Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE CONTROL SYSTEM (for HV Model TMMF Made) › from 2020.07
NM36W0E _54 Brake _088478 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0434644 BRAKE CONTROL SYSTEM(for HV Model TMMF Made) CO CONTROL F

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE CONTROL SYSTEM(for HV Model TMMF Made)  CONTROL  BRAKE CONTROL  


FUNCTION OF MAIN COMPONENTS


Component Function

*: Models with Toyota Safety Sense

Electric Brake Booster (Brake Booster with Master Cylinder Assembly) Brake Booster Control ECU Operates in conjunction with the skid control ECU to control the hydraulic and regenerative brake system.
Motor Rotation Angle Sensor Detects the rotation angle of the motor.
Relative Displacement Sensor Detects the amount of relative displacement caused by depression of the brake pedal and sends it to the brake booster control ECU.
Motor Assists the brake pedal depression force applied by the driver, according to control by the brake booster control ECU.
Brake Master Cylinder Reservoir Assembly Brake Fluid Level Warning Switch Detects when the brake fluid level is low.
Brake Control Power Supply Assembly Supplies power to the electric brake booster (brake booster with master cylinder assembly) when there is a fault in the auxiliary battery.
Brake Actuator Assembly Skid Control ECU
·

Operates in conjunction with the brake booster control ECU to control the hydraulic and regenerative brake system.

·

Judges the vehicle driving condition based on the signals from each ECU, sensor and switch, and sends the brake control signals to the brake actuator.

·

Requests steering torque assist during cooperative control with EPS.


Solenoid Valves Change the fluid path based on the signals from the skid control ECU during the operation of the brake control system functions in order to control the fluid pressure applied to the wheel cylinders.
Pump Motor Drives the pumps inside the brake actuator.
Master Cylinder Pressure Sensor Detects the master cylinder pressure.
Solenoid Relay (Built into Skid Control ECU) Supplies power to the solenoid valves.
Motor Relay (Built into Skid Control ECU) Supplies power to the pump motor.
Speed Sensors Detect the wheel speed of each of the 4 wheels.
Airbag Sensor Assembly Yawrate Sensor
·

The airbag sensor assembly incorporates the yawrate sensor and acceleration sensor.

·

The yawrate sensor detects the vehicle's yaw rate.

·

The acceleration sensor detects the vehicle's longitudinal and lateral deceleration.

·

The airbag sensor assembly sends the detection signals from the yawrate sensor and acceleration sensor to the skid control ECU via CAN communication.

·

Sends a brake control request signal to the skid control ECU when a collision is detected.*1


Acceleration Sensor
Steering Sensor Detects the steering direction and angle of the steering wheel.
Stop Light Switch Assembly Detects when the brake pedal is depressed.
Brake Pedal Stroke Sensor Assembly Directly detects the extent of the brake pedal stroke operated by the driver.
Front Door Courtesy Light Switch Assembly (Driver Side) Outputs whether the driver door is open or closed to the brake booster control ECU.
VSC OFF Switch Disables TRC and VSC functions when pressed.
Forward Recognition Camera* Sends brake request signals to the skid control ECU.
Hybrid Vehicle Control ECU Controls the regenerative braking force via communication with the skid control ECU during regenerative cooperative braking. Also, controls drive force when TRC or VSC is operating.
Inverter with Converter Assembly MG ECU Sends information regarding the motor to the skid control ECU during regenerative cooperative braking.
ECM Controls the engine output based on signals received from the hybrid vehicle control ECU.
Power Steering ECU Assembly Power Steering ECU Controls the steering assist torque based on the signals received from the skid control ECU.
Main Body ECU (Multiplex Network Body ECU) Sends the parking brake status signal to the skid control ECU via CAN communication.
Central Gateway ECU (Network Gateway ECU) Relays data between buses.
Combination Meter Assembly Each of the lights and buzzers inform the driver of system operations, malfunctions, or control restriction conditions. Also, messages are displayed on the multi-information display in response to system abnormalities and system malfunction.


FAIL-SAFE


a.

If a malfunction is detected in the brake system, the fail-safe function operates. Depending on the type of malfunction, the fail-safe function informs the driver via warning indicators in the combination meter assembly and continues brake control via the use of non-malfunctioning parts. Also, when the system is not operating, the fluid pressure generated in the brake master cylinder by the depression of the brake pedal works as a back-up mechanism to ensure braking force.



DIAGNOSIS


a.

A diagnosis function is provided in consideration of serviceability in order to simplify the inspection of systems. For details of the diagnosis function, refer to the Repair Manual.