Home › Vehicle Exterior › BODY PANEL › ROOF PANEL (for Carbon Fiber Reinforced Plastic Roof) › from 2020.09
BM36W0E _01 Vehicle Exterior _088117 BODY PANEL _0449258 ROOF PANEL(for Carbon Fiber Reinforced Plastic Roof) F

BODY PANEL  ROOF PANEL(for Carbon Fiber Reinforced Plastic Roof)  ASSEMBLY REPLACEMENT  


·
K159810


·

Work procedures for replacement of Carbon Fiber Reinforced Plastic Roof Panel


CARBON FIBER REINFORCED PLASTIC ROOF PANEL REMOVAL


a.
K159012C01
2.802,1.906 2.635,1.906 2.635,1.906 2.552,1.635 false 2.854,1.833 3.167,1.99 0.313,0.156 10 false *a
*a Protect Cover


Vehicle protection

i.

To prevent adhesion of adhesive etc., cover the outer panels (doors, hoods, etc.) and the entire interior with protection covers to protect them.


ii.
K159013C01
2.167,2.688 2,2.688 2,2.688 1.667,2.271 false 2.458,3.281 2.75,3 2.75,3 2.917,3 false 2.229,2.615 2.542,2.771 0.313,0.156 10 false *a 3,2.927 3.313,3.083 0.313,0.156 10 false *a
*a Masking
K108837

Adhesive


Mask the outer panels including surfaces of the left and right roof side rails.



b.

Remove the rivets.


c.

Remove the roof panel support.

K160371C01
6.354,2.354 6.333,1.667 6.333,1.667 6.167,1.667 false 6.604,2.667 6.5,3.25 6.5,3.25 6.667,3.25 false 6,1.615 6.313,1.771 0.313,0.156 10 false *1 6.729,3.177 6.979,3.438 0.25,0.26 10 false *2
*1 ROOF PANEL SUPPORT *2 RIVETS



d.
K159014C01
2.083,0.167 1.917,0.167 1.917,0.167 1.729,0.375 false 2.979,1.438 2.813,1.438 2.813,1.438 2.729,1.021 false 3.01,1.354 3.323,1.51 0.313,0.156 10 false *1 2.167,0.094 2.479,0.25 0.313,0.156 10 false *a
*1 WINDSHIELD HEADER PANEL
*a Scraper


Separate the mastic sealer.

i.

Separate the mastic sealer between the windshield header panel and the carbon fiber reinforced plastic roof panel using a scraper or an equivalent tool.


ii.

Separate the mastic sealer between the roof panel reinforcement and the carbon fiber reinforced plastic roof panel using a scraper or an equivalent tool.

HINT:

Mastic sealerr application areas.

K159015




e.
K159016C01
0.583,1.5 0.75,1.5 0.75,1.5 1.063,1.813 false 2.594,1.688 2.833,1.417 2.833,1.417 3,1.417 false 0.385,1.427 0.698,1.583 0.313,0.156 10 false *a 3.063,1.354 3.375,1.51 0.313,0.156 10 false *b
*a Industrial Heater Gun
*b Scraper


Separate the adhesive.

i.

While heating the flange area of the carbon fiber reinforced plastic roof panel and the windshield header panel using an industrial heater gun from the inside, separate the adhesive using a scraper or an equivalent tool from the outside.

NOTICE:

Only insert the scraper. Do not pry it.



ii.

While heating the flange area of the carbon fiber reinforced plastic roof panel and the roof panel reinforcement rear using an industrial heater gun from the inside, separate the adhesive using a scraper or an equivalent tool from the outside.


iii.
K139627C01
0.417,1.083 0.583,1.083 0.583,1.083 0.833,0.75 false 0.219,1 0.531,1.156 0.313,0.156 10 false *a
*a Flange Edge
K108837

Adhesive


While heating the flange area of the carbon fiber reinforced plastic roof panel and the roof panel side rail using an industrial heater gun from the inside, separate the adhesive using a windshield knife or an equivalent tool from the outside.

HINT:

Use an industrial heater gun (160 to 200 °C) to apply heat.


K159017C01
5.49,2.146 6.083,1.667 6.083,1.667 6.25,1.667 false 6.313,1.604 6.625,1.802 0.313,0.198 10 false *1
*1 ROOF PANEL - -
K108837

Adhesive - -





INSTALLATION OF CARBON FIBER REINFORCED PLASTIC ROOF PANEL


a.

Remove the adhesive.

i.

Remove the adhesive remaining on the vehicle using a scraper or an equivalent tool while heating with an industrial heater gun.



b.

Remove the mastic sealer.

i.

Remove the mastic sealer remaining on the vehicle using a wire brush.



c.

Scuff the adhesive application area.

i.

Scuff the adhesive application area on the vehicle using a belt sander.



d.

Scuff the mastic sealer application area.

i.

Scuff the mastic sealer application area on the vehicle using a wire brush and a sanding paper (#320).



e.

Repair the windshield header panel and the back window frame.

i.

Repair deformation of the flange area using a wooden hammer and a dolly.



f.

Apply primer surfacer.

NOTICE:

Do not apply primer surfacer to the adhesive application area because adhesive needs to be applied to a bare steel sheet area to maintain its adhering strength.


i.

Scuff the primer surfacer application area using a sanding paper (#320).


ii.

Clean and degrease the scuffed area.


iii.

Mask the adhesive application area.


iv.

Mask the area other than the primer surfacer application area.


v.

Make sure that the vehicle is appropriately protected. Apply primer surfacer.

NOTICE:

Apply primer surfacer to the area burned by the industrial heater gun.




g.

Protect the carbon fiber reinforced plastic roof panel.

i.

Protect the entire surface of the carbon panel using a vinyl sheet or an equivalent material.



h.

Protect the vehicle.

i.

Mask the outer panels including surfaces of the left and right roof side rails.

NOTICE:

Do not masking the adhesive application area.




i.

Position the carbon fiber reinforced plastic roof panel.

i.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


ii.

After installation of the front and rear guide pins, place the new part temporarily to check the position.

K159018C01
0.75,1.75 0.917,1.75 0.917,1.75 1.219,0.969 false 6.333,1.75 6.167,1.75 6.167,1.75 5.615,0.76 false 0.583,1.677 0.896,1.833 0.313,0.156 10 false *a 6.385,1.688 6.698,1.844 0.313,0.156 10 false *a 0.083,0.177 0.396,0.333 0.313,0.156 10 false *A 4,0.177 4.313,0.333 0.313,0.156 10 false *B
*A Front Side *B Rear Side
*a Guide Pin - -




j.

Remove the carbon fiber reinforced plastic roof panel.


k.

Scuff, clean, and degrease the adhering surface and the sealer application area on the vehicle.

i.

Scuff the application area of the carbon fiber reinforced plastic roof panel flange using a sanding paper (#320).


ii.

Clean and degrease the adhesive and body sealer application area.



l.

Scuff, clean, and degrease the adhering surface and the sealer application area on the carbon fiber reinforced plastic roof panel.

i.

Scuff the application area of the carbon fiber reinforced plastic roof panel flange using a sanding paper (#320).


ii.

Clean and degrease the adhesive and body sealer application area.



m.

Apply body sealer.

i.

Apply body sealer to the marking positions of the carbon fiber reinforced plastic roof panel.

HINT:
·

Apply sealer so that the applied sealer has the height of approximately 10 mm (0.39 in.) and the diameter of approximately 10 mm (0.39 in.).

·

Body sealerr application areas.



K159020



n.
K159021C01
0,0 0,0 false
K108837

Adhesive


Apply adhesive to the vehicle.

i.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115) to the bare steel sheet area and use a spatula to make it uniform (primary coating of adhesive).



o.

Apply adhesive to the carbon fiber reinforced plastic roof panel.

i.
K118574C01
1.719,1.385 1.719,0.552 false 2.146,1.385 2.146,0.771 false 2.458,1.385 1.208,1.385 1.208,1.385 1.208,0.74 false 2.5,1.292 2.813,1.448 0.313,0.156 10 false *a
*a Sucker Grip


Attach sucker grips on the carbon fiber reinforced plastic roof panel.

NOTICE:
·

Clean the sucking surface of the sucker grips before use in order to prevent damage of the carbon fiber reinforced plastic roof panel.

·

The sucker grip cannot stick to the vinyl surface. Make holes on the vinyl sheet and attach the sucker grips directly on the carbon fiber reinforced plastic roof panel.

·

Make sure that the sucker grips do not come off.




ii.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115) to all around the flange.

NOTICE:

Apply adhesive evenly so that the carbon fiber reinforced plastic roof substrate does not come into direct contact with the exposed areas of the steel plate in order to prevent galvanic corrosion.


HINT:
·

Apply adhesive to the front and back flanges so that the applied adhesive has the height of approximately 5 mm (0.20 in.) and the width of approximately 12 mm (0.47 in.).

·

Apply adhesive to the left and right flanges so that the applied adhesive has the height of approximately 4 mm (0.16 in.) and the width of approximately 9 mm (0.35 in.).



K159022C01
5.417,0.781 5.729,0.938 0.313,0.156 10 false *a 5.938,1.198 6.25,1.354 0.313,0.156 10 false *b 5.677,2.813 5.99,2.969 0.313,0.156 10 false *c 6.104,3.354 6.417,3.51 0.313,0.156 10 false *d
*a 12 mm (0.47 in.) *b 5.0 mm (0.20 in.)
*c 4.0 mm (0.16 in.) *d 9.0 mm (0.35 in.)
K108837

Adhesive - -




p.

Install the carbon fiber reinforced plastic roof panel.

i.

Bring the carbon roof panel from the rear side of the vehicle. Install the roof to the vehicle horizontally after checking that the guide pins for longitudinal positioning have been inserted into the mounting holes.

K159018C01
0.75,1.75 0.917,1.75 0.917,1.75 1.219,0.969 false 6.333,1.75 6.167,1.75 6.167,1.75 5.615,0.76 false 0.583,1.677 0.896,1.833 0.313,0.156 10 false *a 6.385,1.688 6.698,1.844 0.313,0.156 10 false *a 0.083,0.177 0.396,0.333 0.313,0.156 10 false *A 4,0.177 4.313,0.333 0.313,0.156 10 false *B
*A Front Side *B Rear Side
*a Guide Pin - -



ii.

Fix the carbon fiber reinforced plastic roof panel using vice grips.

NOTICE:

To prevent damage to the carbon roof, insert a cloth between the vise grip and the roof.


K159023C01
4.094,4.979 4.365,4.417 4.365,4.417 4.531,4.417 false 3.021,5.156 2.76,4.656 2.76,4.656 2.594,4.656 false 3.448,0.844 4.667,0.167 false 1.833,4.083 2,4.083 2,4.083 2.115,3.427 false 4.667,4 3.448,3.375 false 2.115,0.781 2,0.167 2,0.167 1.833,0.167 false 4.833,4 4.667,4 4.667,4 5.344,3.302 false 5.344,0.927 4.667,0.167 4.667,0.167 4.833,0.167 false 4.594,4.365 4.906,4.521 0.313,0.156 10 false *1 2.406,4.615 2.719,4.771 0.313,0.156 10 false *2 1.646,0.083 1.958,0.24 0.313,0.156 10 false *a 1.646,4.01 1.958,4.167 0.313,0.156 10 false *a 4.938,3.927 5.25,4.083 0.313,0.156 10 false *a 4.906,0.073 5.219,0.229 0.313,0.156 10 false *a
*1 ROOF PANEL *2 ROOF SIDE PANEL
*a Vice Grip Fixing Position - -



iii.

Install the roof panel support.

K160371C01
6.354,2.354 6.333,1.667 6.333,1.667 6.167,1.667 false 6.604,2.667 6.5,3.25 6.5,3.25 6.667,3.25 false 6,1.615 6.313,1.771 0.313,0.156 10 false *1 6.729,3.177 6.979,3.438 0.25,0.26 10 false *2
*1 ROOF PANEL SUPPORT *2 RIVETS



iv.

Install the rivets.


v.

Remove the adhesive protruded from the carbon fiber reinforced plastic roof panel before it hardens.


vi.

Remove the masking tape before the adhesive hardens.



q.

Dry and harden the adhesive.

i.

Harden the adhesive completely.

HINT:
·

With dryer or equivalent (60°C): 60 minutes (complete hardening: 90 minutes)

·

Ambient temperature (25°C): 12 hours (complete hardening: 24 hours)





r.

Primer surfacer application

i.

Apply primer to the exposed areas on the top surface of the carbon fiber reinforced plastic roof.

NOTICE:
·

For the film specification, apply primer to the areas where the substrate is exposed from the film on the top surface of the carbon fiber reinforced plastic roof so that water does not adhere directly to the substrate in order to prevent galvanic corrosion.

·

If the flange on the top surface of the roof is damaged, apply primer surfacer to the areas where the substrate is exposed.



K159975C01
0.167,0.167 7,2.583 6.833,2.417 2.073,1.021 2.25,0.5 2.25,0.5 2.417,0.5 false 5.5,1.135 5.667,0.583 5.667,0.583 5.833,0.583 false 1.052,1.094 1,0.625 1,0.625 0.833,0.625 false 0.5,1.75 0.667,1.75 0.667,1.75 0.938,1.208 false 2.927,2.094 2.76,2.094 2.76,2.094 2.594,1.646 false 4,1.833 4.167,1.833 4.167,1.833 4.313,1.302 false 4.531,1.208 4.448,0.708 4.448,0.708 4.281,0.708 false 6.438,2.167 6.271,2.167 6.271,2.167 6.063,1.688 false 3.583,2.583 3.583,0.167 false 0.25,0.25 0.563,0.406 0.313,0.156 10 false *A 3.688,0.26 4,0.417 0.313,0.156 10 false *B 0.302,1.698 0.615,1.854 0.313,0.156 10 false *1 6.5,2.094 6.813,2.25 0.313,0.156 10 false *2 0.635,0.563 0.948,0.719 0.313,0.156 10 false *3 4.094,0.646 4.406,0.802 0.313,0.156 10 false *4 2.469,0.438 2.781,0.594 0.313,0.156 10 false *5 1.792,1.427 2.104,1.583 0.313,0.156 10 false *a 5.229,1.521 5.542,1.677 0.313,0.156 10 false *a 5.896,0.51 6.208,0.667 0.313,0.156 10 false *5 3.813,1.771 4.125,1.927 0.313,0.156 10 false *1 2.979,2.01 3.292,2.167 0.313,0.156 10 false *2 4.094,2.292 4.406,2.448 0.313,0.156 10 false *b
*A Film Specification *B Painted Specification
*1 CARBON FIBER REINFORCED PLASTIC ROOF *2 ROOF SIDE PANEL
*3 ROOF FILM *4 Clear
*5 ROOF DRIP SIDE MOULDING - -
*a Primer surfacer application area *b Damage
K108837

Adhesive - -




s.
K159024C01
0.917,2.417 1.25,1.75 false 0.75,2.417 0.917,2.417 0.917,2.417 1.667,2.167 false 1.417,3.083 1.667,2.75 1.667,2.75 1.833,2.75 false 2.417,3.25 2.583,3 2.583,3 2.75,3 false 1.167,3.917 1.333,3.917 1.333,3.917 1.51,3.552 false 0.563,2.344 0.875,2.5 0.313,0.156 10 false *b 2.802,2.948 3.115,3.104 0.313,0.156 10 false *b 1.875,2.688 2.188,2.844 0.313,0.156 10 false *b 0.99,3.833 1.302,3.99 0.313,0.156 10 false *a
*b Masking
K108837

Adhesive


Finish-apply adhesive.

i.

After the adhesive of the area *a has hardened, mask the outer panels including vertical surfaces of the left and right roof side rails again.


ii.
K159025C01
0.792,2.146 0.958,2.146 0.958,2.146 1.208,1.771 false 2.594,2.75 2.427,2.75 2.427,2.75 2.594,2.333 false 1.417,3.083 1.333,2.667 1.333,2.667 1.167,2.667 false 2.083,3.5 2,2.833 2,2.833 1.833,2.833 false 2.5,3.281 2.667,3 2.667,3 2.833,3 false 0.615,2.073 0.927,2.229 0.313,0.156 10 false *b 2.667,2.688 2.979,2.844 0.313,0.156 10 false *b 0.99,2.604 1.302,2.76 0.313,0.156 10 false *b 2.875,2.938 3.188,3.094 0.313,0.156 10 false *b 1.646,2.75 1.958,2.906 0.313,0.156 10 false *a
*b Masking
K108837

Adhesive


Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115) to the *a.


iii.
K159026C01
0,0 0,0 false
K108837

Adhesive


Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115) on the front and back flanges of the carbon fiber reinforced plastic roof panel and the body.


iv.
K159027C01
0,0 0,0 false
K108837

Adhesive


Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115) to the rivets.


v.

Make the adhesive uniform.

K159028C01
2.021,3.333 1.667,2.75 1.667,2.75 1.5,2.75 false 5.188,3.177 5.417,2.667 5.417,2.667 5.583,2.667 false 5.948,3.292 6.333,2.833 6.333,2.833 6.5,2.833 false 5.646,2.615 5.958,2.771 0.313,0.156 10 false *a 6.594,2.781 6.906,2.938 0.313,0.156 10 false *a 1.323,2.688 1.635,2.844 0.313,0.156 10 false *a
*a Masking - -
K108837

Adhesive - -



vi.
K159029C01
0.875,1.792 1.042,1.792 1.042,1.792 1.125,1.5 false 3.063,1.427 2.896,1.427 2.896,1.427 2.813,1.031 false 0.688,1.708 1,1.865 0.313,0.156 10 false *a 3.115,1.375 3.427,1.531 0.313,0.156 10 false *a
*a Masking


Remove the masking tape before the adhesive dries.


vii.

Make the adhesive uniform.



t.

Dry and harden the adhesive.

i.

Harden the adhesive completely.

HINT:
·

With dryer or equivalent (60°C): 60 minutes (complete hardening: 90 minutes)

·

Ambient temperature (25°C): 12 hours (complete hardening: 24 hours)