The sound signals amplified by the radio receiver assembly are sent to the speakers from the radio receiver assembly via the speaker circuit.
If there is a short in a speaker circuit, the radio receiver assembly detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is no malfunction in the radio receiver assembly or speakers.
If a short is detected in a speaker circuit, no sound can be heard from the speakers.
Disconnect the connectors from the F1 and F2 radio receiver assembly and speakers.
Measure the resistance between the radio receiver assembly and each of the front No. 1 speaker assemblies to check for an open circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F1-1 (FR+) - G3-1 | Always | Below 1 Ω |
| F1-5 (FR-) - G3-2 | Always | Below 1 Ω |
| F1-2 (FL+) - H4-1 | Always | Below 1 Ω |
| F1-6 (FL-) - H4-2 | Always | Below 1 Ω |
w/ Tweeter Speaker:
Measure the resistance between the radio receiver assembly and each of the front No. 2 speaker assemblies to check for an open circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F1-2 (FL+) - E4-4 (TWL+) | Always | Below 1 Ω |
| F1-6 (FL-) - E4-2 (TWL-) | Always | Below 1 Ω |
| F1-1 (FR+) - E3-4 (TWR+) | Always | Below 1 Ω |
| F1-5 (FR-) - E3-2 (TWR-) | Always | Below 1 Ω |
w/ Rear Speaker:
Measure the resistance between each of the rear speaker assemblies and the radio receiver assembly to check for an open circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F2-1 (RR+) - I4-1 | Always | Below 1 Ω |
| F2-3 (RR-) - I4-2 | Always | Below 1 Ω |
| F2-2 (RL+) - J4-1 | Always | Below 1 Ω |
| F2-6 (RL-) - J4-2 | Always | Below 1 Ω |
Measure the resistance between the radio receiver assembly and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F1-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| F1-5 (FR-) - Body ground | Always | 10 kΩ or higher |
| F1-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| F1-6 (FL-) - Body ground | Always | 10 kΩ or higher |
| F2-1 (RR+) - Body ground*1 | Always | 10 kΩ or higher |
| F2-3 (RR-) - Body ground*1 | Always | 10 kΩ or higher |
| F2-2 (RL+) - Body ground*1 | Always | 10 kΩ or higher |
| F2-6 (RL-) - Body ground*1 | Always | 10 kΩ or higher |
*1: w/ Rear Speaker
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | for RH |
| *B | for LH |
| *a | Component without harness connected (Front No. 1 Speaker Assembly) |
Resistance check
Remove the front No. 1 speaker assembly
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G3-1 - G3-2 | Always | 3.2 to 4.8 Ω |
| H4-1 - H4-2 | Always | 3.2 to 4.8 Ω |
| Result | Proceed to |
|---|---|
| OK (w/ Rear Speaker) | A |
| OK (w/o Rear Speaker) | B |
| NG | C |
A
B
C
| *A | for RH |
| *B | for LH |
| *a | Component without harness connected (Rear Speaker Assembly) |
Resistance check
Remove the rear speaker assembly
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I4-1 - I4-2 | Always | 3.2 to 4.8 Ω |
| J4-1 - J4-2 | Always | 3.2 to 4.8 Ω |
| Result | Proceed to |
|---|---|
| OK (w/ Tweeter Speaker) | A |
| OK (w/o Tweeter Speaker) | B |
| NG | C |
A
B
C
Check that the malfunction disappears when another speaker in good condition is installed.
Malfunction disappears.
Connect all the connectors the front No. 2 speaker assemblies.
If there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
Perform the above inspection on both LH and RH sides.
| Proceed to |
|---|
| OK |
| NG |
OK
NG