Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
NM36W0E _51 Engine / Hybrid System _088520 HYBRID / BATTERY CONTROL _0421728 HYBRID CONTROL SYSTEM GE GENERAL F

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  GENERAL  GENERAL  


OUTLINE


a.

The hybrid system of this hybrid vehicle employs the Toyota Hybrid System-II (THS-II) under the "Hybrid Synergy Drive" concept*.

HINT:

*: The "Hybrid Synergy Drive" concept consists of 4 key benefits: Fuel efficiency, low emissions, seamless acceleration, and silent performance.



b.

Hybrid vehicles use a combination of 2 kinds of power sources, such as an engine and HV battery, so as to take advantage of the benefits provided by each power source while compensating for each other's shortcomings. As a result, efficient operation is achieved.


c.

Hybrid vehicles do not need their batteries to be charged externally unlike existing electric-only vehicles. Therefore, special infrastructure is not required to use hybrid vehicles.


d.

Technical development of power sources (such as engines and fuel cells) is advancing in various fields. The hybrid system is a flexible system that uses a high-efficiency power unit and electric motors.


e.

Hybrid vehicles have high-voltage electrical circuits. Hybrid vehicles have been developed with consideration given to the protection of drivers and technicians against electrocution.



SPECIFICATION


a.

Motor Generator

Item Specification
MG1 MG2
Type Permanent Magnet Motor Permanent Magnet Motor
Function Generate, Engine Starter Generate, Drive Wheels
Maximum System Voltage V DC 580 DC 580
Maximum Output kW (HP) - 59 (79)
Maximum Torque N*m (ft.*lbf) - 141 (104)
Cooling System Water-cooled Water-cooled


b.

Inverter with Converter Assembly

Item Specification
Boost Converter Rated Voltage (Inverter Side) V DC 580
Rated Voltage (HV Battery Side) V DC 177.6
DC-DC Converter Rated Output Voltage V DC 11 to 15
Maximum Output Current A 100


c.

Cooling System (for Inverter with Converter Assembly and Hybrid Vehicle Transaxle Assembly)

Item Specification
Inverter Water Pump with Motor Assembly Motor Type Brushless
Discharge Volume Liter (US qts, Imp. qts) 12 (12.7, 10.6)/min. or greater
Coolant Type Toyota Genuine Super Long Life Coolant (SLLC)
Color Pink
Capacity Liter (US qts, Imp. qts) 1.4 (1.5, 1.2)
Maintenance Intervals First Time km (miles) 240000 (150000)
Subsequent km (miles) Every 80000 (50000)



MAIN FEATURES


a.

The THS-II control has the following features.

Features Outline
Idle Stop Idling of the engine is automatically stopped (idle stop) to reduce energy loss.
EV Drive
(Efficient Drive Control)
This allows the vehicle to be driven using only the electric motor when engine efficiency is low. Additionally, electricity is generated when engine efficiency is high. Control is performed to maximize the total efficiency of the vehicle.
EV Drive Mode If the driver operates the switch and the operating conditions are being met, the vehicle can run on only the electric motor.
Motor Assist The electric motor supplements the engine power when accelerating.
Regenerative Braking
(Energy Regeneration)
During deceleration and while depressing the brake pedal, part of the energy that normally would be lost as heat is collected as electrical energy to be reused, such as for motor power.


b.

The mechanism of the THS-II is as follows.

i.

The THS-II consists of mainly the engine, hybrid vehicle transaxle assembly, inverter with converter assembly and HV battery, and employs a series/parallel-type hybrid system.

W101195C07
2.479,1.156 2.76,1.354 0.281,0.198 10 false *1 1.521,1.708 1.802,1.906 0.281,0.198 10 false *2 3.24,1.813 3.521,2.01 0.281,0.198 10 false *3 2.479,2.479 2.76,2.677 0.281,0.198 10 false *4 2.458,1.75 2.74,1.948 0.281,0.198 10 false *5 2.458,1.948 2.74,2.146 0.281,0.198 10 false *6 3.458,2.49 3.74,2.688 0.281,0.198 10 false *7 4.521,2.469 4.802,2.667 0.281,0.198 10 false *8
*1 Engine *2 Hybrid Vehicle Transaxle Assembly
*3 Motor Generator No. 1 (MG1) *4 Motor Generator No. 2 (MG2)
*5 Power Split Planetary Gear Unit (Compound Gear Unit) *6 Motor Speed Reduction Gear Unit (Compound Gear Unit)
*7 Inverter with Converter Assembly *8 HV Battery
V100143

Electrical Power Path (DC)
V100155

Electrical Power Path (AC)
V100144

Mechanical Power Path - -


HINT:

Generally, there are 3 types of hybrid systems: series-type hybrid system, parallel-type hybrid system and series/parallel-type hybrid system.


·

In a series-type hybrid system, the motor rotates the wheels, and the engine, using a generator, acts as an electric power source for the motor.

W101596C02
1.042,1.313 1.313,1.51 0.271,0.198 10 *1 2.01,1.313 2.281,1.51 0.271,0.198 10 *2 3.604,1.323 3.875,1.521 0.271,0.198 10 *4 3.604,0.802 3.875,1 0.271,0.198 10 *3 5.167,1.323 5.438,1.521 0.271,0.198 10 *5
*1 Engine *2 Generator
*3 Inverter *4 HV Battery
*5 Motor - -
V100143

Electrical Power Path (DC)
V100155

Electrical Power Path (AC)
V100144

Mechanical Power Path - -


·

In a parallel-type hybrid system, both the engine and the motor generator directly rotate the wheels. In addition to supplementing the power of the engine, the motor generator can also serve as a generator to charge the HV battery while the vehicle is in motion. Driving the vehicle only with the motor generator is also possible.

W101597C02
3.073,0.792 3.344,0.99 0.271,0.198 10 *1 3.75,0.792 4.021,0.99 0.271,0.198 10 *2 1.146,1.854 1.417,2.052 0.271,0.198 10 *3 2.333,1.875 2.604,2.073 0.271,0.198 10 *4 3.802,1.854 4.073,2.052 0.271,0.198 10 *5
*1 Engine *2 Transmission
*3 HV Battery *4 Inverter
*5 Motor Generator - -
V100143

Electrical Power Path (DC)
V100155

Electrical Power Path (AC)
V100144

Mechanical Power Path - -


·

In a series/parallel-type hybrid system, aspects of both a series-type hybrid system and a parallel-type hybrid system are combined. The system has 2 motor generators. Electricity can be generated by motor generator No. 1 using engine power. The generated electricity is used to charge the HV battery and also to power motor generator No. 2.

W101598C02
4.906,0.667 5.177,0.865 0.271,0.198 10 *1 1.146,1.615 1.417,1.813 0.271,0.198 10 *3 2.354,1.604 2.625,1.802 0.271,0.198 10 *4 4.948,2.01 5.219,2.208 0.271,0.198 10 *6 3.813,1.24 4.083,1.438 0.271,0.198 10 *5 4.917,1.229 5.188,1.427 0.271,0.198 10 *2
*1 Engine *2 Power Split Planetary Gear Unit
*3 HV Battery *4 Inverter
*5 Motor Generator No. 1 (MG1) *6 Motor Generator No. 2 (MG2)
V100143

Electrical Power Path (DC)
V100155

Electrical Power Path (AC)
V100144

Mechanical Power Path - -




ii.

The system optimally performs cooperative control of the high-output M15A-FXE engine and the high-speed, high-output Motor Generator No. 1 (MG1) and Motor Generator No. 2 (MG2) in the P910 hybrid transaxle that provides excellent transmission performance.


iii.

The system has 2 batteries, which are used for different purposes. One is the HV battery (nominal voltage of DC 177.6 V) which stores electrical power to drive the vehicle, and the other is the auxiliary battery (nominal voltage of DC 12 V) which supplies electrical power to the electrical components.


iv.

Furthermore, this system uses a variable-voltage system consisting of the high-output HV battery (nominal voltage of DC 177.6 V), a boost converter that boosts the operating voltage of MG1 and MG2 to a maximum voltage of DC 580 V, and an inverter which converts direct current and alternating current.


v.

Since hybrid vehicles are not equipped with a conventional alternator, the high-voltage from the HV battery is stepped down to approximately DC 14 V using a DC-DC converter in order to charge the auxiliary battery. Also, the HV battery regularly charges and discharges within the constant State of Charge (SOC) range while the vehicle is running, thus, recharging from external power sources is not necessary.

W145377C01
1.844,2.896 2.583,0.51 2.583,0.51 2.75,0.51 true 1.531,2.625 0.979,1.74 0.979,1.74 0.813,1.74 true 4.458,2.625 5.188,3.635 5.188,3.635 5.354,3.635 true 1.896,3.49 1.5,4.25 1.5,4.25 1.333,4.25 true 4.031,2.198 4.74,0.333 4.74,0.333 4.906,0.333 true 0.625,1.646 0.938,1.802 0.313,0.156 10 false *1 2.813,0.417 3.125,0.573 0.313,0.156 10 false *2 4.969,0.24 5.281,0.396 0.313,0.156 10 false *3 1.156,4.167 1.469,4.323 0.313,0.156 10 false *5 5.396,3.542 5.844,3.74 0.448,0.198 10 false *4
*1 M15A-FXE Engine *2 Inverter with Converter Assembly
·

Inverter

·

Boost Converter

·

DC-DC Converter


*3 Auxiliary Battery *4 HV Battery
*5 P910 Hybrid Vehicle Transaxle Assembly
·

Motor Generator No. 1 (MG1)

·

Motor Generator No. 2 (MG2)


- -



vi.

A cooling system that is independent from the engine cooling system is provided to cool the inverter with converter assembly and ATF.

W145117C01
4.854,2.76 5.49,3.813 5.49,3.813 5.656,3.813 true 3.667,3.417 3.833,3.417 3.833,3.417 4.677,3.177 true 3.313,1.51 2.792,1.021 2.792,1.021 2.625,1.021 true 3.813,0.99 3.479,0.365 3.479,0.365 3.313,0.365 true 5.667,1.208 5.917,0.25 5.917,0.25 6.083,0.25 true 2.406,4.156 2.583,4.448 2.583,4.448 2.771,4.448 true 2.438,0.948 2.75,1.104 0.313,0.156 10 false *1 3.125,0.281 3.438,0.438 0.313,0.156 10 false *2 6.135,0.167 6.448,0.323 0.313,0.156 10 false *3 3.51,3.333 3.823,3.49 0.313,0.156 10 false *4 5.719,3.719 6.031,3.875 0.313,0.156 10 false *5 2.844,4.354 3.156,4.51 0.313,0.156 10 false *4
*1 Radiator Assembly *2 Inverter Reserve Tank Assembly
*3 Inverter with Converter Assembly
·

Inverter

·

Boost Converter

·

DC-DC Converter


*4 Inverter Water Pump with Motor Assembly
*5 Motor Cooling Cooler - -
V100135

HV Coolant Flow - -





PRECAUTION


a.

Hybrid Vehicle High-voltage Safety Measures

i.

High-voltage safety is comprised of 2 points: "Insulation of High-voltage Circuits" and "Cut-off of High-voltage Circuits". The hybrid system also detects whether or not a decrease in insulation resistance has occurred between the high-voltage system and body ground.



b.

Insulation of High-voltage Circuits

i.

High-voltage circuits are used between the HV battery, inverter with converter assembly, hybrid vehicle transaxle assembly and compressor with motor assembly. Each of these items is connected by the power cable and is electrically insulated using cases and covers.


ii.

The power cable is also shielded using a mesh conductor built into the electrical insulation of the wires. The shielding is grounded to the chassis of the vehicle and its main purpose is to prevent electromagnetic interference.

W145429C01
1.281,1.406 1.281,0.281 1.281,0.281 1.542,0.281 true 4.667,1.635 5.125,0.26 5.125,0.26 5.385,0.26 true 3.729,2.427 4.26,3.521 4.26,3.521 4.521,3.521 true 1.906,2.375 2.333,3.552 2.333,3.552 2.594,3.552 true 0.49,3.479 0.771,3.479 0.771,3.479 1.406,2.292 true 0.365,0.719 0.646,0.719 0.646,0.719 1.26,1.938 true 0.198,0.615 0.51,0.771 0.313,0.156 10 false *1 1.604,0.188 1.917,0.344 0.313,0.156 10 false *2 5.448,0.167 5.76,0.323 0.313,0.156 10 false *3 4.573,3.427 4.885,3.583 0.313,0.156 10 false *4 2.646,3.448 2.958,3.604 0.313,0.156 10 false *5 0.323,3.396 0.635,3.552 0.313,0.156 10 false *6
*1 Power Cable (HV Air Conditioning Wire) *2 Compressor with Motor Assembly
*3 HV Battery *4 Power Cable (HV Floor Under Wire)
*5 Hybrid Vehicle Transaxle Assembly *6 Inverter with Converter Assembly




c.

Cut-off of High-voltage Circuits

i.

When any of the conditions below occur, the System Main Relays (SMRs) are automatically shut off by the hybrid vehicle control ECU.

·

The ignition switch is turned off.

·

Any airbag is deployed.

·

inverter cover sub-assembly upper is removed (interlock circuit is opened).

·

Service plug grip handle is unlocked (interlock circuit is opened).

·

A specified malfunction occurs.


W145430E01
0.406,6.344 0.406,7.135 0.406,7.135 0.573,7.135 true 0.125,1 1.729,1.385 1.604,0.385 10 false Power Switch (Push Start Switch)*2 0.167,1.833 1.688,2.208 1.521,0.375 10 false Certification ECU (Smart Key ECU Assembly)*2 0.167,2.625 1.573,2.844 1.406,0.219 10 false Airbag ECU Assembly 2.625,1.75 4.021,2.104 1.396,0.354 10 false Hybrid Vehicle Control ECU 0.625,7.031 1.646,7.219 1.021,0.188 10 false Interlock Switch 0.656,6.552 1.781,7.01 1.125,0.458 10 false Service Plug Grip 0.896,4.5 1.615,4.719 0.719,0.219 10 false HV Battery 0.542,7.448 2.25,7.656 1.708,0.208 10 false : CAN communication line 3.01,4.469 3.438,4.656 0.427,0.188 10 false SMRB 3,5.552 3.427,5.74 0.427,0.188 10 false SMRP 3.01,6.719 3.51,6.906 0.5,0.188 10 false SMRG 4.552,4.042 6.927,4.25 2.375,0.208 10 false To Power Cable (HV Floor Under Wire) 4.563,6.302 6.938,6.51 2.375,0.208 10 false To Power Cable (HV Floor Under Wire) 4.865,2.49 5.469,2.677 0.604,0.188 10 false MG ECU 5.365,1.25 7.156,1.792 1.792,0.542 10 false Interlock Switch (For Inverter Cover Sub-assembly Upper) 0.125,0.208 1.719,0.563 1.594,0.354 10 false Ignition or Starter Switch Assembly*1 3.469,7.125 6.76,7.469 3.292,0.344 10 false *1: Models without entry and start system 3.469,7.479 6.708,7.802 3.24,0.323 10 false *2: Models with entry and start system