With the body lower back panel assembly removed.
REMOVAL
| Symbol Meaning | |
|---|---|
|
Remove Weld Points |
Remove the wheelhouse inner gusset front.
| *A | LH Side | *B | RH Side |
| *1 | WHEELHOUSE INNER GUSSET FRONT | - | - |
Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.
In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.
|
Adhesive | - | - |
| *A | LH Side | - | - |
| *A | RH Side | - | - |
INSTALLATION
| Symbol Meaning | |
|---|---|
|
Plug Weld |
Before temporarily installing the new parts, weld the rear floor pan, spare wheel clamp bracket, rear floor side panel and weld bolts with the standard number of welding points.
| *A | for Gasoline Model | *B | w/ Grand Spare Tire |
| *C | w/ Floor Under Cover | *D | Upper Face |
| *E | Lower Face | - | - |
| *1 | REAR FLOOR PAN | *2 | SPARE WHEEL CLAMP BRACKET |
| *3 | REAR FLOOR SIDE PANEL | *4 | WELD BOLTS |
Before temporarily installing the new parts, weld the rear floor pan, spare wheel clamp bracket, rear floor side panel and weld bolts with the standard number of welding points.
| *A | for Gasoline Model | *B | w/ Grand Spare Tire |
| *C | w/o Floor Under Cover | *D | Upper Face |
| *E | Lower Face | - | - |
| *1 | REAR FLOOR PAN | *2 | SPARE WHEEL CLAMP BRACKET |
| *3 | REAR FLOOR SIDE PANEL | *4 | WELD BOLTS |
Before temporarily installing the new parts, weld the rear floor pan, rear floor side panel and weld bolts with the standard number of welding points.
| *A | for Gasoline Model | *B | w/o Grand Spare Tire |
| *C | w/ Floor Under Cover | *D | Upper Face |
| *E | Lower Face | - | - |
| *1 | REAR FLOOR PAN | *2 | REAR FLOOR SIDE PANEL |
| *3 | WELD BOLTS | - | - |
Before temporarily installing the new parts, weld the rear floor pan, rear floor side panel and weld bolts with the standard number of welding points.
| *A | for Gasoline Model | *B | w/o Grand Spare Tire |
| *C | w/o Floor Under Cover | *D | Upper Face |
| *E | Lower Face | - | - |
| *1 | REAR FLOOR PAN | *2 | REAR FLOOR SIDE PANEL |
| *3 | WELD BOLTS | - | - |
Before temporarily installing the new parts, weld the rear floor pan, spare wheel clamp bracket, rear floor side panel and weld bolts with the standard number of welding points.
| *A | for HV Model | *B | w/ Grand Spare Tire |
| *C | w/ Floor Under Cover | *D | Upper Face |
| *E | Lower Face | - | - |
| *1 | REAR FLOOR PAN | *2 | SPARE WHEEL CLAMP BRACKET |
| *3 | REAR FLOOR SIDE PANEL | *4 | WELD BOLTS |
Before temporarily installing the new parts, weld the rear floor pan, spare wheel clamp bracket, rear floor side panel and weld bolts with the standard number of welding points.
| *A | for HV Model | *B | w/ Grand Spare Tire |
| *C | w/o Floor Under Cover | *D | Upper Face |
| *E | Lower Face | - | - |
| *1 | REAR FLOOR PAN | *2 | SPARE WHEEL CLAMP BRACKET |
| *3 | REAR FLOOR SIDE PANEL | *4 | WELD BOLTS |
Before temporarily installing the new parts, weld the rear floor pan, rear floor side panel and weld bolts with the standard number of welding points.
| *A | for HV Model | *B | w/o Grand Spare Tire |
| *C | w/ Floor Under Cover | *D | Upper Face |
| *E | Lower Face | - | - |
| *1 | REAR FLOOR PAN | *2 | REAR FLOOR SIDE PANEL |
| *3 | WELD BOLTS | - | - |
Before temporarily installing the new parts, weld the rear floor pan, rear floor side panel and weld bolts with the standard number of welding points.
| *A | for HV Model | *B | w/o Grand Spare Tire |
| *C | w/o Floor Under Cover | *D | Upper Face |
| *E | Lower Face | - | - |
| *1 | REAR FLOOR PAN | *2 | REAR FLOOR SIDE PANEL |
| *3 | WELD BOLTS | - | - |
Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).
Do not apply adhesive around the plug welding points.
Minimize squeeze out in plug welding areas.
|
Adhesive | - | - |
| *A | LH Side | - | - |
| *A | RH Side | - | - |
Weld the wheelhouse inner gusset front to the vehicle side.
| *A | LH Side | *B | RH Side |
| *1 | WHEELHOUSE INNER GUSSET FRONT | - | - |
After welding, apply body sealer and undercoating to the corresponding parts. (See the painting /coating)
After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.