Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2020.03–2020.07
NM36W0E _51 Engine / Hybrid System _088520 HYBRID / BATTERY CONTROL _0421728 HYBRID CONTROL SYSTEM CO CONTROL F

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  CONTROL  THS-II CONTROL  


FUNCTION OF MAIN COMPONENTS


a.

The main components of the hybrid system have the following functions:

Component Function

*1: Models with entry and start system

*2: Models without entry and start system

Hybrid Vehicle Control ECU Performs comprehensive control of the hybrid system.
·

Information from various sensors as well as from ECUs (ECM, MG ECU, battery ECU assembly and skid control ECU) is received, and based on this the required torque and output power is calculated. The hybrid vehicle control ECU transmits the calculated result to the ECM, MG ECU and skid control ECU.

·

Monitors the SOC of the HV battery.

·

Monitors the high-voltage system for breakdown of the electrical insulation.

·

Controls the DC-DC converter.

·

Controls the inverter water pump with motor assembly.


Hybrid Vehicle Transaxle Assembly Motor Generator No. 1 (MG1) MG1, which is driven by the engine, generates high-voltage electricity in order to operate MG2 and charge the HV battery. Also, it functions as a starter to start the engine.
Motor Generator No. 2 (MG2)
·

MG2, which is driven by electrical power from MG1 and the HV battery, generates motive force for the drive wheels.

·

During braking, or when the accelerator pedal is not depressed, it generates high-voltage electricity to recharge the HV battery.


Generator Resolver (For MG1) Detects the rotor position, rotational speed and direction of MG1.
Motor Resolver (For MG2) Detects the rotor position, rotational speed and direction of MG2.
Generator Temperature Sensor (For MG1) Detects the temperature of MG1.
Motor Temperature Sensor (For MG2) Detects the temperature of MG2.
ATF Temperature Sensor Detects the temperature of ATF.
Power Split Planetary Gear Unit Distributes the engine motive force as appropriate to drive the vehicle as well as MG1.
Motor Speed Reduction Gear Unit Reduces the rotational speed of MG2 in accordance with the characteristics of the reduction gear, in order to increase torque.
Inverter with Converter Assembly Inverter Converts the direct current from the boost converter into alternating current for MG1 and MG2, and vice versa (from AC to DC).
Boost Converter Boosts the HV battery nominal voltage of DC 177.6 V up to a maximum voltage of DC 580 V and vice versa (steps down DC 580 V to DC 177.6 V).
DC-DC Converter Steps down the HV battery nominal voltage of DC 177.6 V to approximately DC 14 V in order to supply electricity to the electrical components, as well as to recharge the auxiliary battery.
MG ECU Controls the inverter and boost converter in accordance with the signals received from the hybrid vehicle control ECU, thus operating MG1 and MG2 as either a generator or motor.
Temperature Sensor for Inverter with Converter Assembly Detects temperatures in the parts of the inverter with converter assembly as well as the HV coolant temperature.
Inverter Current Sensor Detects the current of MG1 and MG2.
HV Battery HV Battery (Battery Modules)
·

Supplies electrical power to MG1 and MG2 in accordance with the driving conditions of the vehicle.

·

Recharged by MG1 and MG2 in accordance with the SOC and the driving conditions of the vehicle.


Service Plug Grip Shuts off the high-voltage circuit of the HV battery when the service plug grip is removed for vehicle inspection or maintenance.
Battery ECU Assembly
·

Monitors the conditions of the HV battery such as voltage, current and temperature, and calculates the SOC of the HV battery based on the charge/discharge amperage detected by the battery current sensor.

·

Transmits this information to the hybrid vehicle control ECU.

·

Controls the battery cooling blower assembly.


HV Battery Temperature Sensor Detects temperatures in the parts of the HV battery.
HV Battery Intake Air Temperature Sensor Detects the intake air temperature from the battery cooling blower assembly.
No. 1 Traction Battery Device Box Assembly System Main Relays Connects and disconnects the high-voltage circuit between the HV battery and the inverter with converter assembly through the use of signals from the hybrid vehicle control ECU.
Battery Current Sensor Detects the input and output current of the HV battery.
Battery Cooling Blower Assembly Operates under the control of the battery ECU assembly in order to cool the HV battery.
Interlock Switch
·

Service Plug Grip

·

Inverter Cover Sub-assembly Upper


Verifies that the service plug grip and inverter cover sub-assembly upper are installed.
Inverter Water Pump with Motor Assembly Operates under the control of the hybrid vehicle control ECU in order to cool the inverter with converter assembly, MG1 and MG2.
Compressor with Motor Assembly Is driven by the hybrid vehicle control ECU using power from the HV battery to intake, compress and discharge refrigerant at a speed calculated by the air conditioning amplifier assembly, in order to provide constant air conditioning operation regardless of the engine operation state.
Power Cable Connects the HV battery, inverter with converter assembly, hybrid vehicle transaxle assembly and compressor with motor assembly.
Shift Lever Position Sensor Converts the shift position into electrical signals and sends them to the hybrid vehicle control ECU.
Accelerator Pedal Sensor Assembly Converts the accelerator pedal position into an electrical signal and sends it to the hybrid vehicle control ECU.
Stop Light Switch Assembly Detects the depression of the brake pedal.
Combination Switch Assembly EV Drive Mode Switch Sends the EV drive mode switch signal to the hybrid vehicle control ECU when operated by the driver.
Drive Mode Select Switch Sends the power mode, ECO mode or normal mode signal to the hybrid vehicle control ECU when operated by the driver.
Auxiliary Battery Supplies electricity to the electrical components.
Battery State Sensor Assembly Calculates the current, voltage, temperature, SOC (battery charging percentage), SHC (battery degradation percentage) and SOF (starting performance) of the auxiliary battery.
ECM
·

Performs control of the engine in accordance with the target engine speed and required engine motive force received from the hybrid vehicle control ECU.

·

Transmits various engine operating condition signals to the hybrid vehicle control ECU.


Brake Booster with Master Cylinder Assembly Skid Control ECU
·

During braking, it calculates the required regenerative braking force and transmits it to the hybrid vehicle control ECU.

·

Transmits the request to the hybrid vehicle control ECU to limit motive force while the TRC or VSC is operating.


Air Conditioning Amplifier Assembly Transmits various A/C state signals to the hybrid vehicle control ECU.
Airbag ECU Assembly During a collision, it transmits the airbag deployment signal to the hybrid vehicle control ECU.
Certification ECU (Smart Key ECU Assembly)*1 Sends the starter signal to the hybrid vehicle control ECU.
Ignition or Starter Switch Assembly*2
Combination Meter Assembly READY Indicator Informs the driver that the vehicle is ready to drive.
Malfunction Indicator Lamp (MIL) Turns on when there is a malfunction in the hybrid control system or engine control system.
Shift Position Indicator Displays shift position.
EV Drive Mode Indicator Displays EV Drive mode.
Power Mode Indicator Displays Power mode.
Eco Drive Mode Indicator Displays Eco Drive mode.
EV Driving Indicator Informs the driver that the EV drive is entered.
Multi-information Display
·

Displays energy monitor.

·

Displays a warning message to inform or warn the driver of the system condition in accordance with signals from the hybrid vehicle control ECU.





SYSTEM CONTROL


a.

Control List

i.

The hybrid system consists of the controls listed below.

Control Outline
Hybrid Vehicle Control
·

The hybrid vehicle control ECU calculates the target motive force based on the shift lever position sensor, accelerator pedal opening angle and vehicle speed. It performs control in order to create the target motive force by optimally combining MG1, MG2 and the engine.

·

The hybrid vehicle control ECU calculates the engine motive force based on the target motive force, which has been calculated based on the requirements of the driver and the driving conditions of the vehicle. In order to create this motive force, the hybrid vehicle control ECU transmits the signals to the ECM.

·

The hybrid vehicle control ECU monitors the SOC of the HV battery and the temperature of the HV battery, MG1 and MG2, in order to optimally control these items.


SOC Control
·

The battery ECU assembly calculates the SOC by estimating the charging and discharging amperage of the HV battery.

·

The battery ECU assembly transmits this information to the hybrid vehicle control ECU.

·

The hybrid vehicle control ECU constantly performs charge/discharge control based on the calculated SOC in order to maintain the SOC within its target range.


Engine Control The ECM receives the target engine speed and required engine motive force, which were sent from the hybrid vehicle control ECU, and controls the ETCS-i, fuel injection volume, ignition timing, VVT-i and EGR.
Motor Generator Main Control
·

MG1, which is driven by the engine, generates high-voltage electricity in order to operate MG2 and charge the HV battery. Also, it functions as a starter to start the engine.

·

MG2, which is driven by electrical power from MG1 and/or the HV battery, generates motive force for the front wheels.

·

MG2 generates high-voltage electricity to charge the HV battery during braking (regenerative braking cooperative control), or when the accelerator pedal is not being depressed (energy regeneration).

·

MG1 and MG2 are basically shut down when neutral (N) is selected. In order to stop providing motive force, it is necessary to stop driving MG1 and MG2, because MG1 and MG2 are mechanically joined to the drive wheels.


Inverter Control
·

The inverter converts the direct current from the HV battery into alternating current for MG1 and MG2, or vice versa, in accordance with the signals provided by the hybrid vehicle control ECU via the MG ECU. In addition, the inverter is used to transfer electrical power generated by the MG1 to MG2.

·

The hybrid vehicle control ECU shuts down the inverter if it receives an overheating, overcurrent or voltage fault signal from the inverter via the MG ECU.


Boost Converter Control
·

The boost converter boosts the HV battery nominal voltage of DC 177.6 V up to a maximum voltage of DC 580 V, in accordance with the signals provided by the hybrid vehicle control ECU via the MG ECU.

·

The inverter converts the alternating current generated by MG1 or MG2 into the direct current. The boost converter steps down the generated voltage of DC 580 V (maximum voltage) to approximately DC 177.6 V, in accordance with the signals provided by the hybrid vehicle control ECU via the MG ECU.


DC-DC Converter Control The DC-DC converter steps down the HV battery nominal voltage of DC 177.6 V to approximately DC 14 V in order to supply electricity to the electrical components, as well as to recharge the auxiliary battery.
System Main Relay Control To ensure that it is possible to connect and disconnect the high-voltage circuits reliably, the hybrid vehicle control ECU controls the 3 system main relays to connect and disconnect the high-voltage circuits from the HV battery. The hybrid vehicle control ECU also uses the timing of the operation of the 3 system main relays to monitor the operation of the relay contacts.
Cooling System Control for Inverter with Converter Assembly In order to cool the inverter with converter assembly, MG1 and MG2, the hybrid vehicle control ECU regulates the inverter water pump with motor assembly according to the signals from the temperature sensor for inverter with converter assembly, temperature sensor for MG1 and temperature sensor for MG2.
Cooling System Control for HV Battery In order to maintain the HV battery temperature at the optimum level, the battery ECU assembly regulates the battery cooling blower assembly according to the signals from the HV battery temperature sensors and HV battery intake air temperature sensor.
Regenerative Braking Cooperative Control During braking, the skid control ECU calculates the required regenerative braking force and transmits it to the hybrid vehicle control ECU. Upon receiving this signal, the hybrid vehicle control ECU transmits the actual regenerative braking control value to the skid control ECU. Based on this result, the skid control ECU calculates and executes the required hydraulic braking force.
TRC/VSC Cooperative Control The skid control ECU transmits the request to the hybrid vehicle control ECU to limit motive force while the TRC or VSC is operating. The hybrid vehicle control ECU controls the engine and MG2 in accordance with the present driving conditions in order to suppress the motive force. (For details, refer to Brake Control System.)
During Collision Control During a collision, if the hybrid vehicle control ECU receives the airbag deployment signal from the airbag ECU assembly, it turns the system main relays off in order to shut off the high-voltage from the HV battery.
Dynamic Radar Cruise Control Upon receiving a motive force request signal from the forward recognition camera, the hybrid vehicle control ECU optimizes the motive forces of the engine, MG2 in order to obtain the target vehicle speed. (For details, refer to Dynamic Radar Cruise Control System.)
Shift Control The hybrid vehicle control ECU detects the driver's desired shift state (P, R, N, D or B) in accordance with the signals provided by the shift lever position sensor. Based on these inputs and vehicle operating conditions, the hybrid vehicle control ECU controls MG1, MG2 and the engine to match the selected shift state.
EV Drive Mode Control When the EV drive mode switch is operated by the driver, the hybrid vehicle control ECU uses only MG2 to drive the vehicle if the operating conditions are satisfied.
Power Mode Control When the drive mode select switch (combination switch assembly) is operated by the driver, the hybrid vehicle control ECU modulates the response of the accelerator pedal operation to optimize acceleration.
ECO Mode Control When the drive mode select switch (combination switch assembly) is operated by the driver, the hybrid vehicle control ECU modulates the response of the accelerator pedal operation to support Eco driving.
Brake Override System The hybrid system output is restricted when both the accelerator and brake pedals are depressed. (For the Activation Conditions and Inspection Method, refer to the Repair Manual)
Engine Immobiliser Control Prohibits fuel delivery, ignition and starting the hybrid control system if an attempt is made to start the hybrid control system with an invalid key.
Drive Start Control If an abnormal shift (R to D/B, D/B to R, N to R, P to D/B, P to R) is detected while accelerating, a warning is displayed in the multi-information display and hybrid system output is reduced to limit the acceleration helping to avoid a collision.



b.

Hybrid System Activation (READY-on State)

i.

The hybrid system can be activated by pressing the power switch (push start switch) while the brake pedal is being depressed*1 or turning the ignition switch further from the ON position*2. At this time, the READY indicator light flashes until the system check is completed. When the READY indicator light turns on, the hybrid system has started and the vehicle is ready to drive.

*1: Models with entry and start system

*2: Models without entry and start system



ii.

Even if the driver turns the ignition switch on (READY), sometimes the hybrid vehicle control ECU will not start the engine. The engine will only start if conditions such as engine coolant temperature, SOC, HV battery temperature and electrical load require an engine start.


iii.

After driving, when the driver stops the vehicle and moves the shift lever to P, the hybrid vehicle control ECU allows the engine to continue running. The engine will stop after the SOC, HV battery temperature and electrical load reach a specified level.

NOTICE:
·

For models with entry and start system, when the hybrid system is unavoidably required to be stopped while driving, the system can be forced to stop by pressing and holding the power switch (push start switch) for approximately 2 seconds or more or pushing the power switch (push start switch) 3 times or more in a row. At this time, the power source will change to on (IG ON).

·

For models without entry and start system, when the hybrid system is unavoidably required to be stopped while driving, the system can be forced to stop by turning the ignition switch to ACC.





c.

EV Drive Mode Control

i.

Depending on the condition of the hybrid control system and the driving conditions, the driving mode may not be able to be changed to EV mode and a warning message will be displayed on the multi-information display.

HINT:

Under the following conditions, the driving mode will not be able to be changed to EV mode:

·

The hybrid control system is extremely hot.

-

After the vehicle has been parked in an extremely hot environment, driven at high speeds or the vehicle is climbing a slope, etc.


·

The hybrid control system is extremely cold.

-

After the vehicle has been parked in an extremely cold environment (approximately 0°C (32°F) or less) for a long period of time.


·

The engine is warming up.

·

The SOC (State of Charge) of the HV battery is low.

·

The vehicle is being driven at a speed higher than the specified value.

-

The vehicle speed is approximately 45 km/h (28 mph) or higher.


·

The accelerator pedal is being fully depressed or the vehicle is climbing a slope.

·

The defroster is on.

·

The HV battery temperature is high.

·

The HV battery temperature is low.

·

The engine is operated to warm the catalyst.

·

DTCs are stored.




ii.

EV drive mode has been provided to reduce vehicle noise, such as when entering or leaving a garage, as well as reducing the production of exhaust fumes in a garage. When the EV drive mode switch is operated by the driver, the hybrid vehicle control ECU uses only MG2 to drive the vehicle if the operating conditions are satisfied.


iii.

When all operating conditions are satisfied, pressing the EV drive mode switch causes the vehicle to enter EV drive mode, and the EV drive mode indicator will be illuminated. If any operating condition is not satisfied and the EV drive mode switch is pressed, the EV drive mode indicator flashes 3 times and a buzzer sounds to inform the driver that the EV drive mode switch operation was rejected, and EV drive mode cannot be entered.


iv.

If the operating conditions are no longer met while the vehicle is traveling in EV drive mode, in order to inform the driver that EV drive mode will be canceled, the EV drive mode indicator flashes 3 times and a buzzer sounds.



d.

Power Mode and ECO Mode

i.

During power mode, the hybrid vehicle control ECU optimizes acceleration feel by increasing the power output more quickly at the beginning of accelerator pedal operation.


ii.

During ECO mode, the hybrid vehicle control ECU optimizes fuel economy and driving performance by gently generating the driving force in comparison to accelerator pedal operation. At the same time, it supports Eco driving by optimizing the air conditioning performance.

W136988E09
4.167,0.917 4.333,1.333 4.333,1.333 4.5,1.333 true 3.333,1.25 3.667,1.917 3.667,1.917 3.833,1.917 true 3.542,0.823 3.698,0.188 3.698,0.188 3.865,0.188 true 2.083,1.333 2.75,1.333 true 1.219,0.375 2.458,0.646 1.24,0.271 10 false Rate of acceleration 3.042,2.323 4.917,2.552 1.875,0.229 10 false Accelerator opening angle 3.927,0.083 4.792,0.51 0.865,0.427 10 false Power Mode 4.542,1.25 6.875,1.5 2.333,0.25 10 false Eco Mode 3.875,1.833 6.51,2.083 2.635,0.25 10 false Normal Mode 0.354,1.24 2.031,1.615 1.677,0.375 10 false High impression of powerful acceleration



e.

Hybrid Vehicle Control

i.

The hybrid vehicle control ECU detects the degree to which the accelerator pedal is depressed using the signals from the accelerator pedal sensor assembly and detects the shift position signals from the shift lever position sensor. The hybrid vehicle control ECU receives the speed signals from the MG1 and MG2 resolvers via the MG ECU. The hybrid vehicle control ECU determines the driving conditions of the vehicle in accordance with this information, and optimally controls the motive forces of MG1, MG2 and the engine. Furthermore, the hybrid vehicle control ECU optimally controls the output and torque of MG1, MG2 and the engine in order to deliver lower fuel consumption and cleaner exhaust emissions.


ii.

The hybrid vehicle control ECU calculates the engine motive force based on the calculated target motive force, and by taking the SOC and the temperature of the HV battery into consideration. The value obtained by subtracting the engine motive force from the target motive force is the MG2 motive force.


iii.

The ECM performs control of the engine in accordance with the target engine speed and required engine motive force received from the hybrid vehicle control ECU. Furthermore, the hybrid vehicle control ECU appropriately operates MG1 and MG2 in order to provide the required MG1 generation force and the required MG2 motive force.

Flow of Motive Force Calculation
W137563E08
0.542,0.281 5.531,0.542 4.99,0.26 10 false (Target Motive Force) - (Engine Motive Force) = (MG2 Motive Force) 0.25,0.969 1.688,1.188 1.438,0.219 10 false Battery ECU Assembly 2.24,0.927 4.958,1.208 2.719,0.281 10 false Hybrid Vehicle Control ECU 0.396,1.833 1.563,2.125 1.167,0.292 10 false Battery Condition 0.344,2.198 1.51,2.49 1.167,0.292 10 false - Voltage 0.333,2.479 1.5,2.771 1.167,0.292 10 false - Current 0.344,2.781 1.51,3.073 1.167,0.292 10 false - Temperature 0.531,3.302 1.25,3.667 0.719,0.365 10 false SOC Calculation 3.354,1.573 4.5,1.927 1.146,0.354 10 false Total Motive Force Calculation 5.969,0.948 6.625,1.198 0.656,0.25 10 false ECM 5.75,1.385 6.729,1.646 0.979,0.26 10 false ETCS-i Control 5.448,1.865 6.792,2.229 1.344,0.365 10 false Fuel Injection Volume Control 5.469,2.656 6.885,3 1.417,0.344 10 false Ignition Timing Control 5.719,3.104 6.698,3.344 0.979,0.24 10 false VVT-i Control 5.594,4.573 6.771,4.833 1.177,0.26 10 false Skid Control ECU 5.708,5.052 6.885,5.313 1.177,0.26 10 false Brake Control 3.594,4.625 4.344,5.167 0.75,0.542 10 false Drive Power Distribution Calculation 2.198,4.208 2.938,4.896 0.74,0.688 10 false Target Motive Force Calculation 0.292,4.552 1.417,4.906 1.125,0.354 10 false Accelerator Pedal Sensor Assembly 0.208,5.677 1.427,6.031 1.219,0.354 10 false Shift Lever Position Sensor 1.51,6.885 2.792,7.271 1.281,0.385 10 false Rotation Sensors for MG1, MG2 4.875,6.063 5.479,6.385 0.604,0.323 10 false MG ECU 4.635,6.938 5.74,7.302 1.104,0.365 10 false MG1 Generation Force Calculation 4.635,7.781 5.792,8.146 1.156,0.365 10 false MG2 Motive Force Calculation



f.

SOC Control

i.

The battery ECU assembly calculates the SOC of the HV battery based on the charge/discharge amperage detected by the battery current sensor. The battery ECU assembly transmits this information to the hybrid vehicle control ECU. The hybrid vehicle control ECU constantly performs charge/discharge control based on the calculated SOC in order to maintain the SOC within its target range.


ii.

While the vehicle is in motion, the HV battery undergoes repetitive charge/discharge cycles, as it becomes discharged by MG2 during acceleration and charged by regenerative braking during deceleration.


iii.

When the SOC is below the lower level, the hybrid vehicle control ECU increases the power output of the engine to operate MG1, which charges the HV battery.


iv.

The battery ECU assembly converts the HV battery related signals (SOC, voltage, current and temperature) into digital signals, and transmits them to the hybrid vehicle control ECU via CAN communication.

W131738E02
0.438,0.313 2.01,0.646 1.573,0.333 10 false Battery Current Sensor 0.781,1.292 1.5,1.49 0.719,0.198 10 false HV Battery 0.385,1.656 1.958,1.99 1.573,0.333 10 false - HV Battery Voltage 0.677,2.302 1.469,2.833 0.792,0.531 10 false HV Battery Temperature Sensor 2.958,1.531 3.771,1.906 0.813,0.375 10 false Battery ECU Assembly 5.813,1.208 6.74,1.75 0.927,0.542 10 false Hybrid Vehicle Control ECU 4.167,2.042 5.49,2.417 1.323,0.375 10 false CAN Communication Line



g.

Engine Control

i.

The ECM receives the target engine speed and required engine motive force, which were sent from the hybrid vehicle control ECU, and controls the ETCS-i, fuel injection volume, ignition timing, VVT-i and EGR.


ii.

The ECM transmits the operating conditions of the engine to the hybrid vehicle control ECU.


iii.

Upon receiving the engine stop signal from the hybrid vehicle control ECU in accordance with the basic hybrid vehicle control, the ECM will stop the engine.

W122958E20
5.792,0.271 6.813,0.49 1.021,0.219 10 false ETCS-i Control 5.802,0.74 6.833,1.115 1.031,0.375 10 false Fuel Injection Volume Control 5.833,1.531 6.865,1.906 1.031,0.375 10 false Ignition Timing Control 5.844,2.323 6.792,2.552 0.948,0.229 10 false VVT-i Control 5.698,2.823 6.917,3.208 1.219,0.385 10 false Combination Meter Assembly 6.167,3.688 6.615,3.885 0.448,0.198 10 false MIL 4.438,2.083 4.885,2.281 0.448,0.198 10 false ECM 2.135,1.917 3.094,2.281 0.958,0.365 10 false Hybrid Vehicle Control ECU 3.135,2.271 4.104,2.792 0.969,0.521 10 false CAN Communication Line 3.76,1.646 3.99,1.813 0.229,0.167 10 false *2 3.313,1.646 3.542,1.813 0.229,0.167 10 false *1 0.385,0.271 1.594,0.688 1.208,0.417 10 false Accelerator Pedal Sensor Assembly 0.365,1.229 1.573,1.646 1.208,0.417 10 false Shift Lever Position Sensor 0.375,2.208 1.417,2.604 1.042,0.396 10 false MG ECU 0.26,3.406 1.594,3.781 1.333,0.375 10 false Rotation Sensors for MG1, MG2 1.698,4.417 3.833,4.656 2.135,0.24 10 false *1: Engine operating conditions 3.854,4.417 5.99,4.656 2.135,0.24 10 false *2: Engine control requests



h.

Motor Generator Main Control

i.

MG1, which is driven by the engine, generates high-voltage electricity in order to operate MG2 and charge the HV battery. Also, it functions as a starter to start the engine.


ii.

MG2, which is driven by electrical power from MG1 and the HV battery, generates motive force for the front wheels.


iii.

MG2 generates high-voltage electricity to charge the HV battery during braking (regenerative braking cooperative control), or when the accelerator pedal is not being depressed (energy regeneration).


iv.

MG1 and MG2 are basically shut down when neutral (N) is selected. In order to stop providing motive force, it is necessary to stop driving MG1 and MG2, because MG1 and MG2 are mechanically joined to the drive wheels.


v.

The MG ECU controls the Insulated Gate Bipolar Transistors (IGBTs) in the Intelligent Power Module (IPM) based on the signals received from the hybrid vehicle control ECU. The IGBTs are used for switching for the U, V, and W phases of each motor generator. There are 6 IGBTs that switch on and off to control each individual motor generator in accordance with operation as either a motor or as a generator.


vi.

The illustration below describes the basic control used when the motor generator functions as a motor. The IGBTs in the IPM switch on and off to supply 3-phase alternating current to the motor generator. In order to create the motive force required of the motor generator as calculated by the hybrid vehicle control ECU, the MG ECU switches the IGBTs on and off in order to control the speed of the motor generator.

W145434E01
1.073,5.229 2.177,5.427 1.104,0.198 10 false Motor Generator 1.052,0.427 2.156,0.625 1.104,0.198 10 false Motor Generator 2.24,0.219 2.573,0.417 0.333,0.198 10 false U 1.969,0.688 2.302,0.885 0.333,0.198 10 false V 2.656,0.667 2.99,0.865 0.333,0.198 10 false W 3.26,2.333 3.927,2.531 0.667,0.198 10 false IPM 4.958,1.219 5.292,1.417 0.333,0.198 10 false U 4.948,3.677 5.281,3.875 0.333,0.198 10 false U 4.948,6.083 5.281,6.281 0.333,0.198 10 false U 5.438,1.219 5.771,1.417 0.333,0.198 10 false V 5.906,1.219 6.24,1.417 0.333,0.198 10 false W 5.427,3.656 5.76,3.854 0.333,0.198 10 false V 5.438,6.073 5.771,6.271 0.333,0.198 10 false V 5.927,3.646 6.26,3.844 0.333,0.198 10 false W 5.917,6.073 6.25,6.271 0.333,0.198 10 false W 4.51,0.969 4.844,1.167 0.333,0.198 10 false (+) 4.542,2.333 4.875,2.531 0.333,0.198 10 false (-) 4.51,5.844 4.844,6.042 0.333,0.198 10 false (+) 4.542,4.74 4.875,4.938 0.333,0.198 10 false (-) 4.542,7.167 4.875,7.365 0.333,0.198 10 false (-) 4.51,3.417 4.844,3.615 0.333,0.198 10 false (+) 1.052,2.854 2.156,3.052 1.104,0.198 10 false Motor Generator 3.26,4.719 3.927,4.917 0.667,0.198 10 false IPM 3.26,7.125 3.927,7.323 0.667,0.198 10 false IPM 2.208,2.625 2.542,2.823 0.333,0.198 10 false U 2.208,5.031 2.542,5.229 0.333,0.198 10 false U 1.979,3.094 2.313,3.292 0.333,0.198 10 false V 1.969,5.479 2.302,5.677 0.333,0.198 10 false V 2.635,3.094 2.969,3.292 0.333,0.198 10 false W 2.646,5.5 2.979,5.698 0.333,0.198 10 false W 0.615,7.458 1.719,7.656 1.104,0.198 10 false IGBT: ON


vii.

The illustration below describes the basic control used when the motor generator functions as a generator. The current that is generated sequentially by the 3-phases of the motor generator, which is driven by the wheels, is utilized to charge the HV battery or drive another motor generator.

W145435E01
4.938,6.094 5.094,6.292 0.156,0.198 10 false U 4.948,3.677 5.104,3.875 0.156,0.198 10 false U 4.938,1.24 5.094,1.438 0.156,0.198 10 false U 5.438,1.24 5.594,1.438 0.156,0.198 10 false V 5.438,3.667 5.594,3.865 0.156,0.198 10 false V 5.438,6.094 5.594,6.292 0.156,0.198 10 false V 5.917,6.104 6.135,6.302 0.219,0.198 10 false W 5.906,3.667 6.125,3.865 0.219,0.198 10 false W 5.906,1.24 6.125,1.438 0.219,0.198 10 false W 4.542,7.167 4.76,7.365 0.219,0.198 10 false (-) 4.542,4.74 4.76,4.938 0.219,0.198 10 false (-) 4.542,2.313 4.76,2.51 0.219,0.198 10 false (-) 4.51,5.844 4.802,6.042 0.292,0.198 10 false (+) 4.51,3.417 4.802,3.615 0.292,0.198 10 false (+) 4.51,0.99 4.802,1.188 0.292,0.198 10 false (+) 2.229,0.208 2.385,0.406 0.156,0.198 10 false U 2.229,2.604 2.385,2.802 0.156,0.198 10 false U 2.219,5.01 2.375,5.208 0.156,0.198 10 false U 1.948,0.698 2.104,0.896 0.156,0.198 10 false V 1.958,3.073 2.115,3.271 0.156,0.198 10 false V 1.948,5.458 2.104,5.656 0.156,0.198 10 false V 2.656,0.688 2.875,0.885 0.219,0.198 10 false W 2.646,3.094 2.865,3.292 0.219,0.198 10 false W 2.646,5.49 2.865,5.688 0.219,0.198 10 false W 1.073,0.438 2.198,0.677 1.125,0.24 10 false Motor Generator 1.083,2.823 2.208,3.063 1.125,0.24 10 false Motor Generator 1.083,5.229 2.208,5.469 1.125,0.24 10 false Motor Generator 3.25,7.083 3.635,7.292 0.385,0.208 10 false IPM 3.26,4.688 3.646,4.896 0.385,0.208 10 false IPM 3.25,2.302 3.635,2.51 0.385,0.208 10 false IPM



i.

Inverter Control

i.

The inverter converts the direct current from the HV battery into alternating current for MG1 and MG2, or vice versa. In addition, the inverter takes power generated by MG1 and supplies it to MG2. However, the electricity generated by MG1 is converted into direct current inside the inverter before being converted back into the alternating current by the inverter for use by MG2. This is necessary because the frequency of the alternating current output by MG1 is not appropriate for control of MG2.


ii.

The MG ECU controls the IPMs for switching the three-phase alternating current of MG1 and MG2 in accordance with the signals received from the hybrid vehicle control ECU.


iii.

When the hybrid vehicle control ECU has received an overheating, overcurrent, or voltage fault signal from the MG ECU, the hybrid vehicle control ECU transmits a shut down control signal to the MG ECU, in order to turn off the IPMs.

W130197E17
0.229,1.073 1.583,1.333 1.354,0.26 10 false Alternating Current 0.479,2.823 1.5,3.083 1.021,0.26 10 false Direct Current 0.167,3.146 1.5,3.49 1.333,0.344 10 false Maximum Voltage of DC 580 V 0.271,4 1.448,4.542 1.177,0.542 10 false Nominal Voltage of DC 177.6 V 2.563,0.573 3,0.833 0.438,0.26 10 false MG1 3.917,0.563 4.354,0.823 0.438,0.26 10 false MG2 3.146,1.063 3.833,1.479 0.688,0.417 10 false Alternating Current 5.219,1.896 6.594,2.323 1.375,0.427 10 false Inverter with Converter Assembly 2.26,2.417 3.177,2.667 0.917,0.25 10 false IPM for MG1 3.625,2.417 4.542,2.667 0.917,0.25 10 false IPM for MG2 3.25,3 4.167,3.25 0.917,0.25 10 false Inverter 2.146,3.531 3.229,3.781 1.083,0.25 10 false Boost Converter 4.188,3.552 4.854,3.802 0.667,0.25 10 false MG ECU 2.26,4.646 3.177,4.896 0.917,0.25 10 false HV Battery 4.135,4.635 5.875,4.938 1.74,0.302 10 false Hybrid Vehicle Control ECU 4.677,4.125 6.417,4.427 1.74,0.302 10 false CAN Communication Line



j.

Boost Converter Control

i.

The boost converter boosts the HV battery nominal voltage of DC 177.6 V up to a maximum voltage of DC 580 V, in accordance with the signals provided by the hybrid vehicle control ECU via the MG ECU.


ii.

The inverter converts the alternating current generated by MG1 or MG2 into direct current. The boost converter steps down the generated voltage of DC 580 V (maximum voltage) to approximately DC 177.6 V, in accordance with the signals provided by the hybrid vehicle control ECU via the MG ECU.


iii.

The boost converter consists of the boost IPM with built-in IGBTs that perform switching control, the reactor that stores the electrical power and generates the electromotive force, and the capacitor that charges and discharges the boosted high-voltage electricity.

W136959E01
5.146,0.458 4.979,0.458 4.979,0.458 4.646,1.792 true 2.583,0.583 2.75,0.583 2.75,0.583 3,1.25 true 2.583,3.333 2.75,3.333 2.75,3.333 3,2.667 true 0.344,2.292 1.104,2.51 0.76,0.219 10 false HV Battery 2.021,2.177 2.781,2.396 0.76,0.219 10 false Reactor 3.104,3.042 4.021,3.26 0.917,0.219 10 false Boost IPM 1.083,3.25 2.771,3.521 1.688,0.271 10 false IGBT2 for Voltage Boost 5.917,3.042 6.833,3.26 0.917,0.219 10 false Inverter 5.188,0.385 6.104,0.604 0.917,0.219 10 false Capacitor 1.094,0.5 2.75,0.719 1.656,0.219 10 false IGBT1 for Voltage Drop


iv.

The flow of the boost converter boosting is as described below.

Step Outline
1 IGBT2 turns on, causing the voltage of the HV battery (nominal voltage of DC 177.6 V) to charge the reactor. As a result, the reactor stores the electrical power.
2 IGBT2 turns off, causing the reactor to produce an electromotive force (the current continues to flow from the reactor). This electromotive force causes the voltage to rise to a maximum voltage of DC 580 V. Induced by the electromotive force that is created by the reactor, the current that is flowing from the reactor flows into the inverter and the capacitor at the boosted voltage.
3 IGBT2 turns on again to cause the voltage of the HV battery to charge the reactor. While this happens, by discharging the electrical power (maximum voltage of DC 580 V) stored in the capacitor, electrical power continues to be supplied to the inverter.

W136960E06
1.813,1.135 1.979,1.135 1.979,1.135 2.146,1.385 true 1.813,4.385 1.979,4.385 1.979,4.385 2.146,4.635 true 1.823,7.635 1.99,7.635 1.99,7.635 2.156,7.885 true 5.052,9.25 4.885,9.25 4.885,9.25 4.719,8.167 true 5.052,6.01 4.885,6.01 4.885,6.01 4.719,4.927 true 5.052,2.771 4.885,2.771 4.885,2.771 4.719,1.688 true 2.75,0.333 2.917,0.333 2.917,0.333 3.083,0.833 true 2.75,3.583 2.917,3.583 2.917,3.583 3.083,4.083 true 4.75,6.438 4.917,6.438 4.917,6.438 5.083,7.188 true 2.667,9.167 2.833,9.167 2.833,9.167 3,8.667 true 2.667,5.917 2.833,5.917 2.833,5.917 3,5.417 true 2.667,2.667 2.833,2.667 2.833,2.667 3,2.167 true 4.667,3.167 4.5,3.167 4.5,3.167 4.333,3.948 true 2.75,6.833 2.917,6.833 2.917,6.833 3.083,7.333 true 2.583,8.667 2.833,8.667 true 0.083,6.594 1.375,6.833 1.292,0.24 12 false Step 3: 0.083,3.333 1.375,3.573 1.292,0.24 12 false Step 2: 0.083,0.083 1.375,0.323 1.292,0.24 12 false Step 1: 1.323,7.542 1.958,7.719 0.635,0.177 10 false Reactor 1.313,4.292 1.948,4.469 0.635,0.177 10 false Reactor 1.313,1.042 1.948,1.219 0.635,0.177 10 false Reactor 3.125,2.604 4.5,2.802 1.375,0.198 10 false Boost IPM 3.125,5.854 4.5,6.052 1.375,0.198 10 false Boost IPM 3.125,9.083 4.5,9.281 1.375,0.198 10 false Boost IPM 5.917,5.854 6.448,6.042 0.531,0.188 10 false Inverter 5.917,9.083 6.448,9.271 0.531,0.188 10 false Inverter 5.917,2.604 6.448,2.792 0.531,0.188 10 false Inverter 5.083,2.698 5.802,2.854 0.719,0.156 10 false Capacitor 5.083,5.927 5.802,6.083 0.719,0.156 10 false Capacitor 5.083,9.167 5.802,9.323 0.719,0.156 10 false Capacitor 1.979,3.5 2.74,3.698 0.76,0.198 10 false IGBT1: OFF 1.979,0.25 2.74,0.469 0.76,0.219 10 false IGBT1: OFF 1.979,6.75 2.75,6.948 0.771,0.198 10 false IGBT1: OFF 1.719,2.5 3.25,2.698 1.531,0.198 10 false IGBT2: ON 1.969,9.083 2.667,9.281 0.698,0.198 10 false IGBT2: ON 1.917,5.833 3.448,6.031 1.531,0.198 10 false IGBT2: OFF 2.854,6.354 4.833,6.604 1.979,0.25 10 false Maximum Voltage of DC 580 V 4.708,3.083 6.688,3.333 1.979,0.25 10 false Maximum Voltage of DC 580 V 0.052,4.583 1.167,5.656 1.115,1.073 10 false HV Battery: Nominal Voltage of DC 177.6 V 0.052,7.844 1.167,8.917 1.115,1.073 10 false HV Battery: Nominal Voltage of DC 177.6 V 0.052,1.344 1.167,2.417 1.115,1.073 10 false HV Battery: Nominal Voltage of DC 177.6 V


v.

The alternating current which is generated by MG1 or MG2 for the purpose of charging the HV battery is converted into direct current (maximum voltage of DC 580 V) by the inverter. Then, the boost converter is used to step down the voltage to approximately DC 177.6 V. This is accomplished by IGBT1 being switched on and off using duty cycle control, intermittently interrupting the electrical power provided to the reactor by the inverter.

W136961E07
2.583,3.167 2.75,3.167 2.75,3.167 3.083,2.667 true 4.969,3.198 4.802,3.198 4.802,3.198 4.635,2.115 true 4.583,0.365 4.417,0.365 4.417,0.365 4.25,1.031 true 1.417,1 1.583,1 1.583,1 1.833,1.885 true 2.833,0.167 3,0.167 3,0.167 3.25,1.083 true 0.698,0.063 2.813,0.656 2.115,0.594 10 false IGBT1: ON/OFF Switching Control (Duty Cycle Control) 4.615,0.281 6.667,0.49 2.052,0.208 10 false Maximum Voltage of DC 580 V 0.438,0.76 1.385,1.385 0.948,0.625 10 false Approximately DC 177.6 V 0.063,1.802 1.073,2.708 1.01,0.906 10 false HV Battery: Nominal Voltage of DC 177.6 V 2.01,2.167 3.083,2.365 1.073,0.198 10 false Reactor 3.042,3.042 3.917,3.24 0.875,0.198 10 false Boost IPM 5.833,3.042 6.333,3.208 0.5,0.167 10 false Inverter 1.833,3.083 3.365,3.281 1.531,0.198 10 false IGBT2: OFF 5.01,3.125 6.385,3.323 1.375,0.198 10 false Capacitor



k.

DC-DC Converter Control

i.

The DC-DC converter steps down the HV battery nominal voltage of DC 177.6 V to approximately DC 14 V in order to supply electricity to the electrical components, as well as to recharge the auxiliary battery.


ii.

In order to regulate the output voltage from the DC-DC converter, the hybrid vehicle control ECU transmits an output voltage request signal to the DC-DC converter in response to battery state sensor assembly signals.

W131744E05
3.344,3.573 3.177,3.573 3.177,3.573 3.073,3.146 true 0.521,1.125 1.25,1.448 0.729,0.323 10 false HV Battery 1.604,1.063 2.688,1.563 1.083,0.5 10 false DC-DC Converter 1.823,2.969 2.625,3.271 0.802,0.302 10 false MG ECU 2.99,0.156 5.438,0.448 2.448,0.292 10 false Inverter with Converter Assembly 4.031,0.698 5.063,0.99 1.031,0.292 10 false Electrical Loads 3.917,1.677 5.25,2.063 1.333,0.385 10 false Battery State Sensor Assembly 4.688,2.438 5.271,2.646 0.583,0.208 10 false LIN 3.677,2.781 5.438,3.021 1.76,0.24 10 false Hybrid Vehicle Control ECU 3.417,3.49 5.677,3.781 2.26,0.292 10 false CAN Communication Line 6.26,1.813 6.854,2.188 0.594,0.375 10 false Auxiliary Battery



l.

System Main Relay Control

i.

The hybrid vehicle control ECU controls the system main relays to connect and disconnect the high-voltage circuit from the HV battery. The hybrid vehicle control ECU also uses the timing of the operation of the system main relays to monitor the operation of the relay contacts.


ii.

A total of 3 relays, 1 for the positive side (SMRB), and 2 for the negative side (SMRP, SMRG), are provided to ensure proper operation.

W145442E01
0.542,0.635 2.219,0.99 1.677,0.354 10 false Battery ECU Assembly 3.875,0.646 5.646,0.906 1.771,0.26 10 false Hybrid Vehicle Control ECU 2.323,1.063 3.635,1.5 1.313,0.438 10 false CAN Communication Line 0.115,3.177 0.854,3.531 0.74,0.354 10 false HV Battery 1.417,2.698 3.177,3.021 1.76,0.323 10 false Battery Current Sensor 2.688,3.542 3.344,3.917 0.656,0.375 10 false Precharge Resistor 4.219,2.833 4.854,3.198 0.635,0.365 10 false SMRB 4.219,3.719 4.854,4.083 0.635,0.365 10 false SMRP 4.219,4.604 4.854,4.969 0.635,0.365 10 false SMRG 1.51,5.01 4.375,5.333 2.865,0.323 10 false No. 1 Traction Battery Device Box Assembly 5.958,4.104 6.979,4.656 1.021,0.552 10 false To Power Cable (HV Floor Under Wire) 5.917,2.281 6.938,2.833 1.021,0.552 10 false To Power Cable (HV Floor Under Wire)


iii.

When the hybrid system changes to the READY-on state, the hybrid vehicle control ECU turns on SMRB and SMRP in sequence, and applies the current through the precharge resistor. After that, it turns SMRG on, and applies the current by bypassing the precharge resistor. Then it turns SMRP off. As the controlled current is initially allowed to pass through the precharge resistor in this manner, the contact point in the circuit is protected from damage that could be caused by an inrush current.

W131759E01
1.563,0.958 2.792,1.156 1.229,0.198 10 false SMRB: ON 1.521,1.656 2.75,1.854 1.229,0.198 10 false SMRP: OFF 1.552,2.344 2.781,2.542 1.229,0.198 10 false SMRG: OFF 5.344,0.948 6.573,1.146 1.229,0.198 10 false SMRB: ON 5.323,2.323 6.552,2.521 1.229,0.198 10 false SMRG: OFF 5.323,1.677 6.552,1.875 1.229,0.198 10 false SMRP: ON 1.604,3.802 2.833,4 1.229,0.198 10 false SMRB: ON 1.594,4.469 2.823,4.667 1.229,0.198 10 false SMRP: ON 1.594,5.167 2.823,5.365 1.229,0.198 10 false SMRG: ON 5.375,3.802 6.604,4 1.229,0.198 10 false SMRB: ON 5.354,4.49 6.583,4.688 1.229,0.198 10 false SMRP: OFF 5.365,5.177 6.594,5.375 1.229,0.198 10 false SMRG: ON


iv.

When the hybrid system changes to a state other than the READY-on state, the hybrid vehicle control ECU turns SMRG off first. Next, it turns SMRB off after determining whether or not SMRG is operating properly. After that, it turns on SMRP and then off after determining whether or not SMRB is operating properly. As a result, the hybrid vehicle control ECU verifies that the respective relays have been properly turned off.

W131760E01
1.604,0.917 2.833,1.115 1.229,0.198 10 false SMRB: ON 1.604,1.594 2.833,1.792 1.229,0.198 10 false SMRP: OFF 1.573,2.26 2.802,2.458 1.229,0.198 10 false SMRG: OFF 1.615,3.76 2.844,3.958 1.229,0.198 10 false SMRB: OFF 1.635,4.438 2.865,4.635 1.229,0.198 10 false SMRP: ON 1.594,5.104 2.823,5.302 1.229,0.198 10 false SMRG: OFF 5.354,0.896 6.583,1.094 1.229,0.198 10 false SMRB: OFF 5.385,1.594 6.615,1.792 1.229,0.198 10 false SMRP: OFF 5.375,2.271 6.604,2.469 1.229,0.198 10 false SMRG: OFF 5.354,3.76 6.583,3.958 1.229,0.198 10 false SMRB: OFF 5.354,4.427 6.583,4.625 1.229,0.198 10 false SMRP: OFF 5.344,5.104 6.573,5.302 1.229,0.198 10 false SMRG: OFF



m.

Cooling System Control for Inverter with Converter Assembly

i.

The hybrid vehicle control ECU receives signals from the temperature sensors for the inverter with converter assembly, temperature sensor for MG1 and temperature sensor for MG2. Then, the hybrid vehicle control ECU uses the duty cycle control to operate the inverter water pump with motor assembly, in order to cool the inverter with converter assembly, MG1 and MG2.


ii.

When the HV coolant temperature rises above a certain level, the hybrid vehicle control ECU transmits a radiator fan drive request signal to the ECM. In response to that signal, the ECM actuates the radiator fan to restrain the HV coolant temperature increase, ensuring the cooling of the inverter with converter assembly, MG1 and MG2.


iii.

The MG ECU converts the temperature sensor signals into digital signals, and transmits them to the hybrid vehicle control ECU via serial communication.

W145443E01
0.406,0.26 0.917,0.5 0.51,0.24 10 false ECM 0.375,0.583 1.875,0.906 1.5,0.323 10 false - Radiator Fan Control 1.25,1.344 2.917,1.688 1.667,0.344 10 false CAN Communication Line 2.917,0.427 3.667,0.76 0.75,0.333 10 false MG ECU 4.177,0.396 6.594,0.833 2.417,0.438 10 false Temperature Sensor (4 Module Temperature/HV Coolant Temperature) 4.177,1.354 6.615,1.615 2.438,0.26 10 false Inverter with Converter Assembly 1.094,2.333 2.885,2.583 1.792,0.25 10 false Hybrid Vehicle Control ECU 4.5,2.271 6.583,2.521 2.083,0.25 10 false Temperature Sensor (for MG1) 4.5,2.802 6.583,3.052 2.083,0.25 10 false Temperature Sensor (for MG2) 4.438,3.365 6.771,3.615 2.333,0.25 10 false Hybrid Vehicle Transaxle Assembly 0.792,4.531 1.375,5.031 0.583,0.5 10 false Auxiliary Battery 2.49,4.219 3.573,4.719 1.083,0.5 10 false Motor Controller 3.125,5.167 5.792,5.542 2.667,0.375 10 false Inverter Water Pump with Motor Assembly 0.823,3.792 2.031,4.115 1.208,0.323 10 false IGCT-MAIN Relay



n.

Cooling System Control for HV Battery

i.

The battery ECU assembly receives signals from the HV battery temperature sensors and HV battery intake air temperature sensor. The battery ECU assembly detects the blower speed feedback frequency, which is necessary to perform the cooling system control. Then, the battery ECU assembly steplessly actuates the battery cooling blower assembly using duty cycle control, in order to maintain the HV battery temperature within the specified range.


ii.

The battery ECU assembly converts the HV battery related signals (SOC, voltage, current and temperature) into digital signals, and transmits them to the hybrid vehicle control ECU via CAN communication.

W145444E01
4.125,0.552 4.302,0.552 4.302,0.552 4.302,1.021 false 5.083,0.271 6.625,0.719 1.542,0.448 10 false HV Battery Temperature Sensors (6) 0.552,2.021 2.292,2.281 1.74,0.26 10 false Hybrid Vehicle Control ECU 2.76,0.469 4.094,0.885 1.333,0.417 10 false HV Battery Intake Air Temperature Sensor 0.417,0.719 2.667,1.135 2.25,0.417 10 false Air Conditioning Amplifier Assembly 4.021,2.042 6.771,2.458 2.75,0.417 10 false Battery ECU Assembly 1.521,1.51 3.771,1.927 2.25,0.417 10 false CAN Communication Line 1.354,4.167 2.885,4.365 1.531,0.198 10 false IGCT Relay 0.75,4.583 2.281,4.781 1.531,0.198 10 false Auxiliary Battery 3.677,4.063 5.208,4.26 1.531,0.198 10 false Motor Controller 4.427,4.958 6.594,5.208 2.167,0.25 10 false Battery Cooling Blower Assembly 2.531,2.479 3.844,2.927 1.313,0.448 10 false CAN Communication Line



o.

Regenerative Braking Cooperative Control

i.

The skid control ECU calculates the total braking force needed based on the brake regulator pressure and brake pedal stroke when the driver depresses the brake pedal.


ii.

After calculating the required total braking force, the skid control ECU sends a regenerative braking force request to the hybrid vehicle control ECU. The hybrid vehicle control ECU replies with the amount of actual regenerative braking (regenerative braking control value).


iii.

The hybrid vehicle control ECU uses MG2 to create the negative torque (deceleration force), thus carrying out regenerative braking.


iv.

The skid control ECU controls the brake actuator solenoid valves and generates wheel cylinder pressure. The pressure that is generated is what remains after the actual regenerative braking control value has been subtracted from the required total braking force.

W131741E05
2.719,0.26 4.448,0.635 1.729,0.375 10 false Hybrid Vehicle Control ECU 5.344,0.25 6.719,0.615 1.375,0.365 10 false Hybrid Motor Control Inverter Assembly 5.698,1.26 6.313,1.604 0.615,0.344 10 false MG ECU 0.323,0.813 2.021,1.063 1.698,0.25 10 false Battery ECU Assembly 0.281,1.146 1.677,1.677 1.396,0.531 10 false - HV Battery Condition (Voltage, Current, Temperature) 2.875,1.292 4.292,1.833 1.417,0.542 10 false MG2 Generation Force (Regenerative Braking Force) Calculation 5.49,2.323 6.104,2.667 0.615,0.344 10 false MG1 6.198,2.323 6.813,2.667 0.615,0.344 10 false MG2 0.813,2.781 3.094,3 2.281,0.219 10 false Regenerative Brake Force Request 3.844,2.771 6.604,3.052 2.76,0.281 10 false Actual Regenerative Braking Control Value 0.313,3.167 2.5,3.521 2.188,0.354 10 false Brake Booster with Master Cylinder Assembly 3.073,3.542 4.313,3.813 1.24,0.271 10 false Skid Control ECU 0.406,3.958 2.063,4.344 1.656,0.385 10 false Stroke Simulator Pressure Sensor 2.74,4.156 4.458,4.521 1.719,0.365 10 false Required Total Brake Force Calculation 5.385,4.333 6.615,4.708 1.229,0.375 10 false Brake Pedal Stroke Sensor Assembly 0.5,4.927 1.917,5.292 1.417,0.365 10 false Accumulator Pressure Sensor 0.479,5.865 2.021,6.219 1.542,0.354 10 false Servo Pressure Sensor 0.688,6.792 2.229,7.146 1.542,0.354 10 false Solenoid Valves 2.75,5.156 4.354,5.542 1.604,0.385 10 false Regenerative Brake Force Request Calculation 2.771,6.177 4.344,6.573 1.573,0.396 10 false Required Hydraulic Brake Force Calculation 5.5,6.021 6.729,6.396 1.229,0.375 10 false Speed Sensors 0.625,7.448 2.917,7.833 2.292,0.385 10 false : CAN communication line



p.

Drive Start Control

·

When abnormal driver accelerator pedal and shift operations are detected, the system limits the hybrid system output and informs the driver.

W141207E02
0.229,0.229 1.677,0.677 1.448,0.448 10 false Accelerator Pedal (with Sensor) Rod Assembly 0.24,1.135 1.99,1.396 1.75,0.26 10 false Shift Lever Position Sensor 0.24,2.052 1.156,2.552 0.917,0.5 10 false MG2 Rotation Sensor 1.76,2.052 2.417,2.354 0.656,0.302 10 false MG ECU 0.26,2.979 1.854,3.26 1.594,0.281 10 false Airbag ECU Assembly 0.26,3.896 1.479,4.115 1.219,0.219 10 false Skid Control ECU 3.542,1.969 4.49,2.49 0.948,0.521 10 false Hybrid Vehicle Control ECU 5.396,0.229 6.938,0.563 1.542,0.333 10 false Multi-information Display 5.417,1.875 6.854,2.302 1.438,0.427 10 false Headup Display (Meter Mirror Sub-assembly)* 5.396,3.875 6.948,4.281 1.552,0.406 10 false Hybrid System Output 0.188,5.083 2.24,5.375 2.052,0.292 10 false *: Models with Headup Display

CAUTION:

When the system is operating, even if the driver depresses and holds the accelerator pedal, hybrid system output may increase on an uphill slope and decrease on a downhill slope. This behavior allows the system to restrict the vehicle speed and acceleration below the predetermined limit on slopes and is not a malfunction.



i.

Shift Change Control

·

Responds to shift operations with the accelerator pedal depressed.

·

Changes the limit amount according to the shift operation pattern.

·

Corrects hybrid system output according to the road grade.


Control Start Conditions (When the conditions of either pattern A or pattern B are met, control starts.) Pattern A (When all of the following conditions are met, control starts.)
·

Accelerator opening angle is approximately 1/5 or higher.

·

Shift state is changed from P to D/B, or P to R.


Pattern B (When all of the following conditions are met, control starts.)
·

Accelerator opening angle is approximately 1/5 or higher.

·

Shift state is changed from R to D/B, or D/B to R, or N to R.


Control Operation Restricts the hybrid system output so the vehicle speed and acceleration are at or below a certain level.
Control Stop Conditions (Control stops when any of the conditions are met.)
·

Accelerator pedal is fully released.

·

Shift state is P or N.



W134594E07
3.073,0.979 4.667,0.625 4.667,0.625 4.833,0.625 true 2.458,1.719 4.76,1.229 4.76,1.229 4.927,1.229 true 4.188,3.052 4.76,2.5 4.76,2.5 4.927,2.5 true 4,3.5 5.063,3.063 5.063,3.063 5.229,3.063 true 4.344,3.958 4.667,3.729 4.667,3.729 4.833,3.729 true 4.948,0.542 6.75,0.865 1.802,0.323 10 false Shift operation of pattern A or pattern B 4.969,1.146 6.74,1.521 1.771,0.375 10 false Accelerator pedal is open by approximately 1/5 or more. 4.99,2.406 6.885,2.76 1.896,0.354 10 false Without Control 4.938,3.646 6.833,4 1.896,0.354 10 false With Control * 5.292,2.979 6.354,3.333 1.063,0.354 10 false Restricted 4.417,4.156 7.031,4.677 2.615,0.521 10 false *: The hybrid system output restricted level differs between pattern A and pattern B. 2.958,4.146 4.104,4.396 1.146,0.25 10 false Time 2.781,2.51 3.927,2.76 1.146,0.25 10 false Activated 1.281,3.25 2.24,3.656 0.958,0.406 10 false Hybrid System Output 0.781,1.938 2.521,2.167 1.74,0.229 10 false Accelerator Pedal OFF 0.865,1.635 2.604,1.865 1.74,0.229 10 false Accelerator Pedal ON 1.01,1.177 2.75,1.406 1.74,0.229 10 false Shift Lever Position

HINT:
·

The hybrid system output restraint level differs between pattern A and pattern B.

·

During control while a shift operation is performed (from control start until the accelerator pedal is released), the system informs the driver of the control via the combination meter assembly and headup display (meter mirror sub-assembly)*.

·

When the VSC OFF switch is operated to turn the TRC off, the system does not operate.


*: Models with headup display



ii.

Control during Reverse Operation

·

Responds to excessive depression of the accelerator pedal while operating in reverse.

·

Corrects hybrid system output according to the road grade.


Control Start Conditions (When all of the following conditions are met, control starts.)
·

Shift state is R.

·

Accelerator pedal is depressed excessively.


Control Operation Restricts the hybrid system output so the vehicle speed and acceleration are at or below a certain level.
Control Stop Conditions (Control stops when any of the conditions are met.)
·

Accelerator pedal is fully released.

·

Shift state is not R.



W134595E09
4.208,1.344 5.083,1 5.083,1 5.25,1 true 4.552,3.552 5.104,3.365 5.104,3.365 5.271,3.365 true 4.25,3.198 5.073,2.958 5.073,2.958 5.24,2.958 true 4.594,2.917 5.073,2.615 5.073,2.615 5.24,2.615 true 5.323,0.917 7.031,1.458 1.708,0.542 10 false When the accelerator pedal is suddenly depressed. 5.323,2.552 6.958,2.906 1.635,0.354 10 false Without Control 5.313,2.875 6.948,3.229 1.635,0.354 10 false Restricted 5.323,3.281 6.958,3.635 1.635,0.354 10 false With Control 3.688,4.021 5.323,4.375 1.635,0.354 10 false Time 1.531,3.021 2.448,3.469 0.917,0.448 10 false Hybrid system output 2.906,2.396 4.542,2.75 1.635,0.354 10 false Activated 1.021,1.635 2.656,1.99 1.635,0.354 10 false Accelerator Pedal OFF 1.104,1.229 2.74,1.583 1.635,0.354 10 false Accelerator Pedal ON 1.229,0.75 2.865,1.104 1.635,0.354 10 false Shift Lever Position 2.76,0.781 4.396,1.135 1.635,0.354 10 false R




FUNCTION


a.

Drive Mode Select

i.

By pressing the drive mode select switch (combination switch assembly), the driving mode can be changed to "Eco", "Normal" or "Power" accordingly.


ii.

If the ignition switch is turned off with "Normal" or "Eco" mode selected, the latest mode will maintained when the ignition switch is turned to ON. However, if "Power" mode is selected when the ignition switch is turned off, the drive mode will change to "Normal" mode when the ignition switch is turned to ON.




DIAGNOSIS


a.

When the hybrid vehicle control ECU detects a malfunction in the hybrid system, the hybrid vehicle control ECU performs diagnosis and memorizes information related to the fault. To inform the driver of the malfunction, the hybrid vehicle control ECU illuminates or blinks the Malfunction Indicator Lamp (MIL). At the same time, a Diagnostic Trouble Code (DTC) is stored in memory.


b.

3-digit information codes (INF codes) are provided with a conventional DTC as a subset of the primary 5-digit code. This enables the troubleshooting procedure to further narrow down the possible trouble areas to identify the problem.


c.

DTCs can be read by connecting the Global TechStream (GTS) to the DLC3. For details, refer to the Repair Manual.