In cases in which only one dimension is given, left and right are symmetrical.
For symbols, capital letters indicate right side of vehicle, small letters indicate left side of vehicle (seen from rear).
| Symbol | Name | Hole Diameter
mm (in.) |
|---|---|---|
| A | Back Door Hinge Installation Hole | φ8.2 (0.32) |
| a | Back Door Hinge Installation Hole | 8.2 X 10.2
(0.32 X 0.40) |
| B, b | Back Door Damper Stay Installation Nut | M6 (0.24) |
| C, c | Roof Side Inner Reinforcement Corner | - |
| D, d | Roof Side Inner Reinforcement Corner | - |
| E, e | Quarter Panel Reinforcement Extension Corner | - |
| F, f | Quarter Panel Standard Hole | φ13 (0.51) |
| G, g | Back Door Opening Trough Standard Hole | φ10 (0.39) |
| H, h | Back Door Opening Lower Reinforcement Corner | - |
| J, j | Back Door Lock Striker Installation Nut | M8 (0.31) |
| K, k | Rear Shock Absorber Installation Hole | φ24 (0.94) |
| L, l | Wheelhouse Inner Gusset Standard Hole | φ10 (0.39) |
| M, m | Center Body Pillar Assembly Mark | - |
| *a | mm
(in.) |
- | - |
| *W | Width distance | *L | Length distance |
| *X | Diagonal distance | - | - |
| *a | mm
(in.) |
- | - |
| *W | Width distance | *L | Length distance |
| *X | Diagonal distance | - | - |
Gasoline Model
In cases in which only one dimension is given, left and right are symmetrical.
For symbols, capital letters indicate right side of vehicle, small letters indicate left side of vehicle (seen from rear).
| Symbol | Name | Hole Diameter
mm (in.) |
|---|---|---|
| A | Console Installation Nut | M6 (0.24) |
| B, b | Center Floor Crossmember No.1 Standard Hole | 16X13
(0.63X0.51) |
| C, c | Quarter Wheelhouse Inner Panel Standard Hole | φ10 (0.39) |
| D, d | Seat Belt Retractor Installation Nut | M6 (0.24) |
| E, e | Flex Belt Installation Nut | M6 (0.24) |
| F, f | Wheelhouse Inner Gusset Standard Hole | φ10 (0.39) |
| G, g | Quarter Panel Reinforcement Extension Standard Hole | φ10 (0.39) |
| H, h | Back Door Opening Lower Reinforcement Standard Hole | φ10 (0.39) |
| J, j | Back Door Opening Lower Reinforcement Standard Hole | φ10 (0.39) |
| K, k | Body Lower Back Panel Reinforce Standard Hole | φ10 (0.39) |
| L, l | Back Door Lock Striker Installation Nut | M8 (0.31) |
| M, m | Rear Combination Lamp Installation Hole | 9X9
(0.35X0.35) |
| N, n | Rear Combination Lamp Installation Hole | 9X9
(0.35X0.35) |
| O, o | Rear Bumper Installation Nut | M6 (0.24) |
| P, p | Rear Combination Lamp Installation Hole | 12X8
(0.47X0.31) |
| Q, q | Rear Bumper Retainer Installation Hole | 9X9
(0.35X0.35) |
| R, r | Rear Bumper Reinforcement Installation Nut | M8 (0.31) |
| *a | mm
(in.) |
- | - |
| *a | mm
(in.) |
- | - |
| *L | Length distance | *X | Diagonal distance |
HV Model
Point B, b on the vehicle are asymmetrical.
In cases in which only one dimension is given, left and right are symmetrical.
For symbols, capital letters indicate right side of vehicle, small letters indicate left side of vehicle (seen from rear).
| Symbol | Name | Hole Diameter
mm (in.) |
|---|---|---|
| A | Console Installation Nut | M6 (0.24) |
| B | Center Floor Crossmember No.1 Standard Hole | 16X13
(0.63X0.51) |
| b | Center Floor Crossmember No.1 Standard Hole | φ13 (0.51) |
| C, c | Quarter Wheelhouse Inner Panel Standard Hole | φ10 (0.39) |
| D, d | Seat Belt Retractor Installation Nut | M6 (0.24) |
| E, e | Flex Belt Installation Nut | M6 (0.24) |
| F, f | Wheelhouse Inner Gusset Standard Hole | φ10 (0.39) |
| G, g | Quarter Panel Reinforcement Extension Standard Hole | φ10 (0.39) |
| H, h | Back Door Opening Lower Reinforcement Standard Hole | φ10 (0.39) |
| J, j | Back Door Opening Lower Reinforcement Standard Hole | φ10 (0.39) |
| K, k | Body Lower Back Panel Reinforce Standard Hole | φ10 (0.39) |
| L, l | Back Door Lock Striker Installation Nut | M8 (0.31) |
| M, m | Rear Combination Lamp Installation Hole | 9X9
(0.35X0.35) |
| N, n | Rear Combination Lamp Installation Hole | 9X9
(0.35X0.35) |
| O, o | Rear Bumper Installation Nut | M6 (0.24) |
| P, p | Rear Combination Lamp Installation Hole | 12X8
(0.47X0.31) |
| Q, q | Rear Bumper Retainer Installation Hole | 9X9
(0.35X0.35) |
| R, r | Rear Bumper Reinforcement Installation Nut | M8 (0.31) |
|
Symmetric distance |
|
Asymmetric distance |
| *a | mm
(in.) |
- | - |
| *L | Length distance | *X | Diagonal distance |
| *a | mm
(in.) |
- | - |
| *L | Length distance | *X | Diagonal distance |