OPERATION
Warning Indication
The combination meter assembly uses the multi-information display, PCS warning light and buzzer to provide the driver with pre-collision system malfunction and indications.
| *1 | Combination Meter Assembly
·
Buzzer |
- | - |
| *a | VSC OFF Indicator Light | *b | PCS Warning Light |
| *c | Multi-information Display | - | - |
| *1 | Combination Meter Assembly
·
Buzzer |
- | - |
| *a | VSC OFF Indicator Light | *b | PCS Warning Light |
| *c | Multi-information Display | - | - |
Pre-collision System Operation Status Display
If the forward recognition camera determines that the possibility of a collision is high, it sends a signal to the combination meter assembly and headup display (meter mirror sub-assembly)*. Upon receiving this signal, the combination meter assembly and headup display (meter mirror sub-assembly)* indicates a warning using the multi-information display, headup display (meter mirror sub-assembly)* and buzzer.
*: Models with headup display
| Multi-information Display
Headup Display (Meter Mirror Sub-assembly)* |
PCS Warning Light | Buzzer |
|---|---|---|
|
*: Models with headup display |
||
| BRAKE! | Does not illuminate | Sounds continuously |
Indicator Display when Pre-collision System Off
When the pre-collision system is turned off in the settings menu of the multi-information display, the PCS warning light in the combination meter assembly illuminates and a message is displayed on the multi-information display.
| Multi-information Display | PCS Warning Light |
|---|---|
| Pre-Collision System OFF | Illuminates |
When pre-collision braking assist and pre-collision braking operation are turned off using the VSC OFF switch, the VSC OFF indicator light and PCS warning light in the combination meter assembly illuminate, and a message is displayed on the multi-information display.
| Multi-information Display | VSC OFF Indicator Light | PCS Warning Light |
|---|---|---|
| VSC Turned OFF Pre-Collision Brake System Unavailable | Illuminates | Illuminates |
Pre-collision System Warning Display
When the system is not available, the following warning occurs to warn the driver.
| Multi-information Display | Detail | PCS Warning Light | Buzzer |
|---|---|---|---|
| Pre-Collision System Malfunction Visit Your Dealer | This message appears when the forward recognition camera detects a system malfunction | Illuminates | Sounds once |
| Pre-Collision System Unavailable See Owner's Manual | ·
Millimeter wave radar sensor assembly low voltage malfunction ·
Other millimeter wave radar sensor assembly malfunction |
Illuminates | - |
| Pre-Collision System Out of Temperature Range Unavailable See Owner's Manual | Millimeter wave radar sensor assembly temperature malfunction | Illuminates | - |
| Pre-Collision System Radar Sensor Blocked Unavailable Clean Radar Sensor | Dirty center mark of upper radiator grille or millimeter wave radar sensor assembly | Illuminates | - |
| Pre-Collision System Radar In Self Calibration Unavailable See Owner's Manual | Millimeter wave radar sensor assembly misaligned | Illuminates | - |
| Front Camera Unavailable See Owner's Manual | ·
Abnormal forward recognition camera voltage ·
Other forward recognition camera malfunction |
Illuminates | - |
| Front Camera Out of Temperature Range Unavailable Wait until Normal Temperature | Forward recognition camera temperature outside of operational range | Illuminates | - |
| Front Camera Low Visibility Unavailable See Owner's Manual | Dirty or fogged windshield glass over the forward recognition camera | Illuminates | - |
Changing Settings of Pre-collision System
Enabling/disabling the pre-collision system
The pre-collision system can be enabled/disabled on setting display screen of the multi-information display.
When the pre-collision system has been disabled using this setting, it will automatically be re-enabled after the ignition switch has been turned off and then back to ON (IG) again.
If the system is disabled, the PCS warning light will turn on and a message will be displayed on the multi-information display.
| *a | Steering Pad Switch Assembly | *b | PCS Warning Light |
| *c | Multi-information Display | - | - |
Changing the pre-collision warning timing
The pre-collision warning timing can be changed on setting display screen of the multi-information display.
The warning timing setting is retained when the ignition switch is turned off. However, if the pre-collision system is disabled and re-enabled, the operation timing will return to the default setting (middle).
| *a | Early | *b | Middle (This is the default setting.) |
| *c | Late | *d | Steering Pad Switch Assembly |