Home › Vehicle Exterior › BODY PANEL › ROCKER REAR PANEL (for 3 Door) › from 2020.09
BM36W0E _01 Vehicle Exterior _088117 BODY PANEL _0449248 ROCKER REAR PANEL(for 3 Door) F

BODY PANEL  ROCKER REAR PANEL(for 3 Door)  CUT AND JOIN REPLACEMENT SECTIONS  


K159799

quarter panel cut and join replacement sections (small areas) removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108827

Remove Weld Points

a.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K158971C01
0,0 0,0 false
K108837

Adhesive - -



b.

Remove the A.

HINT:

A is reused.


K158967C01
1.25,4.25 1.417,4.25 1.417,4.25 1.688,3.479 false 1.594,2.792 1.906,2.99 0.313,0.198 10 false *a 1.125,4.188 1.281,4.385 0.156,0.198 10 false A
*a 80 mm (3.15 in.) - -



c.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K158970C01
0,0 0,0 false
K108837

Adhesive - -



d.

Remove the step plate sub-assembly lower.

K158968C01
3.813,3.281 4.417,3.583 4.417,3.583 4.583,3.583 false 4.646,3.521 4.958,3.677 0.313,0.156 10 false *1 2.198,3.76 2.51,3.917 0.313,0.156 10 false *a
*1 STEP PLATE SUB-ASSEMBLY LOWER - -
*a 100 mm (3.94 in.)


K158969



INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108831

Butt Weld

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Do not apply adhesive around the plug welding points.

·

Minimize squeeze out in plug welding areas.



K158970C01
0,0 0,0 false
K108837

Adhesive - -



d.

Weld the step plate sub-assembly lower to the vehicle side.

K158972C01
3.813,3.281 4.333,3.604 4.333,3.604 4.5,3.604 false 4.563,3.542 4.875,3.698 0.313,0.156 10 false *1
*1 STEP PLATE SUB-ASSEMBLY LOWER - -


K158973


e.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Do not apply adhesive around the plug welding points.

·

Minimize squeeze out in plug welding areas.



K158971C01
0,0 0,0 false
K108837

Adhesive - -



f.

Weld the A to the vehicle side.

K158974N01
1.333,4.25 1.5,4.25 1.5,4.25 1.74,3.479 false 1.198,4.177 1.354,4.375 0.156,0.198 10 false A


g.

After welding, apply body sealer to the corresponding parts. (See the painting /coating)


h.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.