Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2018.01
RM30M0E _54 Brake _017098 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0256246 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1241  Low Power Supply Voltage Malfunction  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU (brake actuator assembly) stores this DTC and the fail-safe function prohibits ABS operation.

This DTC is stored when the IG1 terminal voltage deviates from the DTC detection condition due to a malfunction in the power supply or charging circuit such as the battery or generator circuit, etc.

The DTC is canceled when the IG1 terminal voltage returns to normal.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1241 Low Power Supply Voltage Malfunction When any of the following is detected:
1.

At a vehicle speed of 3 km/h (2 mph) or more, the IG1 terminal voltage is less than 9.5 V for 10 seconds or more.

2.

When the solenoid relay remains on and the IG1 terminal voltage is less than 9.5 V, the relay contact is open for 0.22 seconds or more.

3.

With the IG1 terminal voltage 9.5 V or less, the vehicle speed sensor power supply decreases for 60 seconds or more.

4.

When the motor fail safe relay is on, after the motor relay turns on, the IG1 terminal voltage is 9.5 V or less and the actuator pump drive motor is off for 0.22 seconds or more.


·

IG1 NO. 2 fuse

·

Battery

·

Charging system

·

Wire harness or connector

·

Skid control ECU (Brake actuator assembly)



WIRING DIAGRAM

C375655E04
0.938,0.729 2.365,1.156 1.427,0.427 10 false from Ignition or Starter Switch Assembly*3 1.208,1.604 3.656,1.802 2.448,0.198 10 false from IG1 Relay*4 3.573,0.896 4.948,1.094 1.375,0.198 10 false IG1 NO. 2 5.052,0.729 5.51,0.927 0.458,0.198 10 false A48 5.042,2.177 5.5,2.375 0.458,0.198 10 false A48 5.365,0.719 5.823,0.917 0.458,0.198 10 false A49 5.365,2.177 5.823,2.375 0.458,0.198 10 false A49 5.073,0.542 5.385,0.74 0.313,0.198 10 false 34 5.396,0.542 5.708,0.74 0.313,0.198 10 false 34 5.083,0.917 5.396,1.115 0.313,0.198 10 false *1 5.094,2.385 5.406,2.583 0.313,0.198 10 false *1 5.396,0.917 5.708,1.115 0.313,0.198 10 false *2 5.417,2.396 5.729,2.594 0.313,0.198 10 false *2 5.104,1.99 5.26,2.188 0.156,0.198 10 false 1 5.427,1.979 5.583,2.177 0.156,0.198 10 false 1 5.729,0.75 6.188,0.948 0.458,0.198 10 false IG1 5.698,2.188 6.313,2.385 0.615,0.198 10 false GND1 5.427,2.698 6.99,3.115 1.563,0.417 10 false Skid Control ECU (Brake Actuator Assembly) 0.042,2.219 3.708,2.417 3.667,0.198 10 false *1: except LHD with Continuously Variable Transaxle 0.063,2.625 3.406,2.833 3.344,0.208 10 false *2: for LHD with Continuously Variable Transaxle 0.073,3.021 2.5,3.271 2.427,0.25 10 false *3: w/o Smart Entry and Start System 0.094,3.427 2.396,3.708 2.302,0.281 10 false *4: w/ Smart Entry and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V


Result:
Result Proceed to
OK A
NG (for 1NR-FE) B
NG (for 2NR-FE) C




A

2.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

B

C

2.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness in the locking part and connecting part of the connectors.


c.
C349101C30
1.448,2.417 1.948,2.667 0.5,0.25 1.448,0.396 1.948,0.646 0.5,0.25 2.5,2.167 2.104,1.615 true 2.5,4.188 2.104,3.635 true 0.333,0.25 0.813,0.573 0.479,0.323 12 false *A 0.333,2.333 0.896,2.573 0.563,0.24 12 false *B 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 1.583,0.427 1.979,0.667 0.396,0.24 10 false A48 1.583,2.448 1.979,2.688 0.396,0.24 10 false A49 2.438,2.188 2.833,2.427 0.396,0.24 10 false IG1 2.438,4.208 2.833,4.448 0.396,0.24 10 false IG1
*A except LHD with Continuously Variable Transaxle
*B for LHD with Continuously Variable Transaxle
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Disconnect the skid control ECU (brake actuator assembly) connector.


d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
except LHD with Continuously Variable Transaxle
Tester Connection Switch Condition Specified Condition
A48-34 (IG1) - Body ground Ignition switch ON 11 to 14 V

for LHD with Continuously Variable Transaxle
Tester Connection Switch Condition Specified Condition
A49-34 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.

Turn the ignition switch off.


b.
C349101C31
1.448,2.417 1.948,2.667 0.5,0.25 1.448,0.396 1.948,0.646 0.5,0.25 0.5,1.875 1.042,1.333 true 0.5,3.875 1.042,3.333 true 0.333,0.25 0.813,0.573 0.479,0.323 12 false *A 0.333,2.333 0.896,2.573 0.563,0.24 12 false *B 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 1.583,0.427 1.979,0.667 0.396,0.24 10 false A48 1.583,2.448 1.979,2.688 0.396,0.24 10 false A49 0.083,1.792 0.479,2.031 0.396,0.24 10 false GND1 0.083,3.792 0.479,4.031 0.396,0.24 10 false GND1
*A except LHD with Continuously Variable Transaxle
*B for LHD with Continuously Variable Transaxle
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
except LHD with Continuously Variable Transaxle
Tester Connection Condition Specified Condition
A48-1 (GND1) - Body ground Always Below 1 Ω

for LHD with Continuously Variable Transaxle
Tester Connection Condition Specified Condition
A49-1 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

4.RECONFIRM DTC
a.

Reconnect the A48*1 or A49*2 skid control ECU (brake actuator assembly) connector.

*1: except LHD with Continuously Variable Transaxle

*2: for LHD with Continuously Variable Transaxle



b.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.


f.

Check if the same DTC is recorded.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Result Proceed to
DTC is not output A
DTC is output B



A

B