Home › Engine / Hybrid System › CRUISE CONTROL › SPEED LIMITER SYSTEM › from 2020.07
NM36W0E _51 Engine / Hybrid System _087276 CRUISE CONTROL _0432791 SPEED LIMITER SYSTEM CO CONTROL F

CRUISE CONTROL  SPEED LIMITER SYSTEM  CONTROL  SPEED LIMITER CONTROL  


FUNCTION OF MAIN COMPONENTS


a.

The main components in the speed limiter system have the following functions:

Gasoline Models
Component Function

*1: Models with manual transaxle

*2: Models with CVT

Steering Pad Switch Assembly Speed Limiter Switch Turns speed limiter control on and off.
CANCEL Switch A cancel signal is output to the ECM when this switch is operated.
+RES Switch Increases the limit speed or resumes a preset limit speed.
-SET Switch The deceleration function and set control function can be performed by operating this switch. A signal is output to the ECM when this switch is operated.
Stop Light Switch Assembly Detects the depressing of the brake pedal and transmits a signal to the ECM.
Accelerator Pedal Sensor Assembly Detects the accelerator pedal depression angle and transmits it to the ECM.
Clutch Switch Assembly*1 Detects the clutch pedal depression angle and transmits it to the ECM.
Throttle Body with Throttle Position Sensor Assembly Throttle Position Sensor Detects the throttle valve opening angle and outputs it to the ECM.
Throttle Control Motor Adjusts the throttle valve opening angle in accordance with signals from the ECM.
Combination Meter Assembly Speed Limiter Indicator
·

Based on a speed limiter indicator operation signal sent by the ECM, the combination meter assembly illuminates the speed limiter indicator when the speed limiter switch has been pressed to turn the speed limiter system on.

·

Based on a speed limiter indicator operation signal sent by the ECM, the combination meter assembly turns off the speed limiter indicator if a malfunction occurs in the speed limiter system.


Multi-information Display Displays a warning message to alert the driver in accordance with a signal provided by the ECM.
Buzzer If the ECM detects automatic cancel or warning signals while the vehicle is operating under speed limiter control, this buzzer sounds to inform the driver.
ECM
·

Controls the speed limiter system in accordance with signals from the switches and sensors.

·

Actuates the throttle control motor.

·

If the ECM detects a malfunction in the speed limiter system, it will store a Diagnostic Trouble Code (DTC).


Transmission Control ECU*2 Controls the CVT in accordance with signals from the ECM.
Brake Actuator Assembly Skid Control ECU Transmits the speed signal to the ECM.
Central Gateway ECU (Network Gateway ECU) Relays and transmits each CAN communication data signal.

HV Models
Component Function
Steering Pad Switch Assembly Speed Limiter Switch Turns speed limiter control on and off.
CANCEL Switch A cancel signal is output to the hybrid vehicle control ECU when this switch is operated.
+RES Switch Increases the limit speed or resumes a preset limit speed.
-SET Switch The deceleration function and set control function can be performed by operating this switch. A signal is output to the hybrid vehicle control ECU when this switch is operated.
Stop Light Switch Assembly Detects the depressing of the brake pedal and transmits a signal to the hybrid vehicle control ECU.
Combination Switch Assembly VSC OFF Switch Detects the switch operation signal and outputs it to the skid control ECU.
Accelerator Pedal Sensor Assembly Detects the accelerator pedal depression angle and transmits it to the hybrid vehicle control ECU.
Throttle Body with Throttle Position Sensor Assembly Throttle Position Sensor Detects the throttle valve opening angle and outputs it to the ECM.
Throttle Control Motor Adjusts the throttle valve opening angle in accordance with signals from the ECM.
Inverter with Converter Assembly MG ECU Controls the motive force of hybrid vehicle transaxle assembly in accordance with signals from the hybrid vehicle control ECU.
Hybrid Vehicle Transaxle Assembly Generates motive force for the front wheels.
Combination Meter Assembly Speed Limiter Indicator
·

Based on a speed limiter indicator operation signal sent by the hybrid vehicle control ECU, the combination meter assembly illuminates the speed limiter indicator when the speed limiter switch has been pressed to turn the speed limiter system on.

·

Based on a speed limiter indicator operation signal sent by the hybrid vehicle control ECU, the combination meter assembly turns off the speed limiter indicator if a malfunction occurs in the speed limiter system.


Multi-information Display Displays a warning message to alert the driver in accordance with a signal provided by the hybrid vehicle control ECU.
Buzzer If the hybrid vehicle control ECU detects automatic cancel or warning signals while the vehicle is operating under speed limiter control, this buzzer sounds to inform the driver.
Hybrid Vehicle Control ECU
·

Controls the speed limiter system in accordance with signals from the switches and sensors.

·

If the hybrid vehicle control ECU detects a malfunction in the speed limiter system, it will store a Diagnostic Trouble Code (DTC).


ECM Actuates the throttle control motor in accordance with the signals from the hybrid vehicle control ECU.
Brake Actuator Assembly Skid Control ECU Transmits the speed signal to the hybrid vehicle control ECU.
Central Gateway ECU (Network Gateway ECU) Relays and transmits each CAN communication data signal.



FUNCTION


a.

The speed limiter system has the following functions:

Gasoline Models
Function Outline

*: Models with manual transaxle

Set Control When the driver turns on the speed limiter switch, the speed limiter indicator will illuminate in the combination meter assembly. In this state, when the -SET switch is pressed, the system will memorize the speed that the vehicle was traveling at prior to the operation of the -SET switch as a limit speed, and display the limit speed on the combination meter assembly (If the -SET switch is pressed while the vehicle is being driven at 30 km/h [20 mph] or less, or while the vehicle is stopped, the system will memorize the limit speed as being approximately 30 km/h [20 mph]).
Constant Speed Control When the speed limiter control is on, the ECM will compare the actual vehicle speed with the limit speed. If the actual vehicle speed is greater than the limit speed, the ECM will control the throttle control motor in the closing direction. Thus, the system reduces the actual vehicle speed to the limit speed.
Coast Control If the driver continues to press the -SET switch, the system will reduce the limit speed in 5 km/h or 5 mph increments. The instant the driver releases the -SET switch, that speed will be rendered as the set speed.
Tap-down Control If the driver presses the -SET switch momentarily (approximately 0.6 seconds), the system will reduce the limit speed by 1 km/h or 1 mph with each press of the switch.
Accelerator Control If the driver continues to press the +RES switch, the system will increase the limit speed in 5 km/h or 5 mph increments. The instant the driver releases the +RES switch, that speed will be rendered as the limit speed.
Tap-up Control If the driver presses the +RES switch momentarily (approximately 0.6 seconds), the system will increase the limit speed by 1 km/h or 1 mph with each press of the switch.
Override Control While driving the vehicle with speed limiter system on, if the driver fully depresses the accelerator pedal, the ECM will detect that the accelerator pedal sensor assembly is in kick down mode. Then, the ECM will recognize this to be the driver's acceleration requirement, and allow the vehicle to accelerate higher than the limit speed. After the acceleration, when the vehicle speed falls below the limit speed, this function will resume limit speed control.
Cancel Control While the vehicle is being driven with the speed limiter system on, if any one of the following signals is input into the ECM, the system will cancel the speed limiter system:
·

CANCEL switch on signal (the driver has pressed the CANCEL switch).

·

Speed limiter switch off signal (deletes the limit speed).

·

Cruise control switch on signal (transfers to the constant speed control mode, turns off the speed limiter indicator, and deletes the limit speed).

·

Malfunction in the engine control system.

·

Communication malfunction between the skid control ECU and ECM.


Resume Control After turning the CANCEL switch on to turn speed limiter switch off, if the driver pushes the +RES switch, the system will limit the vehicle speed at the limit speed that was set at the time of cancelation.
Other Cancellation Items* While the clutch pedal is depressed, the system temporarily deactivates the speed limiter control.

HV Models
Function Outline
Set Control When the driver turns on the speed limiter switch, the speed limiter indicator will illuminate in the combination meter assembly. In this state, when the -SET switch is pressed, the system will memorize the speed that the vehicle was traveling at prior to the operation of the -SET switch as a limit speed, and display the limit speed on the combination meter assembly (If the -SET switch is pressed while the vehicle is being driven at 30 km/h [20 mph] or less, or while the vehicle is stopped, the system will memorize the limit speed as being approximately 30 km/h [20 mph]).
Constant Speed Control When the speed limiter control is on, the hybrid vehicle control ECU will compare the actual vehicle speed with the limit speed. If the actual vehicle speed is greater than the limit speed, the hybrid vehicle control ECU will control the engine and MG2. Thus, the system reduces the actual vehicle speed to the limit speed.
Coast Control If the driver continues to press the -SET switch, the system will reduce the limit speed in 5 km/h or 5 mph increments. The instant the driver releases the -SET switch, that speed will be rendered as the set speed.
Tap-down Control If the driver presses the -SET switch momentarily (approximately 0.6 seconds), the system will reduce the limit speed by 1 km/h or 1 mph with each press of the switch.
Accelerator Control If the driver continues to press the +RES switch, the system will increase the limit speed in 5 km/h or 5 mph increments. The instant the driver releases the +RES switch, that speed will be rendered as the limit speed.
Tap-up Control If the driver presses the +RES switch momentarily (approximately 0.6 seconds), the system will increase the limit speed by 1 km/h or 1 mph with each press of the switch.
Override Control While driving the vehicle with speed limiter system on, if the driver fully depresses the accelerator pedal, the hybrid vehicle control ECU will detect that the accelerator pedal sensor assembly is in kick down mode. Then, the hybrid vehicle control ECU will recognize this to be the driver's acceleration requirement, and allow the vehicle to accelerate higher than the limit speed. After the acceleration, when the vehicle speed falls below the limit speed, this function will resume limit speed control.
Cancel Control While the vehicle is being driven with the speed limiter system on, if any one of the following signals is input into the hybrid vehicle control ECU, the system will cancel the speed limiter system:
·

CANCEL switch on signal (the driver has pressed the CANCEL switch).

·

Speed limiter switch off signal (deletes the limit speed).

·

Cruise control switch on signal (transfers to the constant speed control mode, turns off the speed limiter indicator, and deletes the limit speed).

·

Malfunction in the hybrid system.

·

When the VSC or TRC system is turned off by pressing the VSC OFF switch.

·

Malfunction in the vehicle speed.

·

Communication malfunction between the skid control ECU and hybrid vehicle control ECU.


Resume Control After turning the CANCEL switch on to turn speed limiter switch off, if the driver pushes the +RES switch, the system will limit the vehicle speed at the limit speed that was set at the time of cancelation.



DIAGNOSIS


a.

In order to make system inspections easier to perform, a diagnosis function is used in consideration of serviceability. The DTCs of malfunctioning parts can be read by connecting the GTS. For details, refer to the Repair Manual.