Refer to the TOYOTA Repair Manual for adjustment method.
Vehicle Exterior > DOOR / HATCH
INSPECT HOOD SUB-ASSEMBLY
Check that the clearance measurements of areas "A" through "E" are within each standard range.
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 2.0 to 6.0 mm (0.0787 to 0.236 in.) | B | 2.0 to 6.0 mm (0.0787 to 0.236 in.) |
| C | 4.9 to 8.9 mm (0.193 to 0.350 in.) | D | 2.3 to 5.3 mm (0.0906 to 0.209 in.) |
| E | 11 mm (0.433 in.) | - | - |
Centering bolts are used to install the hood hinges and hood lock. The hood and hood lock cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts with washers when making adjustments.
INSPECT FRONT DOOR PANEL SUB-ASSEMBLY (for 5 Door)
Check that the clearance measurements of areas "A" to "N" are within the standard ranges.
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 3.5 to 6.5 mm (0.138 to 0.256 in.) | B | -1.5 to 1.5 mm (-0.0591 to 0.0591 in.) |
| C | 3.5 to 6.5 mm (0.138 to 0.256 in.) | D | 1.2 to 5.2 mm (0.0472 to 0.205 in.) |
| E | 3.5 to 6.5 mm (0.138 to 0.256 in.) | F | 1.1 to 5.1 mm (0.0433 to 0.201 in.) |
| G | 3.0 to 6.0 mm (0.118 to 0.236 in.) | H | -1.5 to 1.5 mm (-0.0591 to 0.0591 in.) |
| I | 6.4 mm (0.252 in.) | J | 3.5 mm (0.138 in.) |
| K | 6.0 mm (0.236 in.) | L | 3.2 mm (0.126 in.) |
| M | 3.8 to 6.2 mm (0.150 to 0.244 in.) | N | -1.2 to 1.2 mm (-0.0472 to 0.0472 in.) |
Use the same procedure for the LH side and RH side.
The following procedure is for the LH side.
Centering bolts are used to install the door hinges to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.
INSPECT FRONT DOOR PANEL SUB-ASSEMBLY (for 3 Door)
Check that the clearance measurements of areas "A" to "D" are within the standard ranges.
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 3.3 to 5.7 mm (0.130 to 0.224 in.) | B | 2.8 to 5.8 mm (0.110 to 0.228 in.) |
| C | -1.2 to 1.2 mm (-0.0472 to 0.0472 in.) | D | 0 mm (0 in.) |
Use the same procedure for the LH side and RH side.
The following procedure is for the LH side.
Centering bolts are used to install the door hinges to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.
INSPECT REAR DOOR PANEL SUB-ASSEMBLY
Check that the clearance measurements of areas "A" to "M" are within the standard ranges.
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 2.8 to 5.8 mm (0.110 to 0.228 in.) | B | 3.3 to 6.3 mm (0.130 to 0.248 in.) |
| C | 1.2 to 5.2 mm (0.0472 to 0.205 in.) | D | 3.5 to 6.5 mm (0.138 to 0.256 in.) |
| E | 1.2 to 5.2 mm (0.0472 to 0.205 in.) | F | 3.5 to 6.5 mm (0.138 to 0.256 in.) |
| G | -1.5 to 1.5 mm (-0.0591 to 0.0591 in.) | H | 3.8 to 6.2 mm (0.150 to 0.244 in.) |
| I | -1.2 to 1.2 mm (-0.0472 to 0.0472 in.) | J | 6.0 mm (0.236 in.) |
| K | 2.8 mm (0.110 in.) | L | 2.8 to 5.8 mm (0.110 to 0.228 in.) |
| M | -1.5 to 1.5 mm (-0.0591 to 0.0591 in.) | - | - |
Use the same procedure for the LH side and RH side.
The following procedure is for the LH side.
Centering bolts are used to install the door hinges to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.
INSPECT BACK DOOR PANEL SUB-ASSEMBLY
Check that the clearance measurements of areas "A" to "K" are within the standard ranges.
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 6.0 to 9.0 mm (0.236 to 0.354 in.) | B | -0.5 to 2.5 mm (-0.0197 to 0.098 in.) |
| C | 6.0 to 9.0 mm (0.236 to 0.354 in.) | D | -0.5 to 2.5 mm (-0.0197 to 0.098 in.) |
| E | 3.0 to 8.0 mm (0.118 to 0.315 in.) | F | 4.8 to 7.8 mm (0.189 to 0.307 in.) |
| G | 4.9 to 8.9 mm (0.193 to 0.350 in.) | H | 3.1 to 8.1 mm (0.122 to 0.319 in.) |
| I | 3.5 to 8.5 mm (0.138 to 0.335 in.) | J | 3.5 to 8.5 mm (0.138 to 0.335 in.) |
| K | 4.2 to 9.2 mm (0.165 to 0.362 in.) | - | - |
Centering bolts are used to install the door hinges to the door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts (with washers) when making adjustments.