CONSTRUCTION
A turbocharger sub-assembly integrated into the exhaust manifold is used to achieve high engine output, high torque and low emissions.
A high efficient single-scroll turbocharger is used in the turbocharger sub-assembly to achieve high torque over all ranges from low to high engine speeds.
Ball bearings have been adopted for the turbine bearings to reduce friction.
An abradable seal* has been provided for the surface of the compressor housing, increasing boost efficiency to achieve higher output and higher responsiveness.
*: A coating with excellent machinability characteristics which allows clearances between components to be optimized.
A vacuum type wastegate valve has been adopted for the turbocharger sub-assembly; when driving at low engine speeds and low load, the wastegate valve closes, providing normal boosting for enhanced acceleration response. Furthermore, when driving at high load the wastegate valve may open in some circumstances to protect the engine.
The wastegate valve opens downwards to introduce high temperature gas directly to the Three-Way Catalytic converter (TWC). As a result, TWC warm-up performance during start-up and exhaust gas purification performance are improved.
An electric air bypass valve is used in the turbocharger sub-assembly to prevent the surge phenomenon* from occurring. When the throttle valve closes with the accelerator pedal released, the pressure between the turbocharger sub-assembly and throttle valve increases. This pressure is diverted upstream to the turbocharger sub-assembly when the air bypass valve opens.
* Surge phenomenon: This phenomenon is when the intake airflow reverses. As a result, a noise is generated during deceleration.
| *1 | Turbocharger Sub-assembly | *2 | Actuator |
| *3 | Air Bypass Valve | *4 | Wastegate Valve |
| *5 | Coil | *6 | Shaft |
| *7 | Valve | - | - |
| *a | Opening on Turbine Wheel Side | *b | Air Bypass Valve Cross Section |
|
Exhaust Gas |
|
Intake Air |
OPERATION
Wastegate Valve
When the engine is stopped, the wastegate valve is open.
When the vacuum regulating valve assembly applies a vacuum to the actuator according to signals from the ECM, the actuator closes the wastegate valve through a link.
| *1 | Compressor Wheel | *2 | Turbine Wheel |
| *3 | Wastegate Valve | *4 | Actuator |
| *5 | ECM | *6 | Vacuum Regulating Valve Assembly |
| *7 | Vacuum Pump Assembly | - | - |
| *a | The illustrations shown are examples only. | - | - |
|
Exhaust Gas |
|
Intake Air |
When the vacuum regulating valve assembly cuts the vacuum to the actuator according to signals from the ECM, the actuator opens the wastegate valve through a link.
| *1 | Compressor Wheel | *2 | Turbine Wheel |
| *3 | Wastegate Valve | *4 | Actuator |
| *5 | ECM | *6 | Vacuum Regulating Valve Assembly |
| *7 | Vacuum Pump Assembly | - | - |
| *a | The illustrations shown are examples only. | - | - |
|
Exhaust Gas |
|
Intake Air |
The opening angle of the wastegate valve is determined by the amount of vacuum applied.
Air Bypass Valve
The air bypass valve opens according to signals from the ECM to divert the pressure between the turbocharger sub-assembly and throttle valve, which is increased when the throttle valve is closed, upstream of the turbocharger sub-assembly.
| *1 | ECM | *2 | Air Bypass Valve |
| *3 | Compressor Wheel | *4 | Turbine Wheel |
| *a | To Throttle Body with Throttle Position Sensor Assembly | - | - |
|
Exhaust Gas |
|
Intake Air |
| *1 | ECM | *2 | Air Bypass Valve |
| *3 | Compressor Wheel | *4 | Turbine Wheel |
| *a | To Throttle Body with Throttle Position Sensor Assembly | - | - |
|
Exhaust Gas |
|
Intake Air |