FUNCTION OF MAIN COMPONENTS
The main components of the airbag system have the following functions:
| Component | Function | |
|---|---|---|
|
*1: HV models *2: Gasoline models |
||
| Airbag Sensor Assembly | ·
In the event of a frontal collision, the airbag sensor assembly receives the signal from either of the airbag sensor front or main sensor built into the airbag sensor assembly. The airbag sensor assembly receives the signal via its judgment circuit and also receives another signal from the safing sensor built into the airbag sensor assembly. After receiving signals from the safing sensor and at least one of the airbag sensor front and main sensor built into the airbag sensor assembly, the airbag sensor assembly determines whether the driver airbag, front passenger airbag and curtain shield airbags should be deployed, and the front seat belt pretensioners and rear seat belt pretensioners should be activated. The airbag sensor assembly also diagnoses system malfunctions. ·
In the event of a side or rear side collision, the airbag sensor assembly receives signals from the side airbag pressure sensor, No. 1 side airbag sensor or No. 2 side airbag sensor. The airbag sensor assembly receives the side airbag pressure sensor, No. 1 side airbag sensor or No. 2 side airbag sensor signal via its judgment circuit and also receives another signal from the No. 1 side airbag sensor or the safing sensor built into the airbag sensor assembly. After receiving signals from at least one of the side sensors and either of the safing sensors (No. 1 side airbag sensor or safing sensor built into the airbag sensor assembly), the airbag sensor assembly determines whether the front seat airbag, front seat center airbag and curtain shield airbags should be deployed, and the front seat belt pretensioners and rear seat belt pretensioners should be activated. The airbag sensor assembly also diagnoses system malfunctions. ·
Sends the collision detection signal to the ECM through the Controller Area Network (CAN) to operate fuel pump control.*2 ·
Sends the collision detection signal to the hybrid vehicle control ECU to shut down the hybrid system power supply.*1 ·
Sends a signal indicating a collision has occurred to the main body ECU (multiplex network body ECU) via CAN communication to illuminate the interior lights. ·
Sends the brake control request signal to the skid control ECU through the Controller Area Network (CAN) to operate the secondary collision brake. ·
Sends a signal indicating a collision has occurred to the combination meter assembly via CAN communication to flash the hazard lights. ·
Sends collision detection signals to the forward recognition camera to determine if the millimeter wave radar sensor assembly is misaligned. ·
Prepares the seat belt pretensioners to operate when the PCS (Pre-Collision System) determines that the possibility of a collision with another vehicle is high. |
|
| Horn Button Assembly | Used as supplements to the seat belts to help reduce impact to the occupants. | |
| Instrument Panel Passenger without Door Airbag Assembly | ||
| Front Seat Airbag Assembly LH/RH | ||
| Front Seat Center Airbag Assembly LH/RH | ||
| Curtain Shield Airbag Assembly LH/RH | ||
| Spiral Cable Sub-assembly | Transmits ignition signals from the airbag sensor assembly to the SRS driver airbag. | |
| Airbag Sensor Front LH/RH | Based on the deceleration of the vehicle during a frontal collision, distortion is created in the sensor and is converted into an electrical signal. | |
| Side Airbag Pressure Sensor LH/RH | Detects deformation of the front doors during a side collision using the pressure sensor and sends signals for the airbag sensor assembly to determine if deployment of SRS components is necessary. | |
| No. 1 Side Airbag Sensor LH/RH | Based on the deceleration of the vehicle during a side or rear side collision, distortion is created in the sensor and is converted into an electrical signal. | |
| No. 2 Side Airbag Sensor LH/RH | Based on the deceleration of the vehicle during a rear side collision, distortion is created in the sensor and is converted into an electrical signal. | |
| Front Seat Outer Belt Assembly LH/RH | Used to help reduce impact to the occupants. | |
| Rear Seat Outer Belt Assembly LH/RH | ||
| Hybrid Vehicle Control ECU*1 | Receives the collision detection signal from the airbag sensor assembly during a collision and shuts down the hybrid system power supply by turning the System Main Relays (SMRs) off, in order to ensure safety. | |
| ECM*2 | Receives the collision detection signal from the airbag sensor assembly and stops the fuel pump. | |
| Main Body ECU (Multiplex Network Body ECU) | Illuminates the interior lighting after receiving a collision detection signal from the airbag sensor assembly. | |
| Brake Booster with Master Cylinder Assembly*1 | Skid Control ECU | Receives the brake control request signal from the airbag sensor assembly, and sends brake control signals to the skid control ECU to reduce damage of the secondary collision. |
| Brake Actuator Assembly*2 | ||
| Combination Meter Assembly | SRS Warning Light | Turns on to alert the driver when the airbag sensor assembly detects a malfunction in the airbag system. |
| Multi-information Display | Displays a warning message to inform the driver of a malfunction in the airbag system. | |
| Buzzer | Sounds to warn the driver of a malfunction in the airbag system. | |
| hazard lights | Flashes the hazard lights after receiving a collision detection signal from the airbag sensor assembly. | |
| Forward Recognition Camera | Detects vehicles, pedestrians and bicycles in front of the vehicle and sends detection information to the airbag sensor assembly via CAN communication. | |
| Millimeter Wave Radar Sensor Assembly | Radiates millimeter wave radar forward, uses the reflected millimeter waves for detecting the presence of a vehicle ahead, the vehicle-to-vehicle distance, and the relative speed, and then transmits this information to the forward recognition camera. | |
| Network Gateway ECU | Relays the signal between the CAN communication lines. | |
SYSTEM CONTROL
Airbag for Frontal Collision
There are 3 airbags which deploy in the event of a frontal collision: the horn button assembly, instrument panel passenger without door airbag assembly and curtain shield airbag assemblies. These airbags deploy simultaneously. In addition, each front pretensioner contained in a front seat outer belt assembly, and each rear pretensioner contained in a rear seat outer belt assembly are also activated.
For a frontal collision, if an airbag sensor front detects an impact, it informs the airbag sensor assembly. The airbag sensor assembly causes the horn button assembly, instrument panel passenger without door airbag assembly and curtain shield airbag assemblies to deploy. Additionally, the airbag sensor assembly activates the seat belt pretensioners for the driver, front passenger and rear passengers.
Deceleration sensors used for the airbag system are installed on various parts on the vehicle and calculate the deceleration (or acceleration) rate of each part during a collision.
Depending on the situation, the airbag sensor assembly sends a deployment signal to each airbag and pretensioner based on the information from each sensor.
Frontal collision signals are produced based on the information from the airbag sensor assembly and airbag sensor front. Frontal collision signals are used to deploy all the airbags except all the side airbags and activate all the pretensioners as indicated in the table below.
Airbag for Side/Rear Side Collision
There are 3 airbags which deploy in the event of a severe side collision: the front seat airbag assembly, front seat center airbag assembly and curtain shield airbag assembly on the side of the collision. These airbags deploy simultaneously. Additionally, at the same time, the front seat belt pretensioners and rear seat belt pretensioners are also activated.
For a side collision, if the side airbag pressure sensor, No. 2 side airbag sensor and No. 1 side airbag sensor detect an impact, they inform the airbag sensor assembly, and the airbag sensor assembly causes the front seat airbag assembly, front seat center airbag assembly and curtain shield airbag assemblies to deploy simultaneously, and activate the front seat belt pretensioners and rear seat belt pretensioners.
If the severity of the collision is particularly high, the SRS curtain shield airbag on the side opposite the collision is deployed and the front and rear seat belt pretensioners on the side opposite the collision are activated.
The front seat airbag assembly, front seat center airbag assemblies and curtain shield airbag assemblies are deployed and each front pretensioner in a front seat outer belt assembly and each rear pretensioner in a rear seat outer belt assembly are activated based on signals from the side airbag pressure sensor, No. 1 side airbag sensor and airbag sensor assembly.
For a rear side collision, if the No. 2 side airbag sensor and No. 1 side airbag sensor detect an impact, they inform the airbag sensor assembly, and the airbag sensor assembly causes the curtain shield airbag assemblies to deploy simultaneously, and activate the rear seat belt pretensioner on the side of the collision.
The curtain shield airbag assemblies are deployed and each rear pretensioner in a rear seat outer belt assembly are activated based on signals from the No. 2 side airbag sensor, No. 1 side airbag sensor and airbag sensor assembly.
Primary Check Illumination Control
After the ignition switch is turned on (IG), the airbag sensor assembly illuminates the SRS warning light in the combination meter assembly for approximately 6 seconds and conducts the primary check. During the primary check, the ignition of airbags is prohibited and a diagnosis of the airbag sensor assembly is performed. If a malfunction is detected during the primary check, the SRS warning light will remain on even after 6 seconds have elapsed.
FAIL-SAFE
If the airbag sensor assembly detects a malfunction in the airbag system, the airbag sensor assembly illuminates the SRS warning light and displays the warning message on the multi-information display and sounds the buzzer to alert the driver of the malfunction.
DIAGNOSIS
If the airbag sensor assembly detects a malfunction in the airbag system, the airbag sensor assembly stores the malfunction data in memory as Diagnostic Trouble Codes (DTCs).
The airbag sensor assembly outputs malfunction data and 5-digit Diagnostic Trouble Codes (DTCs) to the GTS.
The 5-digit DTCs can be read by connecting the GTS to the DLC3. For details, refer to the Repair Manual.
If the SRS airbags deploy, the airbag sensor assembly will turn on the SRS warning light. However, unlike an ordinary malfunction, a DTC will not be stored. The SRS warning light cannot be manually turned off. It is necessary to replace the airbag sensor assembly with a new one.