Home › Engine / Hybrid System › 1KR-FE (ENGINE MECHANICAL) › ENGINE UNIT › from 2020.07
NM36W0E _51 Engine / Hybrid System _091267 1KR-FE ENGINE MECHANICAL _0433012 ENGINE UNIT GE GENERAL F

1KR-FE ENGINE MECHANICAL  ENGINE UNIT  GENERAL  GENERAL  


OUTLINE


a.

The 1KR-FE engine is a 1.0-liter, 12-valve DOHC, in-line 3-cylinder gasoline engine.


b.

This engine uses the Direct Ignition System (DIS), Dual Variable Valve Timing-intelligent (Dual VVT-i) system and Electronic Throttle Control System-intelligent (ETCS-i). It has been developed to realize high performance, quietness, fuel economy and clean emission.



SPECIFICATION


Item Specification

*1: Emission regulations differ by country and region.

*2: The figure shown is the weight of the part without coolant and oil.

Engine Type 1KR-FE
No. of Cyls. & Arrangement 3-cylinder, In-line
Valve Mechanism 12-valve DOHC, Chain Drive
(With Dual VVT-i)
Combustion Chamber Pentroof Type
Flow of Intake and Exhaust Gasses Cross-flow
Fuel System Sequential Multiport Fuel Injection (SFI)
Ignition System Direct Ignition System (DIS)
Displacement cm3 (cu. in.) 998 (60.9)
Bore x Stroke mm (in.) 71.0 x 84.0 (2.8 x 3.3)
Compression Ratio 11.8 : 1
Max. Output (EEC) kW@rpm 53@6000
Max. Torque (EEC) N*m@rpm 93@4400
Valve Timing Intake Open 40° to -1° BTDC
Closed 24° to 65° ABDC
Exhaust Open 8° to 53° BBDC
Closed 44° to -1° ATDC
Spark Plug Type DENSO Made FC16HR-Q8
Plug Gap mm (in.) 0.7 to 0.8 (0.0276 to 0.0315)
Firing Order 1 - 2 - 3
Research Octane Number (RON) 95 or higher
Emission Regulation*1 EURO 4
EURO 6d
Engine Service Mass*2 (Reference) kg (lb.) 72.8 (160.5)


MAIN FEATURES


a.

The 1KR-FE engine has achieved the following through the use of the items listed in the table below.

i.

High performance and reliability


ii.

Low noise and vibration


iii.

Lightweight and compact design


iv.

Good serviceability


v.

Clean emissions and improved fuel economy

Item (1) (2) (3) (4) (5)

○: Applicable

-: Not applicable

Engine Proper Cylinder head sub-assembly build-in exhaust manifold is used. ○ - ○ - -
The dual injector system is used. ○ - - - ○
A cylinder block sub-assembly made of aluminum alloy is used. - - ○ - -
Spiny type liners are used. ○ - - - -
An offset crankshaft is used. ○ ○ - - ○
Cylinder block water jacket spacers are used. ○ - - - -
A taper squish shape is used for the top of the pistons. ○ - - - ○
The piston skirt is coated with resin. ○ ○ - - ○
Low-tension piston rings are used. ○ - - - ○
Oil strainer made of plastic is used. - - ○ - -
Valve Mechanism The Dual Variable Valve Timing-intelligent (Dual VVT-i) system is used. ○ - - - ○
A shimless type valve lifters are used. - - ○ - -
A sodium-filled exhaust valve is used. ○ - - - -
A timing chain (chain sub-assembly) and No. 1 chain tensioner assemblies are used. ○ - - ○ -
Intake and Exhaust System An intake manifold made of plastic is used. - - ○ - -
A linkless type throttle body with motor assembly is used. - - ○ ○ -
A stainless steel exhaust manifold is used. - - ○ - -
Fuel System 8-hole type fuel injector assemblies are used. ○ - - - ○
A fuel delivery pipe made of pressed steel is used. - - ○ - -
A fuel returnless system is used. - - ○ ○ ○
A multi-layer plastic fuel tank assembly is used. - - ○ - ○
Quick connectors are used to connect the fuel hoses and fuel pipes. - - - ○ -
Ignition System A Direct Ignition System (DIS) is used. ○ - - ○ ○
Long-reach type iridium-tipped spark plugs are used. ○ - - ○ ○
Engine Control System The Electronic Throttle Control System-intelligent (ETCS-i) is used. ○ - - ○ ○
The flat type knock control sensor is used. ○ - - - -
The vacuum sensor and the intake air temperature sensor are integrated. - - ○ - -