Home › Engine / Hybrid System › 1KR-FE (ENGINE MECHANICAL) › ENGINE UNIT › from 2020.07
NM36W0E _51 Engine / Hybrid System _091267 1KR-FE ENGINE MECHANICAL _0433012 ENGINE UNIT DE DETAILS F

1KR-FE ENGINE MECHANICAL  ENGINE UNIT  DETAILS  CYLINDER BLOCK  


CONSTRUCTION


a.

An aluminum cylinder block sub-assembly with a 7 mm (0.276 in.) distance between the cylinder bores is used to realize a compact and lightweight configuration.


b.

It is not possible to bore the block with this liner. The liners are the spiny type, which have been manufactured so that their casting exterior forms a large irregular surface in order to enhance the adhesion between the liners and the aluminum cylinder block sub-assembly. The enhanced adhesion helps heat dissipation, resulting in a lower overall temperature and heat deformation of the cylinder bores.

W139433C01
5.833,0.833 6.083,0.417 6.083,0.417 6.25,0.417 true 6.063,1.948 6.25,2.167 6.25,2.167 6.417,2.167 true 4.469,0.271 4.781,0.427 0.313,0.156 10 false *a 6.302,0.313 6.615,0.469 0.313,0.156 10 false *b 6.469,2.063 6.781,2.219 0.313,0.156 10 false *c
*a Cylinder Bore Cross Section *b Cylinder Bore
*c Irregularly Shaped Outer Casting Surface of Liner - -
V100145

Spiny Type Liner - -



c.

Water passages are provided between the cylinder bores. By allowing the engine coolant to flow between the cylinder bores, this construction enables the temperature of the cylinder walls to be kept uniform.


d.

By enlarging the inlet from the engine water pump assembly, coolant inflow resistance is decreased, contributing to improved fuel efficiency.

W139434C01
5.25,2.906 5.667,3.5 5.667,3.5 5.833,3.5 true 4.281,0.229 4.594,0.385 0.313,0.156 10 false *a 4.292,2.042 4.604,2.198 0.313,0.156 10 false *b 5.896,3.396 6.208,3.552 0.313,0.156 10 false *c 2.49,1.219 2.615,1.396 0.125,0.177 10 true A 1.583,1.479 1.708,1.656 0.125,0.177 10 true B 1.573,2.219 1.698,2.396 0.125,0.177 10 true B 1.615,0.625 1.74,0.802 0.125,0.177 10 false A
*a A-A Cross Section *b B-B Cross Section
*c Enlarged Water Passage - -
V100135

Water Passage - -



e.

Through the use of the offset crankshaft, the bore center is shifted 8 mm (0.315 in.) towards the intake, in relation to the crankshaft center. Thus, the side force to cylinder wall is reduced when the maximum pressure is applied, which contributes to fuel economy.

W139435C01
5.156,1.667 5.323,1.667 5.323,1.667 5.792,2.24 true 3.823,1.667 3.99,1.667 3.99,1.667 4.458,2.24 true 2.01,0.333 2.323,0.49 0.313,0.156 10 false *a 3.604,1.583 3.917,1.74 0.313,0.156 10 false *b 5.688,0.375 6,0.531 0.313,0.156 10 false *c 4.51,3.042 4.823,3.198 0.313,0.156 10 false *d 5.813,3.031 6.125,3.188 0.313,0.156 10 false *e 1.969,2.979 2.281,3.135 0.313,0.156 10 false *b 4.938,1.583 5.25,1.74 0.313,0.156 10 false *b 4.479,0.375 4.792,0.531 0.313,0.156 10 false *c
*a Bore Centerline *b Crankshaft Centerline
*c Maximum Pressure *d Offset Crankshaft
*e Non-offset Crankshaft - -