Home › Engine / Hybrid System › M15A-FKS (ENGINE MECHANICAL) › ENGINE UNIT
NM36W0E _51 Engine / Hybrid System _088517 M15A-FKS ENGINE MECHANICAL _0421731 ENGINE UNIT DE DETAILS F

M15A-FKS ENGINE MECHANICAL  ENGINE UNIT  DETAILS  CYLINDER BLOCK  


CONSTRUCTION


a.

An aluminum cylinder block sub-assembly is used to achieve a lightweight design.


b.

The liners are a spiny-type, which have been manufactured so that their casting exteriors form large irregular surfaces in order to enhance the adhesion between the liners and the aluminum cylinder block sub-assembly. The enhanced adhesion helps heat dissipation, resulting in a lower overall temperature and reduced heat deformation of the cylinder bores.


c.

A hole is provided to introduce fresh air for the Positive Crankcase Ventilation (PCV) system into the crankcase, ensuring the performance of fresh air and blow-by gas agitation while also ensuring a sufficient area of the PCV gas passage.


d.

By positioning the water jackets adjacent to the oil drain paths, heat transfer between them has been enhanced. With this, cold engine warm-up capability is enhanced and excessive oil temperatures are reduced when the engine load is high, ensuring vehicle reliability.


e.

Cooling passages are drilled between each cylinder bore to provide increased cooling to the upper part of the cylinder bore which is most susceptible to heat. This minimizes deformation of the cylinder bore, ensuring high power output and reduced oil consumption.


f.

A larger breather hole is provided in the No. 1 to No. 3 journal wall. As a result, friction is reduced and output performance is improved.


g.

The angle of the bore cross hatching, the polishing on the cylinder liner surface, is at an angle of 30°, thus improving the oil retention of the interior of the cylinder bore. This reduces the friction between the cylinder bore and the piston, improving fuel consumption.


h.

The shape of the ribs, and the positioning and shape of the knock control sensor have been optimized, thus improving control of knocking.


i.

A gap is provided on the side surface of the crank bearing cap to prevent strong impacts to the crank bearing caused by the whirling of the crankshaft that is characteristic of in-line 3-cylinder engines, reducing friction and weight.

W145055C01
3.75,5.25 6.833,7.667 3.083,2.417 3.75,2.75 6.833,5.167 3.083,2.417 0.406,0.25 0.552,0.25 0.552,0.25 0.74,0.813 true 0.979,0.969 1.125,0.219 1.125,0.219 1.292,0.219 true 1.583,0.969 1.729,0.219 1.729,0.219 1.896,0.219 true 2.188,0.969 2.333,0.219 2.333,0.219 2.5,0.219 true 4.406,0.719 4.49,0.25 4.49,0.25 4.656,0.25 true 4.417,1.625 4.583,2.115 4.583,2.115 4.75,2.115 true 5.333,4.271 5.604,4.552 5.604,4.552 5.771,4.552 true 4.656,4.229 4.802,4.229 4.802,4.229 5.198,3.906 true 5.302,3.906 5.844,3.906 true 5.281,5.635 5.49,5.406 5.49,5.406 5.656,5.406 true 5.719,6.375 6.313,5.906 6.313,5.906 6.479,5.906 true 5.313,6.656 5.583,7.427 5.583,7.427 5.75,7.427 true 1.948,7.438 2.49,7.438 true 0.229,0.177 0.542,0.375 0.313,0.198 10 false *1 1.354,0.125 1.667,0.323 0.313,0.198 10 false *a 1.969,0.115 2.281,0.313 0.313,0.198 10 false *a 2.573,0.115 2.885,0.313 0.313,0.198 10 false *a 4.719,0.146 5.031,0.344 0.313,0.198 10 false *b 6.427,1.271 6.74,1.469 0.313,0.198 10 false 30° 5.198,0.948 5.51,1.146 0.313,0.198 10 false *c 4.813,2.021 5.125,2.219 0.313,0.198 10 false *d 1.073,4.938 1.385,5.135 0.313,0.198 10 false B 1.073,3.115 1.385,3.313 0.313,0.198 10 false B 3.823,2.813 4.135,3.01 0.313,0.198 10 false *e 3.833,5.333 4.146,5.531 0.313,0.198 10 false *i 5.885,3.802 6.198,4 0.313,0.198 10 false *f 5.833,4.458 6.146,4.656 0.313,0.198 10 false *h 4.469,4.146 4.781,4.344 0.313,0.198 10 false *g 5.708,5.313 6.021,5.51 0.313,0.198 10 false *f 6.531,5.802 6.844,6 0.313,0.198 10 false *j 5.813,7.344 6.125,7.542 0.313,0.198 10 false *k 2.542,7.344 2.854,7.542 0.313,0.198 10 false *l 0.885,1.51 1.021,1.677 0.135,0.167 10 false A 1.656,1.51 1.792,1.677 0.135,0.167 10 false A
*1 Cylinder Block Sub-assembly - -
*a Oil Drain Passage *b Cylinder Bore
*c Bore Cross Hatch *d Spiny-type Liner (Irregularly Shaped Outer Casting Surface of Liner)
*e A-A Cross Section *f Water Passage
*g Cylinder Liner Circumference Processing *h Thermal Spray Aluminum Coating
*i B-B Cross Section *j Fresh Air Introduction Hole for PCV
*k Larger Breather Hole *l Side Groove



j.

Through the use of an offset crankshaft, the centerline of the bores is shifted 10 mm (0.394 in.) towards the intake side in relation to the centerline of the crankshaft. Thus, the side force to the cylinder wall is reduced when the maximum pressure is applied. This contributes to fuel economy.

W145056C01
4.115,3.042 4.281,3.042 4.281,3.042 4.615,2.458 true 5.458,3.042 5.625,3.042 5.625,3.042 5.958,2.458 true 1.885,0.74 2.198,0.896 0.313,0.156 10 false *a 1.833,2.917 2.146,3.073 0.313,0.156 10 false *b 2.844,0.813 3.156,0.969 0.313,0.156 10 false *c 0.885,0.813 1.198,0.969 0.313,0.156 10 false *d 4.646,0.594 4.958,0.75 0.313,0.156 10 false *e 4.677,3.25 4.99,3.406 0.313,0.156 10 false *f 6,3.25 6.26,3.521 0.26,0.271 10 false *g 5.844,0.594 6.156,0.75 0.313,0.156 10 false *e 3.958,2.958 4.271,3.115 0.313,0.156 10 false *b 5.302,2.958 5.615,3.115 0.313,0.156 10 false *b
*a Bore Centerline *b Crankshaft Center
*c Intake Side *d Exhaust Side
*e Maximum Pressure *f Offset Crankshaft
*g Non-offset Crankshaft - -