FUNCTION OF MAIN COMPONENTS
| Component | Function | |
|---|---|---|
|
*1: Gasoline Models *2: HV Models with brake booster with master cylinder assembly *3: HV Models with brake master cylinder with motor assembly |
||
| Headlight Assembly LH | Receives headlight control signal and illuminates the high beams and low beams. | |
| Headlight Assembly RH | ||
| Power Distribution Box Assembly | Receives the headlight control signal from the semiconductor power integration ECU and changes between the high beams and low beams. | |
| Semiconductor Power Integration ECU | ||
| Main Body ECU (Multiplex Network Body ECU) | Sends the various signals to the semiconductor power integration ECU. | |
| Automatic Light Control Sensor | Detects the ambient light level and transmits a signal to the main body ECU (multiplex network body ECU). | |
| Front Door Courtesy Light Switch Assembly RH | Detects whether driver's door is open or closed and transmits a signal to the main body ECU (multiplex network body ECU). | |
| Steering Sensor | Sends the light control switch, dimmer switch and auto high beam main switch signals to the main body ECU. | |
| Turn Signal Switch | Light Control Switch | Sends the light control switch signals to the steering sensor. |
| Auto High Beam Switch Assembly | Sends the auto high beam switch signals to the main body ECU. | |
| Central Gateway ECU (Network Gateway ECU) | Relays the signal between the CAN communication lines. | |
| Combination Meter Assembly | ·
Sends the vehicle speed signal to the main body ECU. ·
Illuminates the automatic high beam indicator light to inform the driver when the automatic high beam system is activated. ·
Illuminates the high beam indicator light to inform the driver when the high beams are on. |
|
| Forward Recognition Camera | Determines when to turn the high beams on and off after identifying the lights of oncoming vehicles, preceding vehicles and other lights from the picture information of its camera sensor. Then, the sensor sends high beam request signals to the main body ECU. | |
| Camera Heater (Forward Recognition Hood with Heater Sub-assembly) | The camera heater is heated according to signals from the forward recognition camera. | |
| Air Bag Sensor Assembly | Detects the yaw rate of the vehicle and transmits the signal to main body ECU (multiplex network body ECU). | |
| Brake Actuator Assembly*1,*3
·
Skid Control ECU |
Sends the vehicle speed signal to the combination meter assembly. | |
| Brake Booster with Master Cylinder Assembly*2
·
Skid Control ECU |
||
| ECM*1 | Sends the shift position signals to the combination meter assembly. | |
| Hybrid Vehicle Control ECU*2,*3 | ||
SYSTEM CONTROL
| Function | Operation Condition |
|---|---|
|
*1: Models for Europe *2: Except models for Europe |
|
| Active | When all of the following conditions are met, the automatic high beam system is activated and the automatic high beam indicator light turns on:
·
The ignition switch is ON (IG). ·
The light control switch is in the HEAD or AUTO position and the low beam headlights are on. ·
The dimmer switch is in the low beam position. ·
The auto high beam switch is ON. ·
The shift position is in any position other than R. |
| High Beams On | When all of the following conditions are met, the automatic high beam system turns on the high beams after a short delay:
·
Vehicle speed is more than approximately 40 km/h (25 mph).*1 ·
Vehicle speed is more than approximately 30 km/h (19 mph).*2 ·
The area in front of the vehicle is dark. ·
No oncoming vehicles are present with the headlights on. ·
No preceding vehicles are present with the taillights on. ·
Few streetlights are present along the street ahead. |
| High Beams Off | When any of the following conditions is met, the automatic high beam system turns off the high beams after a short delay:
·
Vehicle speed is less than approximately 30 km/h (19 mph).*1 ·
Vehicle speed is less than approximately 25 km/h (16 mph).*2 ·
The area in front of the vehicle is not dark. ·
An oncoming vehicle with headlights on is detected. ·
A preceding vehicle with taillights on is detected. ·
Several streetlights are present along the street ahead. |
FUNCTION
When passing an oncoming vehicle:
The automatic high beam system turns off the high beams before an oncoming vehicle comes within the detection range.
When an oncoming vehicle passes out of camera sensor range, the automatic high beam system turns the high beams on after a short delay.
| *a | Detection Range | *b | Delay |
| *c | Camera Sensor Angle | - | - |
The detection distance varies depending on detected objects.
The timing of turning on and off the high beams varies depending on the intensity of oncoming (and preceding) vehicle lights.
When passing a preceding vehicle:
When approaching a preceding vehicle, the automatic high beam system turns off the high beams the detection range reaching it.
When a preceding vehicle passes out of camera sensor range, the automatic high beam system turns the high beams on after a short delay.
| *a | Detection Range | *b | Delay |
| *c | Camera Sensor Angle | - | - |
The timing of turning on and off the high beams varies depending on the intensity of the preceding vehicle lights.