FUNCTION OF MAIN COMPONENTS
| Component | Function | ||
|---|---|---|---|
| Brake Booster with Master Cylinder Assembly | Skid Control ECU | ·
Operates the brake actuator assembly and brake actuator to control the brake fluid pressure of each wheel based on signals from each sensor and ECU. ·
Performs regenerative cooperative brake control by communicating with each ECU. |
|
| Master Cylinder | Generates brake fluid pressure in accordance with the depression amount of the brake pedal. | ||
| Stroke Simulator | Generates a natural brake pedal feel in response to depression of the brake pedal by the driver. | ||
| Brake Master Cylinder Reservoir Assembly | Brake Fluid Level Warning Switch | Detects when the brake fluid level is low. | |
| Brake Actuator | Regulator | ·
Supplies pressurized brake fluid which is controlled by the linear solenoid valve to the servo chamber when the skid control ECU is operating. ·
Supplies brake fluid pressure from the accumulator to the servo chamber when the skid control ECU is not operating or during back-up when the skid control ECU is malfunctioning. |
|
| Linear Solenoid Valve (SLA, SLR) | Adjusts the regulator to control the servo pressure as requested. | ||
| Gap Hold Valve (SGH) | ·
During normal control, transmits the brake fluid pressure generated by the depression of the brake pedal by the driver to the stroke simulator. ·
During a malfunction, seals the brake fluid pressure of the gap hold chamber. |
||
| Stroke Simulator Cut Valve (SSA) | Allows the stroke simulator pressure to flow to the brake master cylinder reservoir assembly such as when the system is malfunctioning. | ||
| Relief Valve | Opens to prevent excessive fluid pressure if the pump motor operates continuously such as during a malfunction of the accumulator pressure sensor. | ||
| Accumulator Pressure Sensor (Pacc) | Detects the accumulator brake fluid pressure and is used to control the pump motor. | ||
| Servo Pressure Sensor (Psrv) | Detects the fluid pressure of the servo chamber. | ||
| Stroke Simulator Pressure Sensor (Prct) | Detects the brake fluid pressure in the stroke simulator which is generated by the depression of the brake pedal by the driver. | ||
| Brake Actuator Assembly | Independently controls the brake fluid pressure of the 4 wheels when ABS, TRC, VSC, etc. is operating. | ||
| Brake Booster Pump Assembly | Pump Motor | Pumps the brake fluid from the brake master cylinder reservoir assembly to the accumulator. | |
| Accumulator | Accumulates brake fluid supplied by the pump motor under pressure. | ||
| Speed Sensors | Detect the wheel speed of each of the 4 wheels. | ||
| Airbag Sensor Assembly | Yawrate Sensor | ·
The airbag sensor assembly incorporates the yawrate sensor and acceleration sensor. ·
The yawrate sensor detects the vehicle's yaw rate. ·
The acceleration sensor detects the vehicle's longitudinal and lateral deceleration. ·
The airbag sensor assembly sends the detection signals from the yawrate sensor and acceleration sensor to the skid control ECU via CAN communication. ·
Sends a brake control request signal to the skid control ECU when a collision is detected.*1 |
|
| Acceleration Sensor | |||
| Steering Sensor | Detects the steering direction and angle of the steering wheel. | ||
| Stop Light Switch Assembly | Detects when the brake pedal is depressed. | ||
| Brake Pedal Stroke Sensor Assembly | Detects the stroke distance of the brake pedal. | ||
| Parking Brake Switch Assembly | Outputs the parking brake operation status to the main body ECU (multiplex network body ECU). | ||
| Front Door Courtesy Light Switch Assembly (Driver Side) | Outputs whether the driver door is open or closed to the skid control ECU. | ||
| VSC OFF Switch | Disables TRC and VSC functions when pressed. | ||
| Forward Recognition Camera | Sends brake request signals to the skid control ECU. | ||
| Hybrid Vehicle Control ECU | Controls the regenerative braking force via communication with the skid control ECU during regenerative cooperative braking. Also, controls drive force when TRC or VSC is operating. | ||
| Inverter with Converter Assembly | MG ECU | Sends information regarding the motor to the skid control ECU during regenerative cooperative braking. | |
| ECM | Controls the engine output based on signals received from the hybrid vehicle control ECU. | ||
| Power Steering ECU Assembly | Power Steering ECU | Controls the steering assist torque based on the signals received from the skid control ECU. | |
| Main Body ECU (Multiplex Network Body ECU) | Sends the parking brake status signal to the skid control ECU via CAN communication. | ||
| Central Gateway ECU (Network Gateway ECU) | Relays data between buses. | ||
| Combination Meter Assembly | Each of the lights and buzzers inform the driver of system operations, malfunctions, or control restriction conditions. Also, messages are displayed on the multi-information display in response to system abnormalities and system malfunction. | ||
FAIL-SAFE
If a malfunction is detected in the brake system, the fail-safe function operates. Depending on the type of malfunction, the fail-safe function informs the driver via warning indicators in the combination meter assembly and continues brake control via the use of non-malfunctioning parts. Also, when the system is not operating, the fluid pressure generated in the brake master cylinder by the depression of the brake pedal works as a back-up mechanism to ensure braking force.
DIAGNOSIS
A diagnosis function is provided in consideration of serviceability in order to simplify the inspection of systems. For details of the diagnosis function, refer to the Repair Manual.