OUTLINE
An automatic air conditioning system or a manual air conditioning system is available depending on the model.
An inside-and-outside dual air layer type air conditioning unit is used for the automatic air conditioning system.
HFC-134a refrigerant is used.
SPECIFICATION
Ventilation and Heater Core
|
*1: Models with automatic air conditioning system *2: Models with manual air conditioning system |
|||
| Heater Radiator Unit Sub-assembly | Type | Straight Flow Aluminum (SFA) - II | |
| Size (W x H x L) | mm (in.) | 180.7 x 120 x 27
(7.1 x 4.7 x 1.1) |
|
| Blower with Fan Motor Sub-assembly | Motor Type | DC Ferrite Brushless*1
DC*2 |
|
| Fan Type | Semi Sirocco | ||
| Fan Size (Dia. x H)*1 | mm (in.) | Upper Side: 122.0 x 55.0 (4.8 x 2.2)
Lower Side: 125.0 x 38.0 (4.9 x 1.5) |
|
| Fan Size (Dia. x H)*2 | mm (in.) | 137.0 x 70 (5.4 x 2.8) | |
Air Conditioning
|
*1: Gasoline models *2: HV models |
|||
| Cooler Condenser Assembly | Type | Global Inner-fin Condenser (GIC) | |
| Size (W x H x L) | mm (in.) | 530 x 376.2 x 11.5 (20.9 x 14.8 x 0.5)*1 | |
| 630 x 376.2 x 11.5 (24.8 x 14.8 x 0.5)*2 | |||
| Fin Pitch | mm (in.) | 2.5 (0.10) | |
| Cooler Compressor Assembly*1 | 5TSE10 | ||
| Compressor with Motor Assembly*2 | ESB20C | ||
| Refrigerant | Type | HFC-134a | |
| Evaporator | Type | Beneficial Refrigerant Stream (BRS) Evaporator | |
| Size (W x H x L) | mm (in.) | 199.3 x 231.0 x 38.0 (7.8 x 9.1 x 1.5) | |
| Fin Pitch | mm (in.) | 3.0 (0.12) | |
MAIN FEATURES
The air conditioning system has the following features:
|
*1: Models with automatic air conditioning system *2: Gasoline models |
|
| High Performance | ·
A high efficiency type clean air filter, which has a pollen removal effect, is used. Depending on models, an odor removal effect has been used on the clean air filter. ·
The blower control has 7 levels in manual mode and 31 levels in auto mode for more precise control.*1 ·
Neural network control is used so passengers can finely control the air conditioning for maximum comfort.*1 ·
Using the following features of the compressor (continuously variable capacity compressor), high cooling performance and a quiet cabin have been achieved:*2 -
Oil Separator -
Variable Suction Side Throttle -
Solenoid Valve with Built-in Crank Chamber to Suction Passage (CS) Valve |
| Lightweight | ·
An air conditioning harness assembly with a built-in communication/driver IC is used in a lightweight wire harness design to allow a reduced number of wires. ·
The use of this type of connector means that pulse pattern type servo motors can be used. |
| Compact | A blower motor with a built-in blower motor controller is used to achieve a compact construction.*1 |
| Others | The following parts are used to ensure high cooling performance while realizing a compact and lightweight construction.
·
Semi-center Location Air Conditioning Unit ·
Straight Flow Aluminum (SFA)-II Heater Radiator Sub-assembly ·
Global Inner-fin Condenser (GIC) Sub-cool Condenser ·
Beneficial Refrigerant Stream (BRS) Evaporator |