OUTLINE
Toyota Safety Sense
The Toyota Safety Sense consists of the following drive assist systems and contributes to a safe and comfortable driving experience:
PCS (Pre-Collision System)
LTA (Lane Tracing Assist)
Automatic High Beam
RSA (Road Sign Assist)
Dynamic Radar Cruise Control
PCS (Pre-Collision System)
The pre-collision system uses a radar sensor and front camera to detect objects in front of the vehicle. When the system determines that the possibility of a frontal collision with an object is high, a warning operates to urge the driver to take evasive action and the potential brake pressure is increased to help the driver avoid the collision. If the system determines that the possibility of a frontal collision with an object is extremely high, the brakes are automatically applied to help avoid the collision or help reduce the impact of the collision.
·
Vehicles ·
Bicyclists ·
Pedestrians |
PRECAUTION
Toyota Safety Sense
The Toyota Safety Sense is designed to operate under the assumption that the driver will drive safely, and is designed to help reduce the impact to the occupants and the vehicle in the case of a collision or assist the driver in normal driving conditions. As there is a limit to the degree of recognition accuracy and control performance that this system can provide, do not overly rely on this system. The driver is always responsible for paying attention to the vehicle's surroundings and driving safely.
Limitations of the pre-collision system
The driver is solely responsible for safe driving. Always drive safely, taking care to observe your surroundings. Do not use the pre-collision system instead of normal braking operations under any circumstances. This system will not prevent collisions or lessen collision damage or injury in every situation. Do not overly rely on this system. Failure to do so may lead to an accident, resulting in death or serious injury.
Although this system is designed to help avoid a collision or help reduce the impact of the collision, its effectiveness may change according to various conditions, therefore the system may not always be able to achieve the same level of performance. Read the following conditions carefully. Do not overly rely on this system and always drive carefully.
Do not attempt to test the operation of the pre-collision system yourself. Depending on the objects used for testing (dummies, cardboard objects imitating detectable objects, etc.), the system may not operate properly, possibly leading to an accident.
Pre-collision braking
When the pre-collision braking function is operating, a large amount of braking force will be applied.
If the vehicle is stopped by the operation of the pre-collision braking function, the pre-collision braking function operation will be canceled after approximately 2 seconds. Depress the brake pedal as necessary.
The pre-collision braking function may not operate if certain operations are performed by the driver. If the accelerator pedal is being depressed strongly or the steering wheel is being turned, the system may determine that the driver is taking evasive action and possibly prevent the pre-collision braking function from operating.
In some situations, while the pre-collision braking function is operating, operation of the function may be canceled if the accelerator pedal is depressed strongly or the steering wheel is turned and the system determines that the driver is taking evasive action.
If the brake pedal is being depressed, the system may determine that the driver is taking evasive action and possibly delay the operation timing of the pre-collision braking function.
When to disable the pre-collision system
In the following situations, disable the system, as it may not operate properly, possibly leading to an accident resulting in death or serious injury:
When the vehicle is being towed.
When your vehicle is towing another vehicle.
When transporting the vehicle via truck, boat, train or similar means of transportation.
When the vehicle is raised on a lift with the engine running (gasoline models)/hybrid system on (HV models) and the tires are allowed to rotate freely.
When inspecting the vehicle using a drum tester such as a chassis dynamometer or speedometer tester, or when using an on vehicle wheel balancer.
When a strong impact is applied to the front bumper or front grille, due to an accident or other reasons.
If the vehicle cannot be driven in a stable manner, such as when the vehicle has been in an accident or is malfunctioning.
When the vehicle is driven in a sporty manner or off-road.
When the tires are not properly inflated.
When the tires are very worn.
When tires of a size other than specified are installed.
When tire chains are installed.
When a compact spare tire or an emergency tire puncture repair kit is used.
If equipment (snow plow, etc.) that may obstruct the radar sensor or front camera is temporarily installed to the vehicle.
To avoid malfunction of the radar sensor
Observe the following precautions. Otherwise, the radar sensor may not operate properly, possibly leading to an accident resulting in death or serious injury.
Keep the radar sensor and the grille cover clean at all times.
| *1 | Radar Sensor | *2 | Grille Cover |
If the front of the radar sensor or the front or back of the grille cover is dirty or covered with water droplets, snow, etc., clean it.
Clean the radar sensor and grille cover with a soft cloth to avoid damaging them.
Do not attach accessories, stickers (including transparent stickers) or other items to the radar sensor, grille cover or surrounding area.
Do not subject the radar sensor or its surrounding area to a strong impact.
Do not disassemble the radar sensor.
Do not modify or paint the radar sensor or grille cover.
To avoid malfunction of the front camera
Observe the following precautions. Otherwise, the front camera may not operate properly, possibly leading to an accident resulting in death or serious injury.
Keep the windshield clean at all times.
If the windshield is dirty or covered with an oily film, water droplets, snow, etc., clean the windshield.
If a glass coating agent is applied to the windshield, it will still be necessary to use the windshield wipers to remove water droplets, etc. from the area of the windshield in front of the front camera.
Do not attach objects, such as stickers, transparent stickers, etc., to the outer side of the windshield in front of the front camera (shaded area in the illustration).
| *a | From the top of the windshield to approximately 1 cm (0.4 in.) below the bottom of the front camera. | *b | Approximately 20 cm (7.9 in.) (Approximately 10 cm (4.0 in.) to the right and left from the center of the front camera). |
If the part of the windshield in front of the front camera is fogged up or covered with condensation, or ice, use the windshield defogger to remove the fog, condensation, or ice.
If water droplets cannot be properly removed from the area of the windshield in front of the front camera by the windshield wipers, replace the wiper insert or wiper blade.
Do not attach window tint to the windshield.
Replace the windshield if it is damaged or cracked.
Do not allow liquids to contact the front camera.
Do not allow bright lights to shine into the front camera.
Do not dirty or damage the front camera.
When cleaning the inside of the windshield, do not allow glass cleaner to contact the lens of the front camera. Also, do not touch the lens.
Do not subject the front camera to a strong impact.
Do not change the installation position or direction of the front camera or remove it.
Do not disassemble the front camera.
Do not modify any components of the vehicle around the front camera (inside rear view mirror, etc.) or ceiling.
Do not attach any accessories to the hood, front grille or front bumper that may obstruct the front camera.
If a surfboard or other long object is to be mounted on the roof, make sure that it will not obstruct the front camera.
Do not modify the headlights or other lights.