Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › from 2018.01
RM30M0E _55 Steering _017103 POWER ASSIST SYSTEMS _0090108 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1551  IG Power Supply Voltage  


DESCRIPTION

The power steering ECU assembly distinguishes the ignition switch status as ON or off through the IG power source circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition Note
C1551 IG Power Supply Voltage Open or short in IG power source circuit with ignition switch ON
·

IG power source circuit

·

Power steering ECU assembly

·

EPS-IG fuse


EPS warning light: Comes on After normal confirmation -

WIRING DIAGRAM

C113532E89
0.792,1.031 1.76,1.24 0.969,0.208 10 false from IG Circuit 2.948,1.208 3.542,1.448 0.594,0.24 10 false EPS-IG 4.448,1.031 4.74,1.177 0.292,0.146 10 false F12 4.823,1.031 4.99,1.177 0.167,0.146 10 false IG 4.521,0.823 4.615,0.969 0.094,0.146 10 false 1 4.458,2.135 4.75,2.281 0.292,0.146 10 false F11 4.823,2.146 5.25,2.292 0.427,0.146 10 false PGND 4.531,1.927 4.625,2.073 0.094,0.146 10 false 2 4.604,2.917 6.635,3.115 2.031,0.198 10 false Power Steering ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

If the power steering ECU assembly has been replaced, perform assist map writing and torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION AND GROUND WIRE
a.

Check the connection condition of the power steering ECU assembly connectors.

OK:

The power steering ECU assembly connectors are securely connected.



b.

Check that the ground wire is securely installed with the bolt.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>INSTALLATION

OK:

The ground wire is securely installed with the bolt.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (IG POWER SUPPLY)

NG

CONNECT CONNECTOR OR INSTALL GROUND WIRE

2.READ VALUE USING GTS (IG POWER SUPPLY)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / EMPS / Data List.

Chassis > EMPS > Data List
Tester Display
IG Power Supply
50003 142 11

f.

Select the item "IG Power Supply" in the Data List and read the value displayed on the GTS.

Chassis > EMPS > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
IG Power Supply IG power source voltage Min.: 0.0000 V
Max.: 20.1531 V
11 to 14 V Ignition switch ON
OK:

The normal condition value is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (BATTERY - POWER STEERING ECU ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (BATTERY - POWER STEERING ECU ASSEMBLY)
a.
E324645C04
0.5,1.01 1,1.25 0.5,0.24 1.417,1.104 0.99,1.656 true 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 0.625,1.052 0.958,1.219 0.333,0.167 10 false F12 0.813,1.594 1.125,1.75 0.313,0.156 10 false IG
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Disconnect the power steering ECU assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F12-1 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BODY GROUND)
a.
C349134C04
1.469,0.229 1.969,0.479 0.5,0.25 2.417,1.667 2.01,1.271 true 0.083,0.083 0.313,0.323 0.229,0.24 10 false *a 1.594,0.271 2.052,0.469 0.458,0.198 10 false F11 2.302,1.698 2.917,1.896 0.615,0.198 10 false PGND
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Disconnect the power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F11-2 (PGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR