Home › Vehicle Exterior › BODY PANEL › FRONT BODY PILLAR (for 3 Door) › from 2020.09
BM36W0E _01 Vehicle Exterior _088117 BODY PANEL _0449244 FRONT BODY PILLAR(for 3 Door) F

BODY PANEL  FRONT BODY PILLAR(for 3 Door)  CUT AND JOIN REPLACEMENT SECTIONS (PATTERN 1)  


K159794

With the cowl top side upper panel assembly removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108820

Remove Weld Points
K108826

Cut with Disc Sander etc.
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts

a.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K158924C01
0,0 0,0 false
K108837

Adhesive - -



b.

Remove the side panel sub-assembly inner.

K158919C01
1.417,4.667 1.583,4.667 1.583,4.667 1.969,3.865 false 1.24,4.594 1.552,4.75 0.313,0.156 10 false *1 2.427,2 2.74,2.156 0.313,0.156 10 false *a
*1 SIDE PANEL SUB-ASSEMBLY INNER - -
*a 95 mm (3.74 in.) - -


K158920

K158921


c.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K158925C01
0,0 0,0 false
K108837

Adhesive - -



d.

Remove the front pillar reinforcement sub-assembly lower.

K158922C01
2.177,1.646 1.917,0.865 1.917,0.865 1.75,0.865 false 1.563,0.813 1.875,0.969 0.313,0.156 10 false *1
*1 FRONT PILLAR REINFORCEMENT SUB-ASSEMBLY LOWER - -


K158923



INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108825

Plug Weld
K108830

Fillet Weld
K108831

Butt Weld
K108834

Body Sealer

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Do not apply adhesive around the plug welding points.

·

Minimize squeeze out in plug welding areas.



K158925C01
0,0 0,0 false
K108837

Adhesive - -



d.

Weld the front pillar reinforcement sub-assembly lower to the vehicle side.

K158927C01
2.167,1.646 2,0.854 2,0.854 1.833,0.854 false 1.635,0.792 1.948,0.948 0.313,0.156 10 false *1 4.917,4.375 5.229,4.573 0.313,0.198 10 false *a
*1 FRONT PILLAR REINFORCEMENT SUB-ASSEMBLY LOWER - -
*a 15 mm (0.59 in.) - -


K158928


e.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


K158926


f.

Apply body sealer in an even, continuous bead.

HINT:
·

Do not apply adhesive around the plug welding points.

·

Minimize squeeze out in plug welding areas.



K158924C01
0,0 0,0 false
K108837

Adhesive - -



g.

Weld the side panel sub-assembly inner to the vehicle side.

K158929C01
1.333,4.333 1.5,4.333 1.5,4.333 1.906,3.469 false 1.156,4.26 1.469,4.417 0.313,0.156 10 false *1
*1 SIDE PANEL SUB-ASSEMBLY INNER - -


K158930


h.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting/coating)


i.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


j.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.