Home › General › SPECIFICATIONS › K411 CVT › from 2018.01
RM30M0E _V1 General _017290 SPECIFICATIONS _0273543 K411 CVT F

SPECIFICATIONS  K411 CVT  SERVICE DATA  


Continuously Variable Transaxle System
Engine stall speed D 2400 +/- 400 rpm
Secondary Oil pressure (Throttle valve fully open)*1
Engine stall speed
2400 +/- 400 rpm
D 4.4 to 6.5 MPa
(44.9 to 66.3 kgf/cm2, 638 to 943 psi)
R 4.4 to 6.8 MPa
(44.9 to 69.3 kgf/cm2, 638 to 986 psi)
Time lag N → D Less than 1.2 seconds
N → R Less than 1.5 seconds
Engine idle speed (A/C off) N 600 to 700 rpm
Shift schedule
D
Throttle valve position (100%) 40 km/h (25 mph) 4300 to 4900 rpm
70 km/h (43 mph) 5000 to 5700 rpm
100 km/h (62 mph) 5700 to 6400 rpm
Throttle valve position (Constant opening angle)*2 40 km/h (25 mph) 900 to 1400 rpm
70 km/h (43 mph) 1300 to 1800 rpm
100 km/h (62 mph) 2100 to 2600 rpm
Throttle valve position (100%) Accelerator pedal fully depressed above 70 km/h (43 mph) 3000 rpm or over
Lock-up point (Throttle valve opening 5%)
D Lock-up On 5 to 30 km/h (3 to 19 mph)
Lock-up point (Throttle valve opening 0%)
D Lock-up Off 5 to 30 km/h (3 to 19 mph)

*1: Connect terminals 13 (TC) and 4 (GC) of the DLC3 when measuring the fluid pressure.

*2: Depress the accelerator pedal at a consistent angle to maintain the specified vehicle speed.

Continuously Variable Transaxle Fluid
Dry fill 6.4 liters (6.8 US qts, 5.6 Imp. qts) Toyota Genuine CVT fluid FE

Continuously Variable Transaxle Assembly
CVT oil pump type T oil seal depth Standard -0.2 to 0.2 mm (-0.00787 to 0.00787 in.)

Torque Converter and Drive Plate
Drive plate runout Maximum 0.30 mm (0.0118 in.)

Front Differential Oil Seal
Front drive shaft oil seal LH depth Standard 2.6 to 3.6 mm (0.103 to 0.141 in.)
Front drive shaft oil seal RH depth Standard -0.5 to 0.5 mm (-0.0196 to 0.0196 in.)

Revolution Sensor
Transmission revolution sensor (NIN) resistance
1 (NIN-) - 2 (NIN+) 20°C (68°F) 560 to 680 Ω
Transmission revolution sensor (NOUT) current
1 (NOTO) - 2 (NOTB) Low signal 4 to 8 mA
High signal 12 to 16 mA
Transmission revolution sensor (NT) current
1 (NTO) - 2 (NTB) Low signal 4 to 8 mA
High signal 12 to 16 mA

Park/Neutral Position Switch
Park/neutral position switch resistance
4 (B) - 9 (L) Shift lever in P or N Below 1 Ω
Shift lever not in P and N 10 kΩ or higher
1 (RB) - 3 (PL) Shift lever in P Below 1 Ω
Shift lever not in P 10 kΩ or higher
1 (RB) - 2 (RL) Shift lever in R Below 1 Ω
Shift lever not in R 10 kΩ or higher
1 (RB) - 8 (NL) Shift lever in N Below 1 Ω
Shift lever not in N 10 kΩ or higher
1 (RB) - 7 (DL) Shift lever in D or M Below 1 Ω
Shift lever not in D and M 10 kΩ or higher

Shift Lever
Shift lock control unit assembly (w/ Smart entry and start system)
Wire harness
Tester Connection Condition Specified Condition
4 (IG) - Body ground Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V
8 (STP) - Body ground Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 V
7 (E) - Body ground Always Below 1 Ω
Shift lock solenoid
1 (SLS+) - 2 (SLS-) Always 112 Ω
4 (P) - 3 (E2) Shift lever in P 10 kΩ or higher
Shift lever not in P Below 1 Ω
Shift lock control unit assembly (w/o Smart entry and start system)
Wire harness
Tester Connection Condition Specified Condition
1 (ACC) - Body ground Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
4 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
5 (KLS+) - Body ground Ignition switch ACC and shift lever in P Below 1 V
Ignition switch ACC and shift lever not in P 11 to 14 V
8 (STP) - Body ground Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 V
7 (E) - Body ground Always Below 1 Ω
Shift lock solenoid
1 (SLS+) - 2 (SLS-) Always 112 Ω
4 (P) - 3 (E2) Shift lever in P 10 kΩ or higher
Shift lever not in P Below 1 Ω
Transmission control switch (Shift lock control unit assembly) (for LHD)
Tester Connection Condition Specified Condition
1 (SFTD) - 2 (E) Shift lever held in"-"(Downshift) Below 1 Ω
Shift lever not in"-" 10 kΩ or higher
3 (SFTU) - 2 (E) Shift lever held in"+"(Downshift) Below 1 Ω
Shift lever not in"+" 10 kΩ or higher
Transmission control switch (Shift lock control unit assembly) (for RHD)
Tester Connection Condition Specified Condition
1 (SFTU) - 2 (E) Shift lever held in"+"(Downshift) Below 1 Ω
Shift lever not in"+" 10 kΩ or higher
3 (SFTD) - 2 (E) Shift lever held in"-"(Downshift) Below 1 Ω
Shift lever not in"-" 10 kΩ or higher