Home › Vehicle Exterior › BODY PANEL › QUARTER PANEL › 2020.03–2020.07
BM36W0E _01 Vehicle Exterior _088117 BODY PANEL _0420577 QUARTER PANEL F

BODY PANEL  QUARTER PANEL  CUT AND JOIN REPLACEMENT SECTIONS (SMALL AREAS)  


K156375

Quarter Panel Replacement Using Adhesive
1.

Cut the wheel arch portion.

2.

Heat the quarter panel adhesive area and remove the quarter panel.

HINT:

Using an industrial heater gun or gas burner, heat the quarter panel to 110 to 140°C. Make sure the quarter panel does not warp.


3.

Clean off any adhesive that remains on the vehicle.

HINT:
·

Using an industrial heater gun or gas burner, heat the adhesive to 110 to 140°C.

·

Using a scraper, scrape away the adhesive.

·

If adhesive remains, the strength of any subsequently applied adhesive will be weak.



4.

Using a disc sander or belt sander, scuff and sand any adhesive that remains on the vehicle.

HINT:

Scuff at a width of approximately 10 mm (0.39 in.) over the previous adhesive coating.


5.

Apply adhesive to the exposed metal areas on the vehicle. Using a spatula, spread the adhesive evenly.

6.

Apply adhesive to the vehicle again.

7.

Using #60-120 grit sandpaper, scuff the adhesive application area on the new quarter panel.

8.

Apply adhesive to the new quarter panel. Using a spatula, spread the adhesive evenly.

9.

Using a vise grip or the palms of your hands, press the quarter panel so that the thickness of the adhesive is even.

10.

Complete installation the new quarter panel.

11.

Dry the adhesive areas of the new quarter panel.

HINT:
·

With dryer or equivalent (60°C): 60 minutes (complete hardening: 90 minutes)

·

Ambient temperature (25°C): 12 hours (complete hardening: 24 hours)




REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts

a.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K156313C01
0,0 0,0 false
K108837

Adhesive - -



b.

After grinding off the hemming location, remove the quarter panel sub-assembly.

K156314C01
2.906,3.052 2.25,2.667 2.25,2.667 2.083,2.667 false 3.167,6.75 3,6.75 3,6.75 2.75,6.427 false 1.896,2.583 2.208,2.74 0.313,0.156 10 false *1 3.229,6.656 3.542,6.813 0.313,0.156 10 false *a 3.063,4.875 3.375,5.031 0.313,0.156 10 false *b 3.021,1.844 3.333,2 0.313,0.156 10 false *c
*1 QUARTER PANEL SUB-ASSEMBLY - -
*a Disc Sander *b Hemming Location
*c 150 mm (5.91 in.) - -


K156334



INSTALLATION


Symbol Meaning
K108821

Spot Weld
K108823

Plug Weld
K108831

Butt Weld

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Do not apply adhesive around the plug welding points.

·

Minimize squeeze out in plug welding areas.



K156313C01
0,0 0,0 false
K108837

Adhesive - -



c.

Bend the flange hem with a wooden hammer and dolly.

HINT:

Bend the panel gradually so as not to distort it.


K156315C01
2.896,3.073 2.25,2.667 2.25,2.667 2.083,2.667 false 3.802,5.25 4.083,4.917 4.083,4.917 4.25,4.917 false 3.979,5.531 4.167,5.75 4.167,5.75 4.333,5.75 false 4.083,6.417 3.917,6.417 3.917,6.417 3.75,6.073 false 1.896,2.583 2.208,2.74 0.313,0.156 10 false *1 4.146,6.323 4.458,6.479 0.313,0.156 10 false *a 4.313,4.833 4.625,4.99 0.313,0.156 10 false *b 4.396,5.656 4.708,5.813 0.313,0.156 10 false *c
*1 QUARTER PANEL SUB-ASSEMBLY - -
*a Wooden Hammer *b Dolly
*c Cloth Tape - -



d.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting/coating)


e.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


f.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.