Home › Vehicle Exterior › BODY PANEL › ROCKER PANEL (for 5 Door) › from 2021.04
BM36W0E _01 Vehicle Exterior _088117 BODY PANEL _0449291 ROCKER PANEL(for 5 Door) F

BODY PANEL  ROCKER PANEL(for 5 Door)  CUT AND JOIN REPLACEMENT SECTIONS  


K156373

With the front body pillar cut and join replacement sections (pattern 1) and quarter panel cut and join replacement sections (small areas) removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108820

Remove Weld Points
K108826

Cut with Disc Sander etc.
K108827

Cut and Join Location

a.

Do not butt weld or heat repair because the heat decreases the strength of areas where ultra high strength steel is used. (See the introduction)


b.

Remove the center body pillar outer.

K158509C01
2.01,3.729 1.833,3.25 1.833,3.25 1.667,3.25 false 1.479,3.177 1.792,3.333 0.313,0.156 10 false *1 4.281,3.24 4.594,3.396 0.313,0.156 10 false *a
*1 CENTER BODY PILLAR OUTER - -
*a 100 mm (3.94 in.) - -


K158511

K156333


c.

Remove the rocker reinforce sub-assembly outer and step plate sub-assembly lower.

K156305C01
2.083,4.604 1.917,4.604 1.917,4.604 1.844,4.052 false 6,4.615 5.833,4.615 5.833,4.615 5.708,4.063 false 2.156,4.531 2.469,4.688 0.313,0.156 10 false *1 6.063,4.552 6.375,4.708 0.313,0.156 10 false *2
*1 ROCKER REINFORCE SUB-ASSEMBLY OUTER *2 STEP PLATE SUB-ASSEMBLY LOWER


K158518

K158512

K161485



INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108824

Plug Weld
K108825

Plug Weld
K108830

Fillet Weld
K108831

Butt Weld

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

Before temporarily installing the new parts, weld the rocker reinforce sub-assembly outer and step plate sub-assembly lower with the standard number of welding points.

K157670C01
2.917,1.25 2.75,1.25 2.75,1.25 2.677,1.771 false 5.917,0.667 5.75,0.667 5.75,0.667 5.677,1.198 false 2.979,1.167 3.292,1.323 0.313,0.156 10 false *1 5.979,0.583 6.292,0.74 0.313,0.156 10 false *2
*1 ROCKER REINFORCE SUB-ASSEMBLY OUTER *2 STEP PLATE SUB-ASSEMBLY LOWER
*a Ultra High Strength Steel Welding Point - -


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 2 panels together including 1180 MPa ultra high strength steel.

*a: Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-6/ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar + CO2 20 to 30% or Ar + O2 2%) as the shield gas when plug welding. Sufficient weld strength cannot be assured when using 100% CO2 shield gas.




d.

Weld the rocker reinforce sub-assembly outer and step plate sub-assembly lower to the vehicle side.

K158519C01
2.083,4.667 1.917,4.667 1.917,4.667 1.833,4.104 false 6,4.667 5.833,4.667 5.833,4.667 5.708,4.104 false 2.146,4.573 2.458,4.729 0.313,0.156 10 false *1 6.063,4.583 6.375,4.74 0.313,0.156 10 false *2
*1 ROCKER REINFORCE SUB-ASSEMBLY OUTER *2 STEP PLATE SUB-ASSEMBLY LOWER
*a Ultra High Strength Steel Welding Point - -


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 2 panels together including 1500 MPa or 1180 MPa ultra high strength steel.

*a: Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-6/ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar + CO2 20 to 30% or Ar + O2 2%) as the shield gas when plug welding. Sufficient weld strength cannot be assured when using 100% CO2 shield gas.



K158513C01
1.385,1.438 2.219,1.688 0.833,0.25 1.833,1.938 1.833,1.688 false 1.26,2.125 1.573,2.281 0.313,0.156 10 false *a 4,1.979 4.313,2.135 0.313,0.156 10 false *a 1.448,1.479 2.281,1.677 0.833,0.198 10 false 32 (326, 24)
*a 35.8 mm (1.41 in.) - -
V100146

N*m (kgf*cm, ft.*lbf) : Specified torque - -


K161487C01
2.229,1.813 2.542,1.969 0.313,0.156 10 false *b 4.979,1.844 5.292,2 0.313,0.156 10 false *c
*a Ultra High Strength Steel Welding Point *b 31 mm (1.22 in.)
*c 15 mm (0.59 in.) - -


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 2 panels together including 1180 MPa ultra high strength steel.

*a: Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-6/ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar + CO2 20 to 30% or Ar + O2 2%) as the shield gas when plug welding. Sufficient weld strength cannot be assured when using 100% CO2 shield gas.




e.

Weld the center body pillar outer to the vehicle side.

K158510C01
2.01,3.729 1.917,3.25 1.917,3.25 1.75,3.25 false 1.563,3.177 1.875,3.333 0.313,0.156 10 false *1
*1 CENTER BODY PILLAR OUTER - -
*a Ultra High Strength Steel Welding Point - -


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 3 panels or more together including 1180 MPa ultra high strength steel. (When plug welding a third panel to 2 panels which are welded under the conditions described above.)

*a: Plug weld Plug diameter Same as the standard method (See the introduction)
Wire type AWS A5.18 ER70S-6/ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar + CO2 20 to 30% or Ar + O2 2%) as the shield gas when plug welding. Sufficient weld strength cannot be assured when using 100% CO2 shield gas.



K158511C01
2.354,4.354 3.188,4.604 0.833,0.25 3.188,4.479 3.438,4.479 false 2.417,4.406 3.25,4.604 0.833,0.198 10 false 32 (326, 24)
V100146

N*m (kgf*cm, ft.*lbf) : Specified torque - -



f.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting/coating)


g.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


h.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.