Home › Vehicle Exterior › BODY PANEL › ROCKER PANEL (for 3 Door) › from 2020.09
BM36W0E _01 Vehicle Exterior _088117 BODY PANEL _0449247 ROCKER PANEL(for 3 Door) F

BODY PANEL  ROCKER PANEL(for 3 Door)  CUT AND JOIN REPLACEMENT SECTIONS  


K159798

With the front body pillar cut and join replacement sections (pattern 1) and quarter panel cut and join replacement sections (small areas) removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108820

Remove Weld Points
K108827

Cut and Join Location

a.

Do not butt weld or heat repair because the heat decreases the strength of areas where ultra high strength steel is used. (See the introduction)


b.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K158962C01
0,0 0,0 false
K108837

Adhesive - -



c.

Remove the center body pillar reinforcement sub-assembly, rocker reinforce sub-assembly outer, step plate sub-assembly lower and center body pillar reinforce sub-assembly lower.

K158956C01
3,1.917 3.167,1.917 3.167,1.917 3.594,3.281 false 6.417,3.75 6.25,3.75 6.25,3.75 5.813,3.469 false 2.333,4.583 2.167,4.583 2.167,4.583 1.844,3.76 false 2.823,1.854 3.135,2.01 0.313,0.156 10 false *1 6.5,3.688 6.813,3.844 0.313,0.156 10 false *3 2.375,4.521 2.688,4.677 0.313,0.156 10 false *2 3.573,2.813 3.885,2.969 0.313,0.156 10 false *a
*1 CENTER BODY PILLAR REINFORCEMENT SUB-ASSEMBLY *2 ROCKER REINFORCE SUB-ASSEMBLY OUTER
*3 STEP PLATE SUB-ASSEMBLY LOWER - -
*a 80 mm (3.15 in.) - -


K158957

K158958C01
4.146,2.76 4.75,2.583 4.75,2.583 4.917,2.583 false 4.99,2.531 5.302,2.688 0.313,0.156 10 false *1 4.385,2.385 4.698,2.542 0.313,0.156 10 false *a
*1 CENTER BODY PILLAR REINFORCE SUB-ASSEMBLY LOWER - -
*a 120 mm (4.72 in.) - -




INSTALLATION


Symbol meaning
K108823

Plug weld
K108825

Plug weld
K108831

Butt Weld

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Do not apply adhesive around the plug welding points.

·

Minimize squeeze out in plug welding areas.



K158961C01
0,0 0,0 false
K108837

Adhesive - -



d.

Before temporarily installing the new parts, weld the rocker reinforce sub-assembly outer, step plate sub-assembly lowe, center body pillar reinforcement sub-assembly and center body pillar reinforce sub-assembly lower with the standard number of welding points.

K159486C01
2.083,1.917 2.25,1.917 2.25,1.917 2.396,1.396 false 6.177,0.938 6.417,0.5 6.417,0.5 6.583,0.5 false 1.896,1.865 2.208,2.021 0.313,0.156 10 false *1 6.677,0.438 6.99,0.594 0.313,0.156 10 false *2
*1 ROCKER REINFORCE SUB-ASSEMBLY OUTER *2 STEP PLATE SUB-ASSEMBLY LOWER
*a Ultra High Strength Steel Welding Point - -


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 2 panels together including 1180 MPa ultra high strength steel.

*a: Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-6/ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar + CO2 20 to 30% or Ar + O2 2%) as the shield gas when plug welding. Sufficient weld strength cannot be assured when using 100% CO2 shield gas.



K158960C01
4.781,1.438 4.917,0.5 4.917,0.5 5.083,0.5 false 1.75,6.167 1.917,6.167 1.917,6.167 2.229,5.26 false 5.146,0.458 5.458,0.615 0.313,0.156 10 false *1 1.552,6.115 1.865,6.271 0.313,0.156 10 false *2
*1 CENTER BODY PILLAR REINFORCEMENT SUB-ASSEMBLY *2 CENTER BODY PILLAR REINFORCE SUB-ASSEMBLY LOWER



e.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Do not apply adhesive around the plug welding points.

·

Minimize squeeze out in plug welding areas.



K158962C01
0,0 0,0 false
K108837

Adhesive - -



f.

Weld the rocker reinforce sub-assembly outer, step plate sub-assembly lowe, center body pillar reinforcement sub-assembly and center body pillar reinforce sub-assembly lower to the vehicle side.

K158964C01
2.333,4.583 2.167,4.583 2.167,4.583 1.854,3.771 false 3.167,2 3.333,2 3.333,2 3.698,3.25 false 5.823,3.5 6.417,3.75 6.417,3.75 6.583,3.75 false 2.385,4.531 2.698,4.688 0.313,0.156 10 false *1 6.656,3.688 6.969,3.844 0.313,0.156 10 false *2 2.979,1.948 3.292,2.104 0.313,0.156 10 false *3
*1 ROCKER REINFORCE SUB-ASSEMBLY OUTER *2 STEP PLATE SUB-ASSEMBLY LOWER
*3 CENTER BODY PILLAR REINFORCEMENT SUB-ASSEMBLY - -
*a Ultra High Strength Steel Welding Point - -


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 2 panels together including 1180 MPa ultra high strength steel.

*a: Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-6/ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar + CO2 20 to 30% or Ar + O2 2%) as the shield gas when plug welding. Sufficient weld strength cannot be assured when using 100% CO2 shield gas.



K158965

K158966C01
4.083,2.74 4.667,2.167 4.667,2.167 4.833,2.167 false 4.938,2.094 5.25,2.25 0.313,0.156 10 false *1
*1 CENTER BODY PILLAR REINFORCE SUB-ASSEMBLY LOWER - -



g.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting /coating)


h.

After welding, apply body sealer to the corresponding parts. (See the painting /coating)


i.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.