Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2018.01
RM30M0E _54 Brake _017098 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0256246 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1425  Open in Stop Light Switch Circuit  


DESCRIPTION

The skid control ECU (brake actuator assembly) detects the brake operating conditions through a signal transmitted by the stop light switch.

The skid control ECU incorporates a circuit to detect an open circuit. This DTC is output when an open circuit is detected in the stop light signal input line.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1425 Open in Stop Light Switch Circuit When IG1 terminal voltage is between 9.5 and 17.4 V, an open stop light switch circuit (A to B, A to body ground) continues for 3 seconds or more.
·

Wire harness or connector

·

Skid control ECU (Brake actuator assembly)



WIRING DIAGRAM

C375657E05
3.729,0.906 3.979,1.104 0.25,0.198 5.052,1.521 5.302,1.719 0.25,0.198 0.146,0.156 4.729,0.396 4.583,0.24 12 false for Bulb Type Stop Light: 0.26,1.104 2.094,1.302 1.833,0.198 10 false from Battery 1.448,1.281 2.063,1.479 0.615,0.198 10 false STOP 1.927,1.469 2.385,1.667 0.458,0.198 10 false A21 1.917,1.615 5.896,1.813 3.979,0.198 10 false Stop Light Switch Assembly 2.104,0.99 2.26,1.188 0.156,0.198 10 false 2 2.323,0.99 2.479,1.188 0.156,0.198 10 false B 2.958,0.99 3.115,1.188 0.156,0.198 10 false L 3.177,0.979 3.333,1.177 0.156,0.198 10 false 1 3.802,0.938 3.958,1.135 0.156,0.198 10 false A 5.125,1.542 5.281,1.74 0.156,0.198 10 false B 4.833,0.917 4.99,1.115 0.156,0.198 10 false 2 5.146,0.917 5.302,1.115 0.156,0.198 10 false 2 4.76,1.115 5.219,1.313 0.458,0.198 10 false A48 5.073,1.115 5.531,1.313 0.458,0.198 10 false A49 4.813,1.323 5.125,1.521 0.313,0.198 10 false *1 5.115,1.323 5.427,1.521 0.313,0.198 10 false *2 5.406,0.979 5.865,1.177 0.458,0.198 10 false STP 5.792,0.958 6.792,1.323 1,0.365 10 false Open Detection Circuit 5.438,2.896 6.99,3.281 1.552,0.385 10 false Skid Control ECU (Brake Actuator Assembly) 2.073,2.427 5.281,2.625 3.208,0.198 10 false to Stop Light Circuit 0.146,2.958 3.813,3.156 3.667,0.198 10 false *1: except LHD with Continuously Variable Transaxle 0.156,3.313 3.417,3.521 3.26,0.208 10 false *2: for LHD with Continuously Variable Transaxle

C375658E05
5.073,1.51 5.323,1.76 0.25,0.25 3.906,0.833 4.156,1.083 0.25,0.25 0.167,0.094 4.573,0.333 4.406,0.24 12 false for LED Type Stop Light: 0.052,1.094 1.885,1.292 1.833,0.198 10 false from Battery 1.552,1.24 2.219,1.438 0.667,0.198 10 false STOP 2.448,1.469 3.115,1.667 0.667,0.198 10 false GND 2.448,1.094 2.635,1.313 0.188,0.219 10 false B 2.823,1.094 3.281,1.292 0.458,0.198 10 false OUT 2.219,1 2.406,1.219 0.188,0.219 10 false 1 2.219,1.375 2.406,1.594 0.188,0.219 10 false 3 3.26,1 3.448,1.219 0.188,0.219 10 false 2 1.885,1.74 2.552,1.938 0.667,0.198 10 false A58 1.896,1.906 3.75,2.208 1.854,0.302 10 false Stop Light Switch Assembly 2.219,2.406 4.073,2.708 1.854,0.302 10 false to Stop Light Circuit 0.167,3.083 3.469,3.427 3.302,0.344 10 false *1: except LHD with Continuously Variable Transaxle 0.167,3.417 3.677,3.719 3.51,0.302 10 false *2: for LHD with Continuously Variable Transaxle 4.75,1.104 5.208,1.302 0.458,0.198 10 false A48 5.073,1.104 5.531,1.302 0.458,0.198 10 false A49 4.833,0.917 5.292,1.115 0.458,0.198 10 false 2 5.156,0.917 5.615,1.115 0.458,0.198 10 false 2 4.802,1.292 5.26,1.49 0.458,0.198 10 false *1 5.125,1.292 5.583,1.49 0.458,0.198 10 false *2 5.417,1 5.875,1.198 0.458,0.198 10 false STP 5.823,0.917 6.844,1.333 1.021,0.417 10 false Open Detection Circuit 3.99,0.875 4.448,1.073 0.458,0.198 10 false A 5.156,1.552 5.615,1.75 0.458,0.198 10 false B 5.458,2.844 7.042,3.292 1.583,0.448 10 false Skid Control ECU (Brake Actuator Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that all the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed On
Brake pedal released Off


Result:
Proceed to
OK
NG




OK

2.READ VALUE USING GTS (STOP LIGHT SW)

NG

2.READ VALUE USING GTS (STOP LIGHT SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly ON or OFF OFF: Brake pedal released
ON: Brake pedal depressed
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Stop Light SW
50003 105 37

d.

Check that the stop light switch assembly condition observed on the GTS changes according to brake pedal operation.

OK:

The GTS displays ON or OFF according to brake pedal operation.



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

4.CHECK TERMINAL VOLTAGE (STP TERMINAL)
3.RECONFIRM DTC
a.

Turn the ignition switch off.



Chassis > ABS/VSC/TRC > Clear DTCs
50002 105
c.

Turn the ignition switch off.


d.

Start the engine.


e.

Depress the brake pedal several times to test the stop light circuit.



Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE


Result:
Result Proceed to
DTC is not output A
DTC is output B



A

B

4.CHECK TERMINAL VOLTAGE (STP TERMINAL)
a.
C349101C35
1.448,2.417 1.948,2.667 0.5,0.25 1.448,0.396 1.948,0.646 0.5,0.25 0.5,3.51 1.313,3.344 true 0.5,1.49 1.313,1.323 true 0.333,0.25 0.813,0.573 0.479,0.323 12 false *A 0.333,2.333 0.896,2.573 0.563,0.24 12 false *B 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 1.583,0.427 1.979,0.667 0.396,0.24 10 false A48 1.583,2.448 1.979,2.688 0.396,0.24 10 false A49 0.177,1.406 0.573,1.646 0.396,0.24 10 false STP 0.177,3.417 0.573,3.656 0.396,0.24 10 false STP
*A except LHD with Continuously Variable Transaxle
*B for LHD with Continuously Variable Transaxle
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
except LHD with Continuously Variable Transaxle
Tester Connection Switch Condition Specified Condition
A48-2 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 8 to 14 V
A48-2 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V

for LHD with Continuously Variable Transaxle
Tester Connection Switch Condition Specified Condition
A49-2 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 8 to 14 V
A49-2 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT CIRCUIT)