FREEZE FRAME DATA
Freeze frame data values will vary depending on the measurement conditions, surroundings, or vehicle conditions. For this reason, there may be a problem even if the values are within specifications.
Turn the ignition switch ON and park the vehicle on level ground. Check the freeze frame data by using the GTS.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Check the freeze frame data on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Meter Vehicle Velocity | Vehicle speed from speedometer | Min.: 0.0 km/h (0.0 mph)
Max.: 300.0 km/h (186.4 mph) |
·
0 km/h (0 mph): Engine running and vehicle stopped ·
No significant fluctuation: Engine running and vehicle driven at constant speed |
- |
| Engine Revolution | Engine speed | Min.: 0 rpm
Max.: 12800 rpm |
Engine running at a constant speed: No significant fluctuation | - |
| Motor Actual Current | Current to motor | Min.: -327.68 A
Max.: 327.67 A |
Value changes in proportion to steering effort
-The value increases when turning left and decreases when turning right |
Engine running and steering wheel being turned |
| Command Value Current | Requested current to motor | Min.: -327.68 A
Max.: 327.67 A |
Value changes in proportion to steering effort
-The value increases when turning left and decreases when turning right |
Engine running and steering wheel being turned |
| Thermistor Temperature | ECU substrate temperature | Min.: -50.0°C (-58.0°F)
Max.: 150.0°C (302.0°F) |
-50 to 150°C (-58 to 302°F) | - |
| PIG Power Supply | Power source voltage to active motor | Min.: 0.0000 V
Max.: 20.1531 V |
11 to 14 V | Always |
| IG Power Supply | IG power source voltage | Min.: 0.0000 V
Max.: 20.1531 V |
11 to 14 V | Ignition switch ON |
| Steering Wheel Torque | Steering wheel torque | Min.: -7.00 Nm
Max.: 7.00 Nm |
Value changes in proportion to steering effort | Engine running and steering wheel being turned |
| Torque Sensor 1 Output | Torque sensor 1 output value | Min.: 0.0000 V
Max.: 4.9725 V |
·
2.3 to 2.7 V: Engine running and steering wheel not being turned (without load) ·
2.5 to 3.8 V: Engine running and steering wheel being turned to right with vehicle stopped ·
1.2 to 2.5 V: Engine running and steering wheel being turned to left with vehicle stopped |
- |
| Torque Sensor 2 Output | Torque sensor 2 output value | Min.: 0.0000 V
Max.: 4.9725 V |
·
2.3 to 2.7 V: Engine running and steering wheel not being turned (without load) ·
1.2 to 2.5 V: Engine running and steering wheel being turned to right with vehicle stopped ·
2.5 to 3.8 V: Engine running and steering wheel being turned to left with vehicle stopped |
- |
| TRQ1 Zero Point Value | Zero point value of torque sensor 1 | Min.: 0.0000 V
Max.: 4.9725 V |
2.3 to 2.7 V | Engine running and steering wheel not being turned (without load) |
| TRQ2 Zero Point Value | Zero point value of torque sensor 2 | Min.: 0.0000 V
Max.: 4.9725 V |
2.3 to 2.7 V | Engine running and steering wheel not being turned (without load) |
| Motor Terminal Volt(+) | Motor terminal M1 voltage | Min.: 0.0 V
Max.: 25.5 V |
·
11 to 14 V: Engine running and steering wheel being turned to right ·
6 to 11 V: Engine running and steering wheel being turned to left |
- |
| Motor Terminal Volt(-) | Motor terminal M2 voltage | Min.: 0.0 V
Max.: 25.5 V |
·
6 to 11 V: Engine running and steering wheel being turned to right ·
11 to 14 V: Engine running and steering wheel being turned to left |
- |
| Stop&Start Ctrl Mode | Status of the record of stop and start control mode | IG, Run, Stopreq, Stop, Restart | IG: Ignition switch ON (Before engine started)
Run: Engine running Stopreq: Engine stop requested Stop: Engine stopped Restart: Engine restarting |
This item is displayed on the GTS but is not used. |
| Steering Angle | Steering angle value | Min.: -3072.0 deg
Max.: 3070.5 deg |
- | During steering operation: Changes in proportion with steering wheel rotation |