Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2018.01
RM30M0E _54 Brake _017098 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0256246 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  Slip Indicator Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

The slip indicator light blinks during VSC and/or TRC operation.

If a malfunction is detected, the slip indicator light comes on to warn the driver.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DIAGNOSIS SYSTEM

WIRING DIAGRAM

C375660E07
0.146,2.865 4.125,3.063 3.979,0.198 10 false Combination Meter Assembly 0.698,4.271 4.365,4.469 3.667,0.198 10 false : CAN Communication Line 2.052,1.302 3.479,1.823 1.427,0.521 10 false from Ignition or Starter Switch Assembly*3 2.323,2.146 4.771,2.344 2.448,0.198 10 false from IG1 Relay*4 4.135,1.49 5.51,1.688 1.375,0.198 10 false IG1 NO. 2 4.906,1.302 5.365,1.5 0.458,0.198 10 false A48 4.917,2.344 5.375,2.542 0.458,0.198 10 false A48 5.229,1.302 5.688,1.5 0.458,0.198 10 false A49 5.219,2.333 5.677,2.531 0.458,0.198 10 false A49 4.938,1.115 5.25,1.313 0.313,0.198 10 false 34 5.281,1.104 5.594,1.302 0.313,0.198 10 false 34 4.958,1.49 5.271,1.688 0.313,0.198 10 false *1 4.958,2.531 5.271,2.729 0.313,0.198 10 false *1 5.281,1.5 5.594,1.698 0.313,0.198 10 false *2 5.302,2.531 5.615,2.729 0.313,0.198 10 false *2 4.969,2.146 5.125,2.344 0.156,0.198 10 false 1 5.302,2.146 5.458,2.344 0.156,0.198 10 false 1 5.594,1.292 6.052,1.49 0.458,0.198 10 false IG1 5.563,2.344 6.177,2.542 0.615,0.198 10 false GND1 5.448,2.875 6.99,3.406 1.542,0.531 10 false Skid Control ECU (Brake Actuator Assembly) 2.406,3.354 4.469,3.76 2.063,0.406 10 false *1: except LHD with Continuously Variable Transaxle 2.417,4.073 4.729,4.469 2.313,0.396 10 false *2: for LHD with Continuously Variable Transaxle 4.771,3.823 7.156,4.177 2.385,0.354 10 false *3: w/o Smart Entry and Start System 4.792,4.323 7.063,4.656 2.271,0.333 10 false *4: w/ Smart Entry and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTC is not output A
DTC is output B



A

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.CHECK BATTERY

NG

CONNECT CONNECTOR TO ECU CORRECTLY

3.CHECK BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V


Result:
Result Proceed to
OK A
NG (for 1NR-FE) B
NG (for 2NR-FE) C




A

4.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

B

C

4.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.
C349101C30
1.448,2.417 1.948,2.667 0.5,0.25 1.448,0.396 1.948,0.646 0.5,0.25 2.5,2.167 2.104,1.615 true 2.5,4.188 2.104,3.635 true 0.333,0.25 0.813,0.573 0.479,0.323 12 false *A 0.333,2.333 0.896,2.573 0.563,0.24 12 false *B 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 1.583,0.427 1.979,0.667 0.396,0.24 10 false A48 1.583,2.448 1.979,2.688 0.396,0.24 10 false A49 2.438,2.188 2.833,2.427 0.396,0.24 10 false IG1 2.438,4.208 2.833,4.448 0.396,0.24 10 false IG1
*A except LHD with Continuously Variable Transaxle
*B for LHD with Continuously Variable Transaxle
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Disconnect the skid control ECU (brake actuator assembly) connector.


d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
except LHD with Continuously Variable Transaxle
Tester Connection Switch Condition Specified Condition
A48-34 (IG1) - Body ground Ignition switch ON 11 to 14 V

for LHD with Continuously Variable Transaxle
Tester Connection Switch Condition Specified Condition
A49-34 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.

Turn the ignition switch off.


b.
C349101C31
1.448,2.417 1.948,2.667 0.5,0.25 1.448,0.396 1.948,0.646 0.5,0.25 0.5,1.875 1.042,1.333 true 0.5,3.875 1.042,3.333 true 0.333,0.25 0.813,0.573 0.479,0.323 12 false *A 0.333,2.333 0.896,2.573 0.563,0.24 12 false *B 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 1.583,0.427 1.979,0.667 0.396,0.24 10 false A48 1.583,2.448 1.979,2.688 0.396,0.24 10 false A49 0.083,1.792 0.479,2.031 0.396,0.24 10 false GND1 0.083,3.792 0.479,4.031 0.396,0.24 10 false GND1
*A except LHD with Continuously Variable Transaxle
*B for LHD with Continuously Variable Transaxle
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
except LHD with Continuously Variable Transaxle
Tester Connection Condition Specified Condition
A48-1 (GND1) - Body ground Always Below 1 Ω

for LHD with Continuously Variable Transaxle
Tester Connection Condition Specified Condition
A49-1 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (SLIP INDICATOR LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

6.READ VALUE USING GTS (SLIP INDICATOR LIGHT)
a.

Reconnect the A48*1 or A49*2 skid control ECU (brake actuator assembly) connector.

*1: except LHD with Continuously Variable Transaxle

*2: for LHD with Continuously Variable Transaxle



b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

According to the display on the GTS, read the Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Slip Indicator Light SLIP indicator light OFF or ON OFF: Indicator light off
ON: Indicator light on
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Slip Indicator Light
50003 105 304

g.

Check the GTS display condition of the slip indicator light.

Result:
Result Proceed to
Display of the Data List remains OFF A
Display of the Data List remains ON B




A

B