Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
NM36W0E _51 Engine / Hybrid System _091266 1KR-FE ENGINE CONTROL _0433013 SFI SYSTEM CO CONTROL F

1KR-FE ENGINE CONTROL  SFI SYSTEM  CONTROL  ENGINE CONTROL  


FUNCTION OF MAIN COMPONENTS


a.

The main components of the engine control system are as follows:

Component Outline Quantity Function

*1: Models without stop and start system

*2: Models with stop and start system

*3: Models with GPF System

ECM 32-bit CPU 1 The ECM optimally controls the SFI, ESA, and ETCS-i to suit the operating conditions of the engine in accordance with the signals provided by the sensors.
Crank Position Sensor (Rotor Teeth) Pick-up Coil Type (36-2)*1 1 This sensor detects the engine speed and performs cylinder identification.
Hall Type (36-2)*2
Cam Position Sensor (Rotor Teeth) Hall Type (3) 2 This sensor performs cylinder identification.
Knock Control Sensor Built-in Piezoelectric Element Type (Flat Type) 1 This sensor detects an occurrence of the engine knocking indirectly from the vibration of the cylinder block caused by the occurrence of engine knocking.
E.F.I. Vacuum Sensor Assembly Semiconductor Silicon Chip Type 1 This sensor uses built-in semiconductors to detect the intake manifold pressure.
Intake Air Temperature Sensor Thermistor Type 1 This sensor is built into the E.F.I. vacuum sensor assembly.
This sensor detects the intake air temperature by means of an internal thermistor.
Throttle Position Sensor Non-contact Type 1 This sensor detects the throttle valve opening angle.
Heated Oxygen Sensor Planar Type with Heater 2 This sensor detects the oxygen concentration in the exhaust emission by measuring the electromotive force which is generated in the sensor itself.
Accelerator Pedal Sensor Assembly Non-contact Type 1 This sensor detects the amount of pedal effort applied to the accelerator pedal.
Engine Coolant Temperature Sensor Thermistor Type 1 This sensor detects the water temperature by means of an internal thermistor.
Fuel Injector Assembly 8-hole Type 6 The fuel injector is an electromagnetically-operated solenoid with a nozzle which injects fuel in accordance with signals from the ECM.
Differential Pressure Sensor*3 Semiconductor Strain Gauge Type 1 Measures the pressure difference between atmosphere and upstream of the GPF catalyst.



SYSTEM CONTROL


a.

The engine control system has the following features:

System Outline

*1: Models with stop and start system

*2: Models with GPF system

Sequential multiport Fuel Injection (SFI)
·

The D-type SFI system calculates the intake air volume based on the intake manifold pressure signal received from the E.F.I. vacuum sensor assembly and the engine speed.

·

An independent injection system in which fuel is injected once into each cylinder for each 2 revolution of the crankshaft is used.

·

Fuel injection takes 2 forms: Synchronous injection, which always takes place with the same timing in accordance with the basic injection duration and an additional correction based on the signals provided by the sensors. Non-synchronous injection, which takes place at the time an injection request based on the signals provided by the sensors is detected, regardless of the crankshaft position.


Electronic Spark Advance (ESA)
·

Ignition timing is determined by the ECM based on signals from various sensors. The ECM corrects ignition timing in response to engine knocking.

·

This system selects the optimal ignition timing in accordance with the signals received from the sensors and sends the (IGt) ignition signal to the igniter.


Electronic Throttle Control System-intelligent (ETCS-i) Optimally controls the throttle valve opening in accordance with the amount of accelerator pedal effort, the throttle valve opening control request from the ECM, and the condition of the engine and the vehicle.
Dual Variable Valve Timing-intelligent (Dual VVT-i) Regulates operation of the intake and exhaust camshafts to ensure optimal valve timing in accordance with engine operating conditions.
Fuel Pump Control
·

Fuel pump operation is controlled by signals from the ECM.

·

A fuel cut control is used to stop the fuel pump when the airbag is deployed during front or side collision.


Cooling Fan Control Cooling fan operation is controlled by signals from the ECM based on the E.F.I. engine coolant temperature sensor signal.
Early Stage Injection Control*1 The ECM calculates appropriate injection and ignition at an early stage. The ECM uses these calculated values when the engine is stopped due to stop and start system control.
Heated Oxygen Sensor Heater Control Maintains the temperature of the heated oxygen sensor at an appropriate level to increase accuracy of detection of the oxygen concentration in the exhaust gas.
Brake Override System The engine output is restricted when both the accelerator and brake pedals are depressed. (For the Activation Conditions and Inspection Method, refer to the Repair Manual)
Engine Immobiliser Prohibits fuel delivery and ignition if an attempt is made to start the engine with an invalid key.
Air Conditioning Cut-off Control By turning the air conditioning compressor on or off in accordance with engine operating conditions, drivability is maintained.
Gasoline Particulate Filter (GPF) System*2 The ECM regulates the engine operation in accordance with the estimated amount of accumulated particulate matter calculated from increases and decreases in the amount of accumulated particulate matter while the engine is running and by monitoring the differential pressure with the differential pressure sensor.



FAIL-SAFE


a.

When a malfunction of any of the sensors is detected, there is a possibility of an engine or other malfunction occurring if the ECM were to continue normal control. To prevent such a problem, the fail-safe function of the ECM either relies on the data stored in memory to allow the engine control system to continue operating, or stops the engine if a hazard is anticipated. For details, refer to the Repair Manual.



DIAGNOSIS


a.

The ECM also stores Diagnostic Trouble Codes (DTCs) for malfunctions it has detected. The DTCs can be accessed by using the Global TechStream (GTS).


b.

For details, refer to the Repair Manual.