Home › Vehicle Exterior › BODY PANEL › CENTER BODY PILLAR (for TMC Made 5 Door) › from 2021.04
BM36W0E _01 Vehicle Exterior _088117 BODY PANEL _0449289 CENTER BODY PILLAR(for TMC Made 5 Door) F

BODY PANEL  CENTER BODY PILLAR(for TMC Made 5 Door)  CUT AND JOIN REPLACEMENT SECTIONS  


K156371

REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108826

Cut with Disc Sander etc.
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts

a.

Do not butt weld or heat repair because the heat decreases the strength of areas where ultra high strength steel is used. (See the introduction)


b.

Remove the center body pillar outer.

K156293C01
5.042,0.76 5.354,0.917 0.313,0.156 10 false *a
*a 20 mm (0.79 in.) - -


K158499C01
3.26,4.427 3.094,4.427 3.094,4.427 3.031,3.917 false 3.313,4.333 3.625,4.49 0.313,0.156 10 false *1 2.365,3.167 2.677,3.323 0.313,0.156 10 false *a
*1 CENTER BODY PILLAR OUTER - -
*a 160 mm (6.30 in.) - -


K158501

K156331


c.

Remove the center body pillar reinforcement sub-assembly.

K158514C01
3.708,2.625 3.333,2.25 3.333,2.25 3.167,2.25 false 2.979,2.167 3.292,2.323 0.313,0.156 10 false *1
*1 CENTER BODY PILLAR REINFORCEMENT SUB-ASSEMBLY - -


K158502

K161481


d.

After removing the A, remove the center body pillar reinforce sub-assembly lower.

K156298C01
5.25,2.479 5,2.083 5,2.083 4.833,2.083 false 1.979,3.208 2.917,2.75 2.917,2.75 3.083,2.75 false 4.646,2 4.958,2.156 0.313,0.156 10 false *1 3.146,2.688 3.302,2.885 0.156,0.198 10 false A 6.75,0.958 7.063,1.115 0.313,0.156 10 false *a 3.969,3.5 4.281,3.656 0.313,0.156 10 false *b
*1 CENTER BODY PILLAR REINFORCE SUB-ASSEMBLY LOWER - -
*a 20 mm (0.79 in.) *b 55 mm (2.17 in.)




INSTALLATION


Symbol Meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108823

Plug Weld
K108824

Plug Weld
K108827

Cut and Join Location
K108830

Fillet Weld
K108831

Butt Weld

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

If the entire supply part is not needed, remove the part of the supply part that is needed.

HINT:

A is reused.


K156300C01
1.698,2.156 1.5,1.75 1.5,1.75 1.333,1.75 false 1.979,3.219 2.417,2.833 2.417,2.833 2.583,2.833 false 1.146,1.667 1.458,1.823 0.313,0.156 10 false *1 4.813,0.833 5.125,0.99 0.313,0.156 10 false *a 4.229,3.375 4.542,3.531 0.313,0.156 10 false *b 2.667,2.771 2.823,2.969 0.156,0.198 10 false A
*1 CENTER BODY PILLAR REINFORCE SUB-ASSEMBLY LOWER - -
*a 20 mm (0.79 in.) *b 55 mm (2.17 in.)



d.

After welding the center body pillar reinforce sub-assembly lower to the vehicle, install the A.

K156299C01
1.667,2.469 1.417,2.167 1.417,2.167 1.25,2.167 false 5.594,3.198 6.417,2.833 6.417,2.833 6.583,2.833 false 1.063,2.094 1.375,2.25 0.313,0.156 10 false *1 6.656,2.781 6.813,2.979 0.156,0.198 10 false A
*1 CENTER BODY PILLAR REINFORCE SUB-ASSEMBLY LOWER - -



e.

Weld the center body pillar reinforcement sub-assembly to the vehicle side.

K158515C01
3.698,2.635 3.333,2.25 3.333,2.25 3.167,2.25 false 2.979,2.156 3.292,2.313 0.313,0.156 10 false *1
*1 CENTER BODY PILLAR REINFORCEMENT SUB-ASSEMBLY - -
*a Ultra High Strength Steel Welding Point - -


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 2 panels together including 1500 MPa ultra high strength steel.

*a: Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-6/ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar + CO2 20 to 30% or Ar + O2 2%) as the shield gas when plug welding. Sufficient weld strength cannot be assured when using 100% CO2 shield gas.



K158503C01
2.698,2.583 3.531,2.833 0.833,0.25 3.104,3.167 3.104,2.833 false 2.625,3.479 2.938,3.635 0.313,0.156 10 false *a 4.74,3.479 5.052,3.635 0.313,0.156 10 false *a 2.76,2.625 3.594,2.823 0.833,0.198 10 false 32 (326, 24)
*a 35.8 mm (1.41 in.) - -
V100146

N*m (kgf*cm, ft.*lbf) : Specified torque - -


K161483C01
2.229,1.813 2.542,1.969 0.313,0.156 10 false *a
*a 31 mm (1.22 in.) - -



f.

Weld the center body pillar outer to the vehicle side.

K158500C01
3.25,4.417 3.083,4.417 3.083,4.417 3,3.917 false 3.313,4.333 3.625,4.49 0.313,0.156 10 false *1
*1 CENTER BODY PILLAR OUTER - -
*a Ultra High Strength Steel Welding Point - -


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 3 panels or more together including 1500 MPa ultra high strength steel. (When plug welding a third panel to 2 panels which are welded under the conditions described above.)

*a: Plug weld Plug diameter Same as the standard method (See the introduction)
Wire type AWS A5.18 ER70S-6/ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar + CO2 20 to 30% or Ar + O2 2%) as the shield gas when plug welding. Sufficient weld strength cannot be assured when using 100% CO2 shield gas.



K158501C01
2.26,4.375 3.094,4.625 0.833,0.25 3.094,4.49 3.427,4.49 false 2.313,4.417 3.146,4.615 0.833,0.198 10 false 32 (326, 24)
V100146

N*m (kgf*cm, ft.*lbf) : Specified torque - -



g.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting/coating)


h.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


i.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.