Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function) › from 2018.01
RM30M0E _58 Vehicle Interior _017111 THEFT DETERRENT / KEYLESS ENTRY _0090849 SMART ENTRY AND START SYSTEM(for Entry Function) U

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  TERMINALS OF ECU  


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


E372387E05
2.083,0.25 2.583,0.5 0.5,0.25 4.417,0.25 4.917,0.5 0.5,0.25 2.177,0.292 2.635,0.49 0.458,0.198 10 false F43 4.51,0.292 4.969,0.49 0.458,0.198 10 false F44

a.

Disconnect the F43 and F44 certification ECU (smart key ECU assembly) connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
F43-10 (E) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
F43-1 (+B) - F43-10 (E) Input B - W-B +B power supply Always 11 to 14 V -
F44-33 (CUTB) - F43-10 (E) Input L - W-B Dark current cut pin* Always 11 to 14 V -

*: In order to prevent the vehicle battery from being depleted when the vehicle is shipped long distances, a fuse that cuts unnecessary electrical load while the vehicle is being shipped is set in the circuit. If the fuse is removed, the circuit becomes open. If the fuse that is between the vehicle battery and terminal CUTB is removed and the circuit is open, the certification ECU (smart key ECU assembly) changes to a certain control mode.


If the result is not as specified, there may be a malfunction on the wire harness side or the fuse is removed.


c.

Connect the F43 and F44 certification ECU (smart key ECU assembly) connectors.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
F43-21 (ACCD) - F43-10 (E) Output L - W-B ACC signal Engine switch off → Engine switch on (ACC) 1 V or less → 8.5 V or higher -
F43-20 (IG1D) - F43-10 (E) Output BR - W-B IG1 signal Engine switch on (ACC) → Engine switch on (IG) 1 V or less → 9 V or higher -
F44-9 (CLG5) - F43-10 (E) Input/Output SB - W-B Output to driver door electrical key antenna (request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area) Procedure:
1.

Engine switch off

2.

All doors closed


Not pulse generation Overhead + Driver Side (key diagnostic mode)
Procedure:
1.

Engine switch off

2.

All doors closed

3.

While carrying the electrical key transmitter sub-assembly, press the trigger switch on the front door outside handle assembly (for driver door)


Pulse generation (See waveform 1)
F44-25 (CG5B) - F43-10 (E) Input/Output R - W-B Output to driver door electrical key antenna (terminal on opposite side of component from CLG5 output terminal) Procedure:
1.

Engine switch off

2.

All doors closed


Not pulse generation Overhead + Driver Side (key diagnostic mode)
Procedure:
1.

Engine switch off

2.

All doors closed

3.

While carrying the electrical key transmitter sub-assembly, press the trigger switch on the front door outside handle assembly (for driver door)


Pulse generation (See waveform 1)
F43-4 (TSW1) - F43-10 (E) Input BE - W-B Driver door trigger switch signal input
Sends signal from trigger switch on front door outside handle assembly (for driver door) to certification ECU (smart key ECU assembly).
Certification ECU (smart key ECU assembly) send 12 V pulse waveform every 20 ms. from terminal TSW. When trigger switch is pressed, the pulse is grounded.
Procedure:
1.

Engine switch off

2.

All doors closed

3.

Driver door trigger switch not pressed → pressed


9.5 to 16 V → Below 1.5 V D-Door Trigger Switch
F43-14 (TSW5) - F43-10 (E)*1 Input G - W-B Luggage electrical key switch signal input Luggage door opening switch assembly off → on 4.5 V or higher → Below 1.5 V Tr/B-Door Unlock SW
F43-14 (TSW5) - F43-10 (E)*2 Input G - W-B Back door opener switch assembly (unlock switch) signal input Back door opener switch assembly (unlock switch) off → on 4.5 V or higher → Below 1.5 V Tr/B-Door Unlock SW
F43-23 (TSW6) - F43-10 (E)*2 Input L - W-B Back door opener switch assembly (lock switch) signal input Back door opener switch assembly (lock switch) off → on 4.5 V or higher → Below 1.5 V Tr/B-Door Lock SW
F44-31 (CLG1) - F43-10 (E) Input/Output G - W-B Output to No. 1 indoor electrical key antenna assembly (instrument panel) Procedure:
1.

All doors closed

2.

Engine switch off

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Door is open

5.

Door is closed

6.

Within 30 seconds


Pulse generation (See waveform 2) Overhead + Room/Extra (key diagnostic mode)
F44-30 (CG1B) - F43-10 (E) Input/Output R - W-B Output to No. 1 indoor electrical key antenna assembly (instrument panel) (terminal on opposite side of component from CLG1 output terminal) Procedure:
1.

All doors closed

2.

Engine switch off

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Door is open

5.

Door is closed

6.

Within 30 seconds


Pulse generation (See waveform 2) Overhead + Room/Extra (key diagnostic mode)
F44-6 (CLG2) - F43-10 (E) Input/Output L - W-B Output to No. 2 indoor electrical key antenna assembly (rear floor) Procedure:
1.

All doors closed

2.

Engine switch off

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Door is open

5.

Door is closed

6.

Within 30 seconds


Pulse generation (See waveform 2) Overhead + Room2 (key diagnostic mode)
F44-23 (CG2B) - F43-10 (E) Input/Output BR - W-B Output to No. 2 indoor electrical key antenna assembly (rear floor) (terminal on opposite side of component from CLG2 output terminal) Procedure:
1.

All doors closed

2.

Engine switch off

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Door is open

5.

Door is closed

6.

Within 30 seconds


Pulse generation (See waveform 2) Overhead + Room2 (key diagnostic mode)
F44-28 (CLG7) - F43-10 (E)*1 Input/Output W - W-B Output to electrical key antenna (outside luggage compartment) Procedure:
1.

Engine switch off

2.

All doors closed

3.

Luggage door opening switch assembly off → on


Pulse generation (See waveform 3) Over Head + Luggage (key diagnostic mode)
F44-29 (CG7B) - F43-10 (E)*1 Input/Output GR - W-B Output to electrical key antenna (outside luggage compartment) (terminal on opposite side of component from CLG7 output terminal) Procedure:
1.

Engine switch off

2.

All doors closed

3.

Luggage door opening switch assembly off → on


Pulse generation (See waveform 3) Over Head + Luggage (key diagnostic mode)
F44-28 (CLG7) - F43-10 (E)*2 Input/Output W - W-B Output to electrical key antenna (outside luggage compartment) Procedure:
1.

Engine switch off

2.

All doors closed

3.

Back door opener switch assembly off → on


Pulse generation (See waveform 4) Over Head + Back Door (key diagnostic mode)
F44-29 (CG7B) - F43-10 (E)*2 Input/Output GR - W-B Output to electrical key antenna (outside luggage compartment) (terminal on opposite side of component from CLG7 output terminal) Procedure:
1.

Engine switch off

2.

All doors closed

3.

Back door opener switch assembly off → on


Pulse generation (See waveform 4) Over Head + Back Door (key diagnostic mode)
F43-9 (LSWP) - F43-10 (E) Input W - W-B Except driver door unlock detection switch input Procedure:
1.

Engine switch off

2.

All doors closed

3.

All doors unlocked

4.

Lock button of electrical key transmitter sub-assembly not pressed


Below 1 V -
Procedure:
1.

Engine switch off

2.

All doors closed

3.

All doors unlocked

4.

Lock button of electrical key transmitter sub-assembly pressed


8.5 V or higher -
F44-3 (RCO) - F43-10 (E) Output GR - W-B Output to door control receiver
(Power supply for door control receiver. Certification ECU (smart key ECU assembly) outputs 5 V when receiver starts operating.)
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed


Pulse generation (See waveform 5) -
F44-22 (RDAS) - F43-10 (E) Input LG - W-B Door control receiver verifies data received from electrical key transmitter sub-assembly. Door control receiver sends data to ECU and intermittently grounds 12 V signal from certification ECU (smart key ECU assembly). Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed


Pulse generation (See waveform 6) -
F44-21 (CSEL) - F43-10 (E) Output P - W-B Communication channel switching circuit Procedure:
1.

Engine switch off

2.

All doors closed


Pulse generation (See waveform 7) Key diagnostic mode
F43-2 (BZR) - F43-10 (E) Output G - W-B Wireless door lock buzzer signal Wireless door lock buzzer on Pulse generation -
F44-13 (RDA3) - F43-10 (E) Output GR - W-B Signal output to body computer Procedure:
1.

Engine switch off

2.

All doors locked

3.

10 seconds elapsed after all doors locked

4.

Electrical key transmitter sub-assembly unlock switch not pressed


11 to 14 V -
Procedure:
1.

Engine switch off

2.

All doors locked

3.

10 seconds elapsed after all doors locked

4.

Electrical key transmitter sub-assembly unlock switch pressed


Pulse generation -
F44-36 (PRG3) - F43-10 (E) Input BR - W-B Signal input from body computer Procedure:
1.

Engine switch off

2.

All doors locked

3.

10 seconds elapsed after all doors locked

4.

Electrical key transmitter sub-assembly unlock switch not pressed


11 to 14 V -
Procedure:
1.

Engine switch off

2.

All doors locked

3.

10 seconds elapsed after all doors locked

4.

Electrical key transmitter sub-assembly unlock switch pressed


Pulse generation -

*1: for Sedan

*2: for Hatchback



e.
B265917C03
0.208,1 0.594,1.229 0.385,0.229 10 GND 1.188,1.969 1.427,2.156 0.24,0.188 10 *a
*a Trigger switch ON


Using an oscilloscope, check waveform 1.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 1 (Reference)
Item Content
Tester Connection F44-9 (CLG5) - F43-10 (E)
F44-25 (CG5B) - F43-10 (E)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Procedure:
1.

Engine switch off

2.

All doors closed

3.

While carrying the electrical key transmitter sub-assembly, press the trigger switch on the driver door outside handle assembly (for driver door)




f.
B251020C20
0.854,1.875 1.042,2.083 0.188,0.208 10 false *a 1.75,1.885 1.938,2.094 0.188,0.208 10 false *b 0.208,1 0.542,1.198 0.333,0.198 10 false GND
*a Door open
*b After approximately 30 seconds from when the door is closed


Using an oscilloscope, check waveform 2.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 2 (Reference)
Item Content
Tester Connection F44-31 (CLG1) - F43-10 (E)
F44-30 (CG1B) - F43-10 (E)
F44-6 (CLG2) - F43-10 (E)
F44-23 (CG2B) - F43-10 (E)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Procedure:
1.

All doors closed

2.

Engine switch off

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Door is open

5.

Door is closed

6.

Within 30 seconds




g.
B265917C03
0.208,1 0.594,1.229 0.385,0.229 10 GND 1.188,1.969 1.427,2.156 0.24,0.188 10 *a
*a Engine switch off, all doors closed and luggage door opening switch assembly off → on


Using an oscilloscope, check waveform 3.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 4 (Reference)
Item Content
Tester Connection F44-28 (CLG7) - F43-10 (E)
F44-29 (CG7B) - F43-10 (E)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Procedure:
1.

Engine switch off

2.

All doors closed

3.

Luggage door opening switch assembly off → on




h.
B265917C03
0.208,1 0.594,1.229 0.385,0.229 10 GND 1.188,1.969 1.427,2.156 0.24,0.188 10 *a
*a Engine switch off, all doors closed and luggage door opening switch assembly off → on


Using an oscilloscope, check waveform 4.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 4 (Reference)
Item Content
Tester Connection F44-28 (CLG7) - F43-10 (E)
F44-29 (CG7B) - F43-10 (E)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Procedure:
1.

Engine switch off

2.

All doors closed

3.

Back door opener switch assembly off → on




i.
B251178C19
0.198,1 0.531,1.198 0.333,0.198 10 GND 1.01,1.885 1.198,2.042 0.188,0.156 10 *a 2.021,1.885 2.208,2.042 0.188,0.156 10 *b
*a Before lock or unlock button of electrical key transmitter sub-assembly pressed
*b After lock or unlock button of electrical key transmitter sub-assembly pressed


Using an oscilloscope, check waveform 5.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 6 (Reference)
Item Content
Tester Connection F44-3 (RCO) - F43-10 (E)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed




j.
B251177C18
0.208,1 0.542,1.198 0.333,0.198 10 GND 1.021,1.896 1.208,2.052 0.188,0.156 10 *a 2.188,1.906 2.375,2.063 0.188,0.156 10 *b
*a Before lock or unlock button of electrical key transmitter sub-assembly pressed
*b After lock or unlock button of electrical key transmitter sub-assembly pressed


Using an oscilloscope, check waveform 6.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 7 (Reference)
Item Content
Tester Connection F44-22 (RDAS) - F43-10 (E)
Tool Setting 5 V/DIV., 500 ms./DIV.
Condition Procedure:
1.

Engine switch off

2.

All doors locked

3.

Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed




k.
B348666E01
0.177,1 0.635,1.198 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 7.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 8 (Reference)
Item Content
Tester Connection F44-21 (CSEL) - F43-10 (E)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Procedure:
1.

Engine switch off

2.

All doors closed





CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND BODY COMPUTER


E381144C24
3.344,3.75 3.844,4 0.5,0.25 6.333,4.75 6.667,5 0.333,0.25 5.396,4.844 5.729,5.094 0.333,0.25 4.333,4.771 4.667,5.021 0.333,0.25 3.406,4.823 3.74,5.073 0.333,0.25 2.531,4.854 2.865,5.104 0.333,0.25 1.531,4.823 1.865,5.073 0.333,0.25 1.5,6.146 1.833,6.396 0.333,0.25 0.531,4.896 0.865,5.146 0.333,0.25 2.615,6.177 2.948,6.427 0.333,0.25 3.99,6.083 4.323,6.333 0.333,0.25 5.188,6.26 5.521,6.51 0.333,0.25 5.031,7.458 5.365,7.708 0.333,0.25 4.052,7.458 4.385,7.708 0.333,0.25 2.781,7.438 3.115,7.688 0.333,0.25 1.635,7.469 1.969,7.719 0.333,0.25 2.969,0.813 3.417,0.177 3.417,0.177 3.583,0.177 true 6.167,0.948 6.521,0.552 6.521,0.552 6.688,0.552 true 6.104,1.229 6.542,0.875 6.542,0.875 6.708,0.875 true 6.167,1.615 6.583,1.302 6.583,1.302 6.75,1.302 true 6.073,1.896 6.5,1.698 6.5,1.698 6.667,1.698 true 6.104,2.167 6.531,1.969 6.531,1.969 6.698,1.969 true 6.125,2.406 6.5,2.635 6.5,2.635 6.667,2.635 true 6.125,3.021 6.5,3.25 6.5,3.25 6.667,3.25 true 5.677,3.135 6.042,3.74 6.042,3.74 6.208,3.74 true 1.125,3.24 0.75,3.667 0.75,3.667 0.583,3.667 true 1.74,3.229 2,3.667 2,3.667 2.167,3.667 true 1.104,1.188 0.667,0.75 0.667,0.75 0.5,0.75 true 1.167,1.531 0.729,1.094 0.729,1.094 0.563,1.094 true 1.135,1.854 0.698,1.417 0.698,1.417 0.531,1.417 true 1.167,2.177 0.729,1.74 0.729,1.74 0.563,1.74 true 1.167,2.458 0.792,2.167 0.792,2.167 0.625,2.167 true 0.167,0.104 0.479,0.302 0.313,0.198 10 false *1 3.479,3.792 3.792,3.99 0.313,0.198 10 false MB 5.479,4.896 5.792,5.094 0.313,0.198 10 false 6O 3.635,0.104 3.948,0.302 0.313,0.198 10 false MB 6.406,4.792 6.719,4.99 0.313,0.198 10 false 6M 0.333,1.344 0.646,1.542 0.313,0.198 10 false 6D 3.49,4.865 3.802,5.063 0.313,0.198 10 false 6E 1.615,4.875 1.927,5.073 0.313,0.198 10 false 6A 2.615,4.896 2.927,5.094 0.313,0.198 10 false 6C 0.615,4.938 0.927,5.135 0.313,0.198 10 false 6B 1.583,6.198 1.896,6.396 0.313,0.198 10 false 6N 2.698,6.219 3.01,6.417 0.313,0.198 10 false 6J 4.083,6.125 4.396,6.323 0.313,0.198 10 false 6L 5.271,6.302 5.583,6.5 0.313,0.198 10 false 6K 5.115,7.51 5.427,7.708 0.313,0.198 10 false 6G 4.135,7.5 4.448,7.698 0.313,0.198 10 false 6F 2.865,7.479 3.177,7.677 0.313,0.198 10 false 6I 1.719,7.51 2.031,7.708 0.313,0.198 10 false 6H 0.292,0.688 0.604,0.885 0.313,0.198 10 false 6N 0.344,1.031 0.656,1.229 0.313,0.198 10 false 6O 4.417,4.813 4.729,5.01 0.313,0.198 10 false 6D 0.333,1.667 0.646,1.865 0.313,0.198 10 false 6E 0.406,2.073 0.719,2.271 0.313,0.198 10 false 6C 0.385,3.594 0.698,3.792 0.313,0.198 10 false 6A 2.24,3.604 2.552,3.802 0.313,0.198 10 false 6B 6.74,0.479 7.052,0.677 0.313,0.198 10 false 6M 6.771,0.823 7.083,1.021 0.313,0.198 10 false 6J 6.802,1.229 7.115,1.427 0.313,0.198 10 false 6L 6.729,1.615 7.042,1.813 0.313,0.198 10 false 6K 6.76,1.917 7.073,2.115 0.313,0.198 10 false 6H 6.729,2.563 7.042,2.76 0.313,0.198 10 false 6I 6.74,3.177 7.052,3.375 0.313,0.198 10 false 6F 6.281,3.656 6.594,3.854 0.313,0.198 10 false 6G
*1 Driver Side Junction Block Assembly - -


B343148C10
4.156,2.74 4.521,2.99 0.365,0.25 3.938,2.021 4.073,2.021 4.073,2.021 4.688,1.458 true 1.667,2.24 1.792,2.24 1.792,2.24 2.24,2.677 false 0.104,0.083 0.417,0.281 0.313,0.198 10 false *1 4.229,2.792 4.688,2.99 0.458,0.198 10 false F52 3.615,1.938 4.073,2.135 0.458,0.198 10 false F52 1.427,2.156 1.74,2.354 0.313,0.198 10 false MB
*1 Body Computer - -


a.

Remove the body computer from the driver side junction block assembly.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
MB-1 (GND) - Body ground - - Ground Always Below 1 Ω -
MB-6 (BECU) - Body ground Input - Battery power supply (for CPU) Always 11 to 14 V -
MB-7 (IG) - Body ground Input - Engine switch power supply Engine switch on (IG) 11 to 14 V -

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Install the body computer to the driver side junction block assembly.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
6M-2 (DCTY) - Body ground Input BR - Body ground Driver door courtesy light switch input Driver door closed → open Pulse generation (See waveform 1) -
F52-14 (PCTY) - Body ground Input LG - Body ground Except driver door courtesy light switch input All doors closed → Except driver door open Pulse generation (See waveform 1) -
6N-1 (LGCY) - Body ground*1 Input R - Body ground Luggage compartment door courtesy light switch input Luggage compartment door open Below 1 V -
Engine switch off, all doors closed and luggage compartment door closed 11 to 14 V
6N-1 (BCTY) - Body ground*2 Input R - Body ground Back door courtesy light switch input Back door open Below 1 V -
Engine switch off, all doors closed and back door closed 11 to 14 V -
F52-18 (L2) - Body ground Input V - Body ground Driver door key-linked lock input Engine switch off, all doors closed and driver door key cylinder in neutral position → lock position Pulse generation (See waveform 2) -
F52-11 (UL2) - Body ground Input L - Body ground*5
BE - Body ground*6
Driver door key-linked unlock input Engine switch off, all doors closed and driver door key cylinder in neutral position → unlock position Pulse generation (See waveform 3) -
6J-4 (ACT+) - Body ground Output SB - Body ground*3
GR - Body ground*4
Door lock motor lock drive output Driver door control switch not pushed and driver door key cylinder in neutral position Below 1 V -
Lock side of driver door control switch pushed or driver door key cylinder in lock position 11 to 14 V
6J-2 (TR+) - Body ground*1 Output L - Body ground Luggage compartment door lock motor unlock drive output Luggage compartment door closed Below 1 V -
Luggage compartment door open 11 to 14 V
6J-2 (TR+) - Body ground*2 Output L - Body ground Back door lock motor unlock drive output Back door closed Below 1 V -
Back door open 11 to 14 V -
6J-3 (ACT-) - Body ground Output R - Body ground*3
W - Body ground*4
Door lock motor unlock drive output Driver door control switch not pushed and driver door key cylinder in neutral position Below 1 V -
Unlock side of driver door control switch pushed or driver door key cylinder in unlock position 11 to 14 V
F52-15 (LSWD) - Body ground Input W - Body ground Driver door unlock detection switch input Engine switch off, all doors closed and driver door locked → unlocked Pulse generation (See waveform 4) -
F52-16 (RDA) - Body ground Input GR - Body ground Signal input from certification ECU (smart key ECU assembly) Engine switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch not pressed 11 to 14 V -
Engine switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch pressed Pulse generation -
F52-9 (PRG) - Body ground Output BR - Body ground Signal output to certification ECU (smart key ECU assembly) Engine switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch not pressed 11 to 14 V -
Engine switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch pressed Pulse generation -

*1: for Sedan

*2: for Hatchback

*3: w/ Door Control Battery

*4: w/o Door Control Battery

*5: for RHD

*6: for LHD


If the result is not as specified, the body computer or driver side junction block assembly may be malfunctioning.


e.
B341707C04
1.781,2.052 1.781,0.625 false 0.198,1.573 0.656,1.771 0.458,0.198 10 false GND 1.229,1.906 1.688,2.104 0.458,0.198 10 false *a 2.198,1.948 2.656,2.146 0.458,0.198 10 false *b
*a Door close
*b Door open


Using an oscilloscope, check waveform 1.

HINT:
·

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

·

The oscilloscope waveform shown in the illustration is status that disconnected the combination meter connector.



Waveform 1 (Reference)
Item Content
Tester Connection 6M-2 (DCTY) - Body ground
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Front door RH closed → open

waveform 1 (Reference)
Item Content
Tester Connection F52-14 (PCTY) - Body ground
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition All doors closed → Except front door RH open


f.
B341707C05
1.792,2.052 1.792,0.625 false 0.198,1.573 0.656,1.771 0.458,0.198 10 false GND 1.229,1.906 1.688,2.104 0.458,0.198 10 false *a 2.198,1.948 2.656,2.146 0.458,0.198 10 false *b
*a Neutral position
*b Lock position


Using an oscilloscope, check waveform 2.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 2 (Reference)
Item Content
Tester Connection F52-18 (L2) - Body ground
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Engine switch off, all doors closed and driver door key cylinder in neutral position → lock position


g.
B341707C06
1.792,2.052 1.792,0.625 false 0.188,1.573 0.646,1.771 0.458,0.198 10 false GND 1.229,1.906 1.688,2.104 0.458,0.198 10 false *a 2.198,1.948 2.656,2.146 0.458,0.198 10 false *b
*a Neutral position
*b Unlock position


Using an oscilloscope, check waveform 3.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


waveform 3 (Reference)
Item Content
Tester Connection F52-11 (UL2) - Body ground
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Engine switch off, all doors closed and driver door key cylinder in neutral position → unlock position


h.
B341707C07
1.792,2.052 1.792,0.625 false 0.198,1.573 0.656,1.771 0.458,0.198 10 false GND 1.229,1.906 1.688,2.104 0.458,0.198 10 false *a 2.198,1.948 2.656,2.146 0.458,0.198 10 false *b
*a Locked
*b Unlocked


Using an oscilloscope, check waveform 4.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


waveform 4 (Reference)
Item Content
Tester Connection F52-15 (LSWD) - Body ground
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Engine switch off, all doors closed and front door RH locked → unlocked