Home › Vehicle Exterior › BODY PANEL › FRONT BODY PILLAR (for 3 Door) › from 2020.09
BM36W0E _01 Vehicle Exterior _088117 BODY PANEL _0449244 FRONT BODY PILLAR(for 3 Door) F

BODY PANEL  FRONT BODY PILLAR(for 3 Door)  CUT AND JOIN REPLACEMENT SECTIONS (PATTERN 2)  


K159795

With the cowl top side upper panel assembly and roof panel assembly removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108820

Remove Weld Points
K108826

Cut with Disc Sander etc.
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts

a.

Do not butt weld or heat repair because the heat decreases the strength of areas where ultra high strength steel is used. (See the introduction)


b.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K158938C01
0,0 0,0 false
K108837

Adhesive - -



c.

Remove the side panel sub-assembly inner.

K158931C01
2.188,1.563 1.844,1.104 1.844,1.104 1.677,1.104 false 1.49,1.052 1.802,1.208 0.313,0.156 10 false *1 4.198,1.354 4.51,1.51 0.313,0.156 10 false *a
*1 SIDE PANEL SUB-ASSEMBLY INNER - -
*a 195 mm (7.68 in.) - -


K158932

K158933


d.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K158940C01
0,0 0,0 false
K108837

Adhesive - -



e.

Remove the front body pillar sub-assembly outer and front pillar reinforcement sub-assembly lower.

K158934C01
3,1.167 2.667,0.25 2.667,0.25 2.5,0.25 false 2.604,3.833 3,4.333 3,4.333 3.167,4.333 false 2.333,0.188 2.646,0.344 0.313,0.156 10 false *1 3.24,4.281 3.552,4.438 0.313,0.156 10 false *2
*1 FRONT BODY PILLAR SUB-ASSEMBLY OUTER *2 FRONT PILLAR REINFORCEMENT SUB-ASSEMBLY LOWER


K158935

K158936



INSTALLATION


Symbol Meaning
K108821

Spot Weld
K108823

Plug Weld
K108824

Plug Weld
K108825

Plug Weld
K108830

Fillet Weld
K108831

Butt Weld
K108834

Body Sealer

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

Before temporarily installing the new parts, weld the front body pillar sub-assembly outer and front pillar reinforcement sub-assembly lower with the standard number of welding points.

K158937C01
1.948,1.167 1.698,0.813 1.698,0.813 1.531,0.813 false 1.646,3.375 1.948,2.875 1.948,2.875 2.115,2.875 false 1.365,0.74 1.677,0.896 0.313,0.156 10 false *1 2.177,2.813 2.49,2.969 0.313,0.156 10 false *2
*1 FRONT BODY PILLAR SUB-ASSEMBLY OUTER *2 FRONT PILLAR REINFORCEMENT SUB-ASSEMBLY LOWER



d.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Do not apply adhesive around the plug welding points.

·

Minimize squeeze out in plug welding areas.



K158940C01
0,0 0,0 false
K108837

Adhesive - -



e.

Weld the front body pillar sub-assembly outer and front pillar reinforcement sub-assembly lower to the vehicle side.

K158941C01
3.031,1.167 2.667,0.25 2.667,0.25 2.5,0.25 false 2.604,3.833 3.083,4.417 3.083,4.417 3.25,4.417 false 2.313,0.198 2.625,0.354 0.313,0.156 10 false *1 3.333,4.344 3.646,4.5 0.313,0.156 10 false *2
*1 FRONT BODY PILLAR SUB-ASSEMBLY OUTER *2 FRONT PILLAR REINFORCEMENT SUB-ASSEMBLY LOWER
*a Ultra High Strength Steel Welding Point *b Ultra High Strength Steel Welding Point


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 2 panels together including 980 MPa ultra high strength steel.

*a: Spot weld Pressure 2940 N (300 kgf, 661 lbf)
Weld current 10000 A
Weld time 16 Cyc.(0.34 Sec.)
*b: Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-6/ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar + CO2 20 to 30% or Ar + O2 2%) as the shield gas when plug welding. Sufficient weld strength cannot be assured when using 100% CO2 shield gas.



K158942C01
0,0 0,0 false
*a Ultra High Strength Steel Welding Point *b Ultra High Strength Steel Welding Point


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 2 panels together including 980 MPa ultra high strength steel.

*a: Spot weld Pressure 2940 N (300 kgf, 661 lbf)
Weld current 10000 A
Weld time 16 Cyc.(0.34 Sec.)
*b: Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-6/ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar + CO2 20 to 30% or Ar + O2 2%) as the shield gas when plug welding. Sufficient weld strength cannot be assured when using 100% CO2 shield gas.



K158943C01
5.615,0.521 5.927,0.677 0.313,0.156 10 false *a
*a 15 mm (0.59 in.) - -



f.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


K158939


g.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Do not apply adhesive around the plug welding points.

·

Minimize squeeze out in plug welding areas.



K158938C01
0,0 0,0 false
K108837

Adhesive - -



h.

Weld the side panel sub-assembly inner to the vehicle side.

K158944C01
2.135,1.604 1.833,1.083 1.833,1.083 1.667,1.083 false 1.479,0.99 1.792,1.146 0.313,0.156 10 false *1
*1 SIDE PANEL SUB-ASSEMBLY INNER - -
*a Ultra High Strength Steel Welding Point - -


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 3 panels or more together including 980 MPa ultra high strength steel. (When plug welding a third panel to 2 panels which are welded under the conditions described above.)

*a: Plug weld Plug diameter Same as the standard method (See the introduction)
Wire type AWS A5.18 ER70S-6/ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar + CO2 20 to 30% or Ar + O2 2%) as the shield gas when plug welding. Sufficient weld strength cannot be assured when using 100% CO2 shield gas.



K158945C01
0,0 0,0 false
*a Ultra High Strength Steel Welding Point - -


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 3 panels or more together including 980 MPa ultra high strength steel. (When plug welding a third panel to 2 panels which are welded under the conditions described above.)

*a: Plug weld Plug diameter Same as the standard method (See the introduction)
Wire type AWS A5.18 ER70S-6/ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar + CO2 20 to 30% or Ar + O2 2%) as the shield gas when plug welding. Sufficient weld strength cannot be assured when using 100% CO2 shield gas.




i.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting/coating)


j.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


k.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.