensor Output Malfunction  C1279  Acceleration Sensor Output Voltage Malfunction (Test Mode DTC)  C1473  Yaw Rate Sensor (Test Mode DTC)  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the yaw rate and acceleration sensor (airbag ECU assembly) via the CAN communication system.

The airbag ECU assembly has a built-in yaw rate and acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2).

If there is trouble in the bus lines between the yaw rate and acceleration sensor (airbag ECU assembly) and the CAN communication system, the DTC U0124 (malfunction in CAN communication with the acceleration sensor) is output.

These DTCs are also output when calibration has not been completed.

DTCs C1279 and C1473 can be cleared when the yaw rate and acceleration sensor (airbag ECU assembly) sends a yaw rate and/or deceleration signal or the Test Mode ends. DTCs C1279 and C1473 are output only in the Test Mode.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1232 Acceleration Sensor Stuck Malfunction At a vehicle speed of 10 km/h (6 mph) or more, either GL1 or GL2 (input signal) does not change for 30 seconds or more.
·

Yaw rate and acceleration sensor (Airbag ECU assembly)

·

Yaw rate and acceleration sensor (Airbag ECU assembly) circuit

·

Sensor installation


C1243 Acceleration Sensor Stuck Malfunction While the vehicle speed changes from 30 km/h (19 mph) to 0 km/h (0 mph), the condition that the values of GL1 and GL2 do not change 0.0294 G or more occurs 16 times or more.
·

Yaw rate and acceleration sensor (Airbag ECU assembly)

·

Yaw rate and acceleration sensor (Airbag ECU assembly) circuit

·

Sensor installation


C1245 Acceleration Sensor Output Malfunction At a vehicle speed of 30 km/h (19 mph) or more, the difference between the forward and backward G calculated from the acceleration sensor value and that calculated from the vehicle speed exceeds 0.35 G for 60 seconds or more.
·

Yaw rate and acceleration sensor (Airbag ECU assembly)

·

Yaw rate and acceleration sensor (Airbag ECU assembly) circuit

·

Sensor installation


C1279 Acceleration Sensor Output Voltage Malfunction (Test Mode DTC) Detected only during Test Mode.
·

Yaw rate and acceleration sensor (Airbag ECU assembly)

·

Sensor installation


C1473 Yaw Rate Sensor (Test Mode DTC) Detected only during Test Mode. Yaw rate and acceleration sensor (airbag ECU assembly)

WIRING DIAGRAM

C375654E05
0.823,0.823 1.438,1.021 0.615,0.198 10 false CANH 0.844,1.458 1.458,1.656 0.615,0.198 10 false CANL 0.979,2.063 1.438,2.26 0.458,0.198 10 false IG2 1.031,2.688 1.344,2.885 0.313,0.198 10 false E1 1.031,3.292 1.344,3.49 0.313,0.198 10 false E2 0.083,4.167 0.542,4.365 0.458,0.198 10 false F21 0.073,4.344 2.219,4.74 2.146,0.396 10 false Yaw Rate and Acceleration Sensor (Airbag ECU Assembly) 0.646,5.375 2.396,5.646 1.75,0.271 10 false : CAN Communication Line 2.188,2.219 3.563,2.417 1.375,0.198 10 false A/BAG-IG2 4.375,2.042 5.781,2.49 1.406,0.448 10 false from Ignition or Starter Switch Assembly*3 4.375,2.854 6.823,3.052 2.448,0.198 10 false from IG2 Relay*4 5.406,0.823 5.865,1.021 0.458,0.198 10 false A48 5.406,1.438 5.865,1.635 0.458,0.198 10 false A48 5.74,0.823 6.198,1.021 0.458,0.198 10 false A49 5.729,1.448 6.188,1.646 0.458,0.198 10 false A49 5.448,0.646 5.76,0.844 0.313,0.198 10 false 25 5.76,0.635 6.073,0.833 0.313,0.198 10 false 25 5.448,1.25 5.76,1.448 0.313,0.198 10 false 14 5.76,1.26 6.073,1.458 0.313,0.198 10 false 14 5.448,1.01 5.76,1.208 0.313,0.198 10 false *1 5.448,1.646 5.76,1.844 0.313,0.198 10 false *1 5.75,1.021 6.063,1.219 0.313,0.198 10 false *2 5.771,1.646 6.083,1.844 0.313,0.198 10 false *2 6.073,0.823 6.688,1.021 0.615,0.198 10 false CANH 6.063,1.448 6.677,1.646 0.615,0.198 10 false CANL 5.594,4.177 7.146,4.615 1.552,0.438 10 false Skid Control ECU (Brake Actuator Assembly) 3.042,3.656 5.115,4.042 2.073,0.385 10 false *1: except LHD with Continuously Variable Transaxle 3.042,4.354 4.865,4.719 1.823,0.365 10 false *2: for LHD with Continuously Variable Transaxle 3.042,5.073 5.458,5.333 2.417,0.26 10 false *3: w/o Smart Entry and Start System 3.052,5.448 5.458,5.708 2.406,0.26 10 false *4: w/ Smart Entry and Start System 1.323,0.656 1.635,0.854 0.313,0.198 10 false 13 1.333,1.271 1.646,1.469 0.313,0.198 10 false 22 1.313,1.948 1.625,2.146 0.313,0.198 10 false 21 1.313,2.563 1.625,2.76 0.313,0.198 10 false 25 1.313,3.177 1.625,3.375 0.313,0.198 10 false 26

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

When replacing the yaw rate and acceleration sensor (airbag ECU assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION



HINT:

When U0124 and/or U0126 is output together with C1232, C1243 and/or C1245, inspect and repair the trouble areas indicated by U0124 and/or U0126 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>U0073


PROCEDURE

1.CHECK DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

At a speed of 30 km/h (19 mph) or more, drive the vehicle, turn the steering wheel, and decelerate (depress the brake pedal) the vehicle.


e.

Check that no CAN communication system DTC is output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


f.

Check if DTCs for zero point calibration of the yaw rate sensor undone (C1210) or for zero point calibration of the acceleration sensor undone (C1336) are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC (relating to yaw rate and acceleration sensor) is output A
DTC (relating to CAN communication system) is output B
DTC (C1210 and/or C1336) are output C




A

2.CHECK AIRBAG ECU ASSEMBLY INSTALLATION

B

C

2.CHECK AIRBAG ECU ASSEMBLY INSTALLATION
a.

Turn the ignition switch off.


b.

Check that the airbag ECU assembly has been installed properly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION

OK:

The sensor should be tightened to the specified torque.

The sensor should not be tilted position.



Result:
Proceed to
OK
NG



OK

NG