Home › Engine / Hybrid System › M15A-FXE (ENGINE MECHANICAL) › ENGINE UNIT › 2020.03–2020.07
NM36W0E _51 Engine / Hybrid System _088519 M15A-FXE ENGINE MECHANICAL _0421732 ENGINE UNIT GE GENERAL F

M15A-FXE ENGINE MECHANICAL  ENGINE UNIT  GENERAL  GENERAL  


OUTLINE


a.

The M15A-FXE engine is an in-line 3-cylinder, 1.5 liter, 12 valve DOHC engine.


b.

The engine adopts the Dual Variable Valve Timing-intelligent (Dual VVT-i) system which realizes optimal valve timing by using electric motors to actuate the intake camshaft actuators and engine oil pressure to actuate the exhaust camshaft actuators. In addition, this engine uses a high-expansion ratio Atkinson cycle, Direct Ignition System (DIS), Electronic Throttle Control System-intelligent (ETCS-i) and Exhaust Gas Recirculation (EGR) system employing a highly efficient EGR cooler. Thus, improved engine performance, quietness, fuel economy and cleaner emissions have been achieved.



SPECIFICATION


Item Specification

*: The figure shown is the weight of the part without coolant and oil.

Engine Type M15A-FXE
No. of Cyls. & Arrangement 3-cylinder, In-line
Valve Mechanism 12-valve DOHC, Chain Drive
(With VVT-iE and VVT-i)
Combustion Chamber Pentroof Type
Flow of Intake and Exhaust Gasses Cross-flow
Fuel System Sequential Multiport Fuel Injection (SFI)
Ignition System Direct Ignition System (DIS)
Displacement cm3 (cu. in.) 1490 (90.9)
Bore x Stroke mm (in.) 80.5 x 97.6 (3.17 x 3.84)
Compression Ratio 14.0 : 1
Max. Output (EEC) kW@rpm 67@5500
Max. Torque (EEC) N*m@rpm 120@3800 to 4800
Valve Timing Intake Open -30° to 40° BTDC
Closed 110° to 40° ABDC
Exhaust Open 3° to 44° BBDC
Closed 41° to 0° ATDC
Spark Plug Type DENSO Made FC16HR-Q8
NGK Made DILKAR6T8
Plug Gap mm (in.) 0.7 to 0.8 (0.0276 to 0.0315)
Firing Order 1 - 2 - 3
Research Octane Number (RON) 91 or higher
Emission Regulation EURO 6b
Engine Service Mass* (Reference) kg (lb.) 87.3 (192.5)


MAIN FEATURES


a.

The M15A-FXE engine has achieved the following through the use of the items listed in the table below.

i.

High performance and reliability


ii.

Low noise and vibration


iii.

Lightweight and compact design


iv.

Good serviceability


v.

Clean emissions and improved fuel economy

Item i ii iii iv v

○: Applicable

-: Not applicable

The high-expansion ratio Atkinson cycle is adopted. ○ - - - ○
Engine Proper An aluminum cylinder block sub-assembly is used. - - ○ - -
Spiny-type liners are used in the cylinder bores. ○ - - - ○
A cylinder block water jacket spacer is used. ○ - - - ○
The piston skirt is coated with resin. ○ - - - ○
An offset crankshaft is used. ○ - - - ○
Laser cladded valve seats are used for the intake side. ○ - ○ - ○
A chain cover that consists of the timing chain cover assembly and No. 2 timing chain cover assembly is used. ○ - - - -
Bolts with smaller heads than standard bolts of the same thread diameter are used. ○ - ○ - -
Valve Mechanism The Variable Valve Timing-intelligent by Electric motor (VVT-iE) system is used for the intake camshaft sub-assembly. ○ - - - ○
The Variable Valve Timing-intelligent (VVT-i) system is used for the exhaust camshaft sub-assembly. ○ - - - ○
A chain sub-assembly and No. 1 chain tensioner assembly are used. - - ○ ○ -
Valve lash adjuster assemblies are used. ○ ○ ○ ○ ○
No. 1 valve rocker arm sub-assemblies are used. ○ - ○ - ○
Lubrication System A cartridge type oil filter sub-assembly is used. - - - ○ -
An engine oil level sensor is used. - - - - ○
Cooling System TOYOTA Genuine Super Long Life Coolant (SLLC) is used. - - - ○ -
An electric engine water pump is used. ○ ○ ○ - ○
Intake and Exhaust System An intake manifold made of plastic is used. ○ ○ ○ - -
A linkless type throttle body with motor assembly is used. ○ ○ ○ ○ ○
A stainless steel exhaust manifold is used. ○ - ○ - ○
Emission Control System A step motor type Exhaust Gas Recirculation (EGR) valve is used. ○ - - - ○
A water-cooled type Exhaust Gas Recirculation (EGR) cooler is used. ○ - - - ○
An ultra thin-wall, high-cell density ceramic type Three-Way Catalytic converter (TWC) is used. - - - - ○
Fuel System A fuel returnless system is used. - - ○ ○ ○
Quick connectors are used to connect the fuel hoses with the fuel pipes. - - - ○ -
10-hole type fuel injector assemblies are used. ○ - ○ - ○
Ignition System Long-reach type iridium-tipped spark plugs are used. ○ - - ○ ○
Engine Control System Magnetic Resistance Element (MRE) type camshaft position sensors and crank position sensor are used. ○ - - - ○
The Electronic Throttle Control System-intelligent (ETCS-i) is used. ○ - - - ○
An evaporative emission control system is used. - - - - ○



b.

Location of small-head bolts

W145739

W145110

W145111