Home › Vehicle Exterior › BODY PANEL › FRONT SIDE MEMBER (for 3 Door) › from 2020.09
BM36W0E _01 Vehicle Exterior _088117 BODY PANEL _0449241 FRONT SIDE MEMBER(for 3 Door) F

BODY PANEL  FRONT SIDE MEMBER(for 3 Door)  ASSEMBLY REPLACEMENT  


K159791

With the radiator side support assembly and front fender apron assembly removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108820

Remove Weld Points

a.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K158784C02
0.156,0.156 0.469,0.354 0.313,0.198 10 false *A
*A LH - -
K108837

Adhesive - -


K158785C02
0.156,0.156 0.469,0.354 0.313,0.198 10 false *A
*A LH - -



b.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K158786C02
0.156,0.156 0.469,0.354 0.313,0.198 10 false *A
*A RH - -
K108837

Adhesive - -


K158787C02
0.156,0.156 0.469,0.354 0.313,0.198 10 false *A
*A RH - -



c.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K158788C02
0,0 0,0 false
K108837

Adhesive - -


K158789



INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108824

Plug Weld
K108825

Plug Weld
K108830

Fillet Weld

a.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


b.

Make sure to attach correctly in accordance with the body dimension diagram as this part affects the front wheel alignment.

K158790C02
3.25,1 3.667,0.583 3.667,0.583 3.833,0.583 false 5.167,4.083 5,4.083 5,4.083 4.5,3.583 false 0.167,0.167 0.479,0.323 0.313,0.156 10 false *A 3.875,0.521 4.188,0.677 0.313,0.156 10 false *1 5.208,4.01 5.521,4.167 0.313,0.156 10 false *2 0.219,1.125 0.531,1.281 0.313,0.156 10 false *a 2.031,1.958 2.344,2.115 0.313,0.156 10 false *a
*A LH - -
*1 FRONT SIDE MEMBER SUB-ASSEMBLY OUTER *2 FRONT SIDE MEMBER SUB-ASSEMBLY INNER
*a 20 mm (0.79 in.) - -


K158791C02
2,2.083 2.167,2.083 2.167,2.083 2.75,1.5 false 2.875,3.927 3.042,3.927 3.042,3.927 3.625,3.427 false 0.167,0.167 0.479,0.323 0.313,0.156 10 false *A 2.688,3.875 3,4.031 0.313,0.156 10 false *1 1.813,2.021 2.125,2.177 0.313,0.156 10 false *2
*A RH - -
*1 FRONT SIDE MEMBER SUB-ASSEMBLY OUTER *2 FRONT SIDE MEMBER SUB-ASSEMBLY INNER



c.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Do not apply adhesive around the plug welding points.

·

Minimize squeeze out in plug welding areas.



K158788C02
0,0 0,0 false
K108837

Adhesive - -


K158792


d.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Do not apply adhesive around the plug welding points.

·

Minimize squeeze out in plug welding areas.



K158784C02
0.156,0.156 0.469,0.354 0.313,0.198 10 false *A
*A LH - -
K108837

Adhesive - -


K158793C02
0.156,0.156 0.469,0.354 0.313,0.198 10 false *A
*A LH - -



e.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Do not apply adhesive around the plug welding points.

·

Minimize squeeze out in plug welding areas.



K158786C02
0.156,0.156 0.469,0.354 0.313,0.198 10 false *A
*A RH - -
K108837

Adhesive - -


K158794C02
0.156,0.156 0.469,0.354 0.313,0.198 10 false *A
*A RH - -



f.

After welding, apply body sealer and undercoating to the corresponding parts. (See the painting/coating)


g.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.