Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE CONTROL SYSTEM (for Gasoline Model) › 2020.03–2020.07
NM36W0E _54 Brake _088478 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0421634 BRAKE CONTROL SYSTEM(for Gasoline Model) DE DETAILS F

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE CONTROL SYSTEM(for Gasoline Model)  DETAILS  BRAKE ACTUATOR  


CONSTRUCTION


a.

The brake actuator and skid control ECU are integrated into the brake actuator assembly to reduce size and weight.


b.

The brake actuator controls the brake fluid pressure of each wheel cylinder and consists of the master cylinder pressure sensor, master cylinder cut solenoid valve, pressure holding solenoid valve, pressure reduction solenoid valve, pump motor, reservoir, etc.


c.

The solenoid relay, motor relay and motor cut relay are built into the skid control ECU.

X146169C01
1.417,0.833 1.583,0.833 1.583,0.833 2.25,1.5 true 4.896,1.583 5.5,0.917 5.5,0.917 5.667,0.917 true 1.219,0.74 1.531,0.896 0.313,0.156 10 false *a 5.76,0.833 6.073,0.99 0.313,0.156 10 false *b
*a Skid Control ECU *b Actuator Portion


Hydraulic Circuit (Not Operating)
X114908C02
2.583,0.865 2.74,0.865 2.74,0.865 2.927,0.635 true 0.573,1.365 0.5,1.042 0.5,1.042 0.375,1.042 true 3.417,4.115 3.417,3.854 3.417,3.854 3.094,3.667 true 3.719,4.115 3.719,3.854 3.719,3.854 4.073,3.646 true 3.281,6.208 3.281,5.688 true 3.875,6.198 3.875,5.677 true 2.417,0.792 2.729,0.948 0.313,0.156 10 false *1 0.188,0.969 0.5,1.125 0.313,0.156 10 false *2 3.448,1.781 3.76,1.938 0.313,0.156 10 false *3 0.792,2.604 1.104,2.76 0.313,0.156 10 false *4 6.208,2.604 6.521,2.76 0.313,0.156 10 false *5 1.063,3.771 1.375,3.927 0.313,0.156 10 false *6 3.354,4.177 3.667,4.333 0.313,0.156 10 false *7 3.208,6.25 3.521,6.406 0.313,0.156 10 false *9 1.052,6.469 1.521,6.625 0.469,0.156 10 false *a 2.292,6.469 2.76,6.625 0.469,0.156 10 false *b 4.729,6.469 5.198,6.625 0.469,0.156 10 false *c 5.938,6.458 6.406,6.615 0.469,0.156 10 false *d 2.26,3.781 2.573,3.938 0.313,0.156 10 false *6 4.74,3.771 5.052,3.927 0.313,0.156 10 false *6 5.927,3.771 6.24,3.927 0.313,0.156 10 false *6 1.073,4.958 1.385,5.115 0.313,0.156 10 false *8 2.25,4.958 2.563,5.115 0.313,0.156 10 false *8 4.729,4.948 5.042,5.104 0.313,0.156 10 false *8 5.927,4.958 6.24,5.115 0.313,0.156 10 false *8 3.646,4.177 3.958,4.333 0.313,0.156 10 false *7 3.792,6.25 4.104,6.406 0.313,0.156 10 false *9
*1 Brake Master Cylinder Sub-assembly *2 Brake Actuator
*3 Master Cylinder Pressure Sensor *4 No. 1 Master Cylinder Cut Solenoid Valve
*5 No. 2 Master Cylinder Cut Solenoid Valve *6 Pressure Holding Solenoid Valve
*7 Pump *8 Pressure Reduction Solenoid Valve
*9 Reservoir - -
*a Front Brake Caliper RH *b Rear Brake Caliper LH
*c Rear Brake Caliper RH *d Front Brake Caliper LH


i.

Pressure Holding Solenoid Valve and Pressure Reduction Solenoid Valve

·

The skid control ECU increases, holds or decreases the brake fluid pressure of each wheel cylinder by individually turning its pressure holding solenoid valve and pressure reduction solenoid valve on or off.



ii.

Master Cylinder Cut Solenoid Valve

·

A linear solenoid valve is used for the master cylinder cut solenoid valve, minimizing fluctuations in the brake fluid pressure during control.

·

The master cylinder cut solenoid valve is turned on or off to control the brake fluid pressure from the pump to the wheel cylinder.

X113254C01
0.292,0.208 2.5,3.594 2.208,3.385 2.792,0.208 6.906,3.594 4.115,3.385 3.667,0.458 4,0.708 0.333,0.25 5.844,0.479 6.177,0.729 0.333,0.25 0.656,0.615 0.969,0.771 0.313,0.156 10 false *1 1.99,1.573 2.302,1.729 0.313,0.156 10 false *2 0.604,2.094 0.917,2.25 0.313,0.156 10 false *3 1.385,2.708 1.698,2.865 0.313,0.156 10 false *4 6.042,3.365 6.354,3.521 0.313,0.156 10 false *5 0.344,0.271 0.656,0.427 0.313,0.156 10 false *a 2.854,0.271 3.167,0.427 0.313,0.156 10 false *b 3.75,0.521 4.063,0.677 0.313,0.156 10 false *c 5.938,0.542 6.25,0.698 0.313,0.156 10 false *d 4.49,1.573 4.802,1.729 0.313,0.156 10 false *2 6.625,1.583 6.938,1.74 0.313,0.156 10 false *2 3.885,2.688 4.198,2.844 0.313,0.156 10 false *4 6.042,2.698 6.354,2.854 0.313,0.156 10 false *4 1.375,3.375 1.688,3.531 0.313,0.156 10 false *5 3.885,3.365 4.198,3.521 0.313,0.156 10 false *5 3.156,0.615 3.469,0.771 0.313,0.156 10 false *1 5.302,0.615 5.615,0.771 0.313,0.156 10 false *1
*1 Master Cylinder *2 Pump
*3 Master Cylinder Cut Solenoid Valve *4 Pressure Holding Solenoid Valve
*5 Brake Caliper - -
*a Not Operating *b Operating
*c Required Brake Fluid Pressure: Low *d Required Brake Fluid Pressure: High




iii.

Master Cylinder Pressure Sensor

·

The master cylinder pressure sensor is built into the brake actuator and detects and outputs the brake fluid pressure from the master cylinder to the skid control ECU.





OPERATION


a.

ABS and EBD

i.

The ABS and EBD systems control the pump, pressure holding solenoid valve and pressure reduction valve to control the brake fluid pressure of each wheel cylinder.

X112181C01
0.677,0.135 2.531,3.719 1.854,3.583 2.698,0.125 4.552,3.708 1.854,3.583 4.76,0.115 6.615,3.698 1.854,3.583 1.219,1.833 1.313,1.833 1.313,1.833 1.51,1.313 true 1.177,3.313 1.281,3.313 1.281,3.313 1.51,2.771 true 0.74,0.146 1.021,0.323 0.281,0.177 10 false *a 2.771,0.156 3.156,0.333 0.385,0.177 10 false *b 4.823,0.135 5.125,0.333 0.302,0.198 10 false *c 0.938,0.802 1.302,0.99 0.365,0.188 10 false *1 2.979,0.792 3.292,0.979 0.313,0.188 10 false *1 5,0.802 5.333,1.031 0.333,0.229 10 false *1 0.958,2.292 1.375,2.51 0.417,0.219 10 false *2 2.948,2.313 3.271,2.552 0.323,0.24 10 false *2 4.979,2.302 5.365,2.531 0.385,0.229 10 false *2 2.115,3.49 2.448,3.646 0.333,0.156 10 false *e 1.042,1.76 1.333,1.927 0.292,0.167 10 false *g 1.01,3.25 1.375,3.438 0.365,0.188 10 false *f 4.979,1.875 5.375,2.073 0.396,0.198 10 false *d
*1 Pressure Holding Solenoid Valve *2 Pressure Reduction Solenoid Valve
*a Pressure Increase Mode *b Pressure Holding Mode
*c Pressure Reduction Mode *d To Reservoir
*e To Brake Caliper *f Port2
*g Port1 - -


ABS and EBD Operation
Pressure Mode Increase Mode Holding Mode Reduction Mode
Pressure Holding Solenoid Valve OFF (Open) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve OFF (Closed) OFF (Closed) ON (Open)
Port1 Open Closed Closed
Port2 Closed Closed Open
Wheel Cylinder Pressure Increases Holds Reduces



b.

Brake Assist

i.

Brake assist controls each pressure holding solenoid valve and pressure reduction solenoid valve to apply brake fluid pressure higher than that of the master cylinder from the pump of the brake actuator to each wheel cylinder.

Hydraulic Circuit
X114909C06
0.813,1.635 1.125,1.792 0.313,0.156 10 false *1 6.167,1.635 6.479,1.792 0.313,0.156 10 false *2 1.479,2.021 1.792,2.177 0.313,0.156 10 false *3 1.479,2.958 1.792,3.115 0.313,0.156 10 false *4 0.708,0.052 1.021,0.208 0.313,0.156 10 false *a 0.75,4.448 1.063,4.604 0.313,0.156 10 false *b 2.969,4.469 3.281,4.625 0.313,0.156 10 false *c 4.344,4.479 4.656,4.635 0.313,0.156 10 false *d 6.552,4.448 6.865,4.604 0.313,0.156 10 false *e 2.646,2.021 2.958,2.177 0.313,0.156 10 false *3 4.417,2.021 4.729,2.177 0.313,0.156 10 false *3 5.573,2.021 5.885,2.177 0.313,0.156 10 false *3 2.656,2.958 2.969,3.115 0.313,0.156 10 false *4 4.417,2.958 4.729,3.115 0.313,0.156 10 false *4 5.594,2.958 5.906,3.115 0.313,0.156 10 false *4 6.344,0.031 6.656,0.188 0.313,0.156 10 false *a
*1 No. 1 Master Cylinder Cut Solenoid Valve *2 No. 2 Master Cylinder Cut Solenoid Valve
*3 Pressure Holding Solenoid Valve *4 Pressure Reduction Solenoid Valve
*a From Brake Master Cylinder Sub-assembly *b To Front Brake Caliper RH
*c To Rear Brake Caliper LH *d To Rear Brake Caliper RH
*e To Front Brake Caliper LH - -


Brake Assist Operation
Brake Assist Not Activated Activated
No. 1 Master Cylinder Cut Solenoid Valve OFF (Open) ON*
No. 2 Master Cylinder Cut Solenoid Valve OFF (Open) ON*
Pressure Holding Solenoid Valve OFF (Open) OFF (Open)
Pressure Reduction Solenoid Valve OFF (Closed) OFF (Closed)
Wheel Cylinder Pressure Equivalent to Master Cylinder Brake Fluid Pressure Higher Pressure Required than Master Cylinder Brake Fluid Pressure

HINT:

*: The solenoid valve controls the brake fluid pressure by continually opening and closing the valve in accordance with the operating conditions.




c.

TRC

i.

TRC limits the drive force from the engine and controls each pressure holding solenoid valve and pressure reduction solenoid valve to apply more brake fluid pressure from the pump of the brake actuator to the wheel cylinder of each drive wheel to reduce slippage.

Hydraulic Circuit
X114910C02
0.833,1.635 1.146,1.792 0.313,0.156 10 false *1 6.198,1.635 6.51,1.792 0.313,0.156 10 false *2 1.49,2.01 1.802,2.167 0.313,0.156 10 false *3 1.479,2.906 1.792,3.063 0.313,0.156 10 false *4 0.688,0.042 1,0.198 0.313,0.156 10 false *a 0.75,4.469 1.063,4.625 0.313,0.156 10 false *b 2.99,4.458 3.302,4.615 0.313,0.156 10 false *c 4.385,4.458 4.698,4.615 0.313,0.156 10 false *d 6.563,4.458 6.875,4.615 0.313,0.156 10 false *e 6.344,0.052 6.656,0.208 0.313,0.156 10 false *a 2.646,2.01 2.958,2.167 0.313,0.156 10 false *3 4.438,2.01 4.75,2.167 0.313,0.156 10 false *3 5.563,2.01 5.875,2.167 0.313,0.156 10 false *3 2.646,2.906 2.958,3.063 0.313,0.156 10 false *4 4.438,2.906 4.75,3.063 0.313,0.156 10 false *4 5.583,2.906 5.896,3.063 0.313,0.156 10 false *4
*1 No. 1 Master Cylinder Cut Solenoid Valve *2 No. 2 Master Cylinder Cut Solenoid Valve
*3 Pressure Holding Solenoid Valve *4 Pressure Reduction Solenoid Valve
*a From Brake Master Cylinder Sub-assembly *b To Front Brake Caliper RH
*c To Rear Brake Caliper LH *d To Rear Brake Caliper RH
*e To Front Brake Caliper LH - -


TRC Operation
TRC Not Activated Activated
Increase Mode Holding Mode Reduction Mode
No. 1 Master Cylinder Cut Solenoid Valve OFF (Open) ON* ON* ON*
No. 2 Master Cylinder Cut Solenoid Valve OFF (Open) ON* ON* ON*
Front Wheel Pressure Holding Solenoid Valve OFF (Open) OFF (Open) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve OFF (Closed) OFF (Closed) OFF (Closed) ON (Open)
Wheel Cylinder Pressure - Increases Holds Reduces
Rear Wheel Pressure Holding Solenoid Valve OFF (Open) ON (Closed) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve OFF (Closed) OFF (Closed) OFF (Closed) OFF (Closed)
Wheel Cylinder Pressure - - - -

HINT:

*: The solenoid valve controls the brake fluid pressure by continually opening and closing the valve in accordance with the operating conditions.




d.

VSC (for Oversteer)

i.

The VSC system controls the brake fluid pressure of each wheel cylinder in order to control rear wheel skidding.


ii.

When the vehicle is oversteering while turning to the right, the VSC system controls each pressure holding solenoid valve and pressure reduction valve as shown in the illustration, in order to control rear wheel skidding.

Hydraulic Circuit
X114911C03
0.823,1.625 1.135,1.781 0.313,0.156 10 false *1 6.188,1.635 6.5,1.792 0.313,0.156 10 false *2 1.479,2.021 1.792,2.177 0.313,0.156 10 false *3 1.479,2.938 1.792,3.094 0.313,0.156 10 false *4 0.698,0.042 1.01,0.198 0.313,0.156 10 false *a 0.771,4.448 1.083,4.604 0.313,0.156 10 false *b 2.979,4.438 3.292,4.594 0.313,0.156 10 false *c 4.354,4.448 4.667,4.604 0.313,0.156 10 false *d 6.563,4.427 6.875,4.583 0.313,0.156 10 false *e 2.635,2.021 2.948,2.177 0.313,0.156 10 false *3 4.417,2.021 4.729,2.177 0.313,0.156 10 false *3 5.563,2.021 5.875,2.177 0.313,0.156 10 false *3 2.625,2.938 2.938,3.094 0.313,0.156 10 false *4 4.427,2.938 4.74,3.094 0.313,0.156 10 false *4 5.573,2.938 5.885,3.094 0.313,0.156 10 false *4 6.354,0.021 6.667,0.177 0.313,0.156 10 false *a
*1 No. 1 Master Cylinder Cut Solenoid Valve *2 No. 2 Master Cylinder Cut Solenoid Valve
*3 Pressure Holding Solenoid Valve *4 Pressure Reduction Solenoid Valve
*a From Brake Master Cylinder Sub-assembly *b To Front Brake Caliper RH
*c To Rear Brake Caliper LH *d To Rear Brake Caliper RH
*e To Front Brake Caliper LH - -


VSC Operation (for Oversteer)
VSC Not Activated Activated
Increase Mode Holding Mode Reduction Mode
No. 1 Master Cylinder Cut Solenoid Valve OFF (Open) ON* ON* ON*
No. 2 Master Cylinder Cut Solenoid Valve OFF (Open) ON* ON* ON*
Front Wheel RH Pressure Holding Solenoid Valve OFF (Open) ON (Closed) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve OFF (Closed) OFF (Closed) OFF (Closed) OFF (Closed)
Wheel Cylinder Pressure - - - -
Front Wheel LH Pressure Holding Solenoid Valve OFF (Open) OFF (Open) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve OFF (Closed) OFF (Closed) OFF (Closed) ON (Open)
Wheel Cylinder Pressure - Increases Holds Reduces
Rear Wheel RH Pressure Holding Solenoid Valve OFF (Open) ON (Closed) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve OFF (Closed) OFF (Closed) OFF (Closed) OFF (Closed)
Wheel Cylinder Pressure - - - -
Rear Wheel LH Pressure Holding Solenoid Valve OFF (Open) OFF (Open) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve OFF (Closed) OFF (Closed) OFF (Closed) ON (Open)
Wheel Cylinder Pressure - Increases Holds Reduces

HINT:

*: The solenoid valve controls the brake fluid pressure by continually opening and closing the valve in accordance with the operating conditions.




e.

VSC (for Understeer)

i.

The VSC system controls the brake fluid pressure of each wheel cylinder in order to control front wheel skidding.


ii.

When the vehicle is understeering while turning to the right, the VSC system controls each pressure holding solenoid valve and pressure reduction valve as shown in the illustration, in order to control front wheel skidding.

Hydraulic Circuit
X114912C03
0.833,1.615 1.146,1.771 0.313,0.156 10 false *1 6.188,1.615 6.5,1.771 0.313,0.156 10 false *2 1.479,2 1.792,2.156 0.313,0.156 10 false *3 1.479,2.917 1.792,3.073 0.313,0.156 10 false *4 0.698,0.042 1.01,0.198 0.313,0.156 10 false *a 0.76,4.479 1.073,4.635 0.313,0.156 10 false *b 2.99,4.458 3.302,4.615 0.313,0.156 10 false *c 4.375,4.469 4.688,4.625 0.313,0.156 10 false *d 6.573,4.438 6.885,4.594 0.313,0.156 10 false *e 6.333,0.042 6.646,0.198 0.313,0.156 10 false *a 2.635,2 2.948,2.156 0.313,0.156 10 false *3 4.417,2 4.729,2.156 0.313,0.156 10 false *3 5.573,2 5.885,2.156 0.313,0.156 10 false *3 2.646,2.917 2.958,3.073 0.313,0.156 10 false *4 4.427,2.917 4.74,3.073 0.313,0.156 10 false *4 5.573,2.917 5.885,3.073 0.313,0.156 10 false *4
*1 No. 1 Master Cylinder Cut Solenoid Valve *2 No. 2 Master Cylinder Cut Solenoid Valve
*3 Pressure Holding Solenoid Valve *4 Pressure Reduction Solenoid Valve
*a From Brake Master Cylinder Sub-assembly *b To Front Brake Caliper RH
*c To Rear Brake Caliper LH *d To Rear Brake Caliper RH
*e To Front Brake Caliper LH - -


VSC Operation (for Understeer)
VSC Not Activated Activated
Increase Mode Holding Mode Reduction Mode
No. 1 Master Cylinder Cut Solenoid Valve OFF (Open) ON* ON* ON*
No. 2 Master Cylinder Cut Solenoid Valve OFF (Open) ON* ON* ON*
Front Wheel RH Pressure Holding Solenoid Valve OFF (Open) OFF (Open) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve OFF (Closed) OFF (Closed) OFF (Closed) ON (Open)
Wheel Cylinder Pressure - Increases Holds Reduces
Front Wheel LH Pressure Holding Solenoid Valve OFF (Open) OFF (Open) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve OFF (Closed) OFF (Closed) OFF (Closed) ON (Open)
Wheel Cylinder Pressure - Increases Holds Reduces
Rear Wheel RH Pressure Holding Solenoid Valve OFF (Open) OFF (Open) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve OFF (Closed) OFF (Closed) OFF (Closed) ON (Open)
Wheel Cylinder Pressure - Increases Holds Reduces
Rear Wheel LH Pressure Holding Solenoid Valve OFF (Open) ON (Closed) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve OFF (Closed) OFF (Closed) OFF (Closed) OFF (Closed)
Wheel Cylinder Pressure - - - -

HINT:

*: The solenoid valve controls the brake fluid pressure by continually opening and closing the valve in accordance with the operating conditions.




f.

Active Cornering Assist (ACA)

i.

Active Cornering Assist (ACA), by way of solenoid valves, controls the fluid pressure generated by the pump and applies it to each wheel cylinder in the following 3 modes: pressure reduction, pressure holding, and pressure increase modes. As a result, understeer tendencies are controlled.


ii.

Understeer restraining control is performed by applying the brakes for the wheels on the inner circle of the turn. Also, depending on whether the brakes are applied and the vehicle condition, there are circumstances in which the brake of a specific wheel may not be applied even if it was targeted for braking.


iii.

The operation of the solenoid valves under the Active Cornering Assist (ACA) is the same as the operation of the VSC understeer restraining control.



g.

Hill-start Assist Control

i.

Hill-start assist control temporarily maintains the brake fluid pressure of all 4 wheels to prevent the vehicle from rolling backward.

Hydraulic Circuit (Pressure Maintained)
X114913C04
0.865,1.625 1.177,1.781 0.313,0.156 10 false *1 6.188,1.625 6.5,1.781 0.313,0.156 10 false *2 1.469,2.031 1.781,2.188 0.313,0.156 10 false *3 1.469,2.938 1.781,3.094 0.313,0.156 10 false *4 0.688,0.042 1,0.198 0.313,0.156 10 false *a 0.75,4.458 1.063,4.615 0.313,0.156 10 false *b 2.99,4.448 3.302,4.604 0.313,0.156 10 false *c 4.365,4.448 4.677,4.604 0.313,0.156 10 false *d 6.563,4.438 6.875,4.594 0.313,0.156 10 false *e 6.354,0.031 6.667,0.188 0.313,0.156 10 false *a 2.615,2.031 2.927,2.188 0.313,0.156 10 false *3 4.438,2.031 4.75,2.188 0.313,0.156 10 false *3 5.573,2.031 5.885,2.188 0.313,0.156 10 false *3 2.625,2.938 2.938,3.094 0.313,0.156 10 false *4 4.448,2.938 4.76,3.094 0.313,0.156 10 false *4 5.594,2.938 5.906,3.094 0.313,0.156 10 false *4
*1 No. 1 Master Cylinder Cut Solenoid Valve *2 No. 2 Master Cylinder Cut Solenoid Valve
*3 Pressure Holding Solenoid Valve *4 Pressure Reduction Solenoid Valve
*a From Brake Master Cylinder Sub-assembly *b To Front Brake Caliper RH
*c To Rear Brake Caliper LH *d To Rear Brake Caliper RH
*e To Front Brake Caliper LH - -


Hill-assist Control Operation
Hill-assist Control Not Activated Activated
Holding Mode Reduction Mode
No. 1 Master Cylinder Cut Solenoid Valve OFF (Open) ON (Closed) OFF (Open)
No. 2 Master Cylinder Cut Solenoid Valve OFF (Open) ON (Closed) OFF (Open)
Front Wheel Pressure Holding Solenoid Valve OFF (Open) OFF (Open) OFF (Open)
Pressure Reduction Solenoid Valve OFF (Closed) OFF (Closed) OFF (Closed)
Wheel Cylinder Pressure - Holds Reduces
Rear Wheel Pressure Holding Solenoid Valve OFF (Open) OFF (Open) OFF (Open)
Pressure Reduction Solenoid Valve OFF (Closed) OFF (Closed) OFF (Closed)
Wheel Cylinder Pressure - Holds Reduces



h.

Steering Cooperative Control Operation

i.

The operation of the solenoid valves under the steering cooperative control is the same as the TRC or VSC operation.