Home › Vehicle Exterior › BODY PANEL › REAR FLOOR PAN › 2020.03–2020.07
BM36W0E _01 Vehicle Exterior _088117 BODY PANEL _0420582 REAR FLOOR PAN F

BODY PANEL  REAR FLOOR PAN  ASSEMBLY REPLACEMENT  


K156382

With the body lower back panel assembly removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points

a.

Remove the wheelhouse inner gusset front.

K155968C01
0.146,0.167 7,3.615 6.854,3.448 3.583,3.615 3.583,0.167 false 1.563,2.458 1.167,3.167 1.167,3.167 1.333,3.167 false 5.792,3.167 5.958,3.167 5.958,3.167 5.583,2.458 false 3.688,0.271 4,0.469 0.313,0.198 10 false *B 0.271,0.271 0.583,0.469 0.313,0.198 10 false *A 1.417,3.083 1.729,3.281 0.313,0.198 10 false *1 5.604,3.083 5.917,3.281 0.313,0.198 10 false *1
*A LH Side *B RH Side
*1 WHEELHOUSE INNER GUSSET FRONT - -



b.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K155969C01
0,0 0,0 false
K108837

Adhesive - -


K155970

K155971C01
0.104,0.104 0.417,0.302 0.313,0.198 10 false *A
*A LH Side - -


K155972C01
0.104,0.104 0.417,0.302 0.313,0.198 10 false *A
*A RH Side - -




INSTALLATION


Symbol Meaning
K108823

Plug Weld

a.

Before temporarily installing the new parts, weld the rear floor pan and spare wheel clamp bracket with the standard number of welding points.

K155973C01
2.75,0.667 2.917,0.667 2.917,0.667 3.167,1.052 false 3.594,2.104 4.167,3.083 4.167,3.083 4.333,3.083 false 0.104,0.104 0.417,0.302 0.313,0.198 10 false *A 2.583,0.583 2.896,0.781 0.313,0.198 10 false *1 4.417,3 4.729,3.198 0.313,0.198 10 false *2
*A Upper Face - -
*1 REAR FLOOR PAN *2 SPARE WHEEL CLAMP BRACKET



b.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Do not apply adhesive around the plug welding points.

·

Minimize squeeze out in plug welding areas.



K155969C02
0,0 0,0 false
K108837

Adhesive - -


K155974

K155975C01
0.104,0.104 0.417,0.302 0.313,0.198 10 false *A
*A LH Side - -


K155976C01
0.104,0.104 0.417,0.302 0.313,0.198 10 false *A
*A RH Side - -



c.

Weld the wheelhouse inner gusset front to the vehicle side.

K155977C01
0.146,0.167 7,3.615 6.854,3.448 3.583,3.615 3.583,0.167 false 1.563,2.458 1.167,3.167 1.167,3.167 1.333,3.167 false 5.792,3.167 5.958,3.167 5.958,3.167 5.583,2.458 false 3.688,0.271 4,0.469 0.313,0.198 10 false *B 0.271,0.271 0.583,0.469 0.313,0.198 10 false *A 1.417,3.083 1.729,3.281 0.313,0.198 10 false *1 5.604,3.083 5.917,3.281 0.313,0.198 10 false *1
*A LH Side *B RH Side
*1 WHEELHOUSE INNER GUSSET FRONT - -



d.

After welding, apply body sealer and undercoating to the corresponding parts. (See the painting /coating)


e.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.