Home › Engine / Hybrid System › G16E-GTS (ENGINE CONTROL) › SFI SYSTEM › from 2020.09
NM36W0E _51 Engine / Hybrid System _095207 G16E-GTS ENGINE CONTROL _0447319 SFI SYSTEM CO CONTROL F

G16E-GTS ENGINE CONTROL  SFI SYSTEM  CONTROL  ENGINE CONTROL  


FUNCTION OF MAIN COMPONENTS


a.

The main components of the engine control system are as follows:

Component Outline Quantity Function

*: Models with GPF

ECM 32-bit CPU 1 Optimally controls the engine control system to suit the operating conditions of the engine in accordance with the signals provided by the sensors.
Air Fuel Ratio Sensor (Bank 1, Sensor 1) Heated Type (Planar Type) 1 Detects the oxygen concentration in the exhaust gas by measuring the electromotive force which is generated in the sensor itself.
No. 2 Air Fuel Ratio Sensor (Bank 1, Sensor 2) Heated Type (Cup Type) 1
Intake Mass Air Flow Meter Sub-assembly Air Flow Meter Silicon Chip Type 1 Uses a built-in silicon chip to directly detect the intake air mass.
Intake Air Temperature Sensor Thermistor Type 1 Detects the intake air temperature.
Engine Coolant Temperature Sensor Thermistor Type 1 Detects the engine coolant temperature.
No. 2 Fuel Pressure Sensor (for Low Pressure) Semiconductor Type 1 Detects the fuel pressure in the fuel delivery pipe (for port injection).
Fuel Pressure Sensor (for High Pressure) Semiconductor Type 1 Detects the fuel pressure in the fuel delivery pipe sub-assembly (for direct injection).
Crank Position Sensor [No. of Rotor Teeth] Magnetic Resistance Element (MRE) Type [36 - 2] 1 Detects the engine speed and performs cylinder identification.
Camshaft Position Sensor [No. of Rotor Teeth] Magnetic Resistance Element (MRE) Type [3] 2 Performs cylinder identification.
Throttle Body with Throttle Position Sensor Assembly Throttle Position Sensor Non-contact Type 1 Detects the throttle valve opening angle.
Throttle Control Motor DC Motor 1 Regulates the opening of the throttle valve in accordance with the signals from the ECM.
E.F.I. Vacuum Sensor Assembly Semiconductor Silicon Chip Type 1 Detects the pressure in the compressor (inlet side) and sends signals to the ECM.
No. 1 Turbo Pressure Sensor Semiconductor Type 1 Detects the turbo pressure.
No. 2 Turbo Pressure Sensor Semiconductor Type 1 Detects the intake manifold pressure.
Accelerator Pedal Rod with Sensor Assembly Non-contact Type 1 Detects the amount of pedal effort applied to the accelerator pedal.
Knock Control Sensor Built-in Piezoelectric Element Type (Flat Type) 1 Detects engine knocking indirectly through the vibration of the cylinder block caused by engine knocking.
Oil Pressure and Temperature Sensor Semiconductor Type 1 Detects the engine oil pressure and the engine oil temperature.
Differential Pressure Sensor* Semiconductor Strain Gauge Type 1 Measures the pressure difference between atmosphere and upstream of the GPF catalyst.
Cam Timing Oil Control Solenoid Assembly Solenoid Type 2 Controls the intake and exhaust camshaft phase to achieve the optimal valve timing by moving the oil control valve.
Port Fuel Injector Assembly 10-hole Type 3 This injector is an electromagnetically-operated nozzle which injects fuel in accordance with signals from the ECM.
Direct Fuel Injector Assembly 6-hole Type 3 This injector contains a high-pressure electromagnetically-operated nozzle used to inject fuel directly into the cylinder.
Ignition Coil Assembly Type with Igniter 3 Incorporates an igniter and provides the high voltage electricity necessary for ignition in accordance with signals from the ECM.
Spark Plug Iridium-tipped Type 3 Produces a spark inside the cylinder using high voltage electricity delivered from the ignition coil assembly
Vacuum Regulating Valve Assembly Solenoid Type 1 Based on signals from the ECM, the wastegate valve is opened and closed.
Air Bypass Valve Solenoid Type 1 Based on signals from the ECM, the air bypass valve is opened and closed.
Vacuum Switching Valve Assembly (for Air Intake Control Valve) Solenoid Type 1 Based on signals from the ECM, the air intake control valve is opened and closed.



SYSTEM CONTROL


a.

The engine control system has the following features:

System Outline
Direct Injection 4-stroke Gasoline Engine Superior Version with Turbo (D-4ST) This system comprehensively controls the D-4S and turbo pressure control.
Direct Injection 4-stroke Gasoline Engine Superior Version Sequential Multiport Fuel Injection (D-4S SFI) System
·

This is an L-type SFI system. It directly detects the intake air mass with a silicon chip type intake mass air flow meter sub-assembly.

·

The D-4S SFI system is a fuel injection system which combines direct injection injectors and port injection injectors.

·

Based on signals from each sensor, the ECM controls the injection volume and timing of each type of injector (direct and port injection types) in accordance with the engine speed and engine load in order to optimize combustion conditions.


Electronic Spark Advance (ESA)
·

Ignition timing is determined by the ECM based on signals from various sensors. The ECM corrects ignition timing in response to engine knocking.

·

This system determines the optimal ignition timing in accordance with the signals received from the sensors and sends ignition (IGt) signals to the igniters.


Electronic Throttle Control System-intelligent (ETCS-i) Optimally controls the opening angle of the throttle valve in accordance with the accelerator pedal input and the engine and vehicle operating conditions.
Dual Variable Valve Timing-intelligent (Dual VVT-i) Regulates operation of the intake and exhaust camshafts to ensure an optimal valve timing in accordance with the engine condition.
Cooling Fan Control The cooling fan ECU steplessly controls the speed of the fan in accordance with the engine coolant temperature, vehicle speed, engine speed, and air conditioning operating conditions. As a result, the cooling performance is improved. For details, refer to the G16E-GTS COOLING section.
Fuel Pump Control (for Low Pressure)
·

Based on signals from the ECM, the fuel pump control ECU controls the fuel pump.

·

The fuel pump is stopped when any of the Supplemental Restraint System (SRS) airbags is deployed in a collision.


Fuel Pump Control (for High Pressure) Regulates the fuel pressure within a range of 2.4 to 22 MPa in accordance with driving conditions.
Air Fuel Ratio Sensor Heater Control Maintains the temperature of the air fuel ratio sensor (bank 1, sensor 1) or No. 2 air fuel ratio sensor (bank 1, sensor 2) at an appropriate level to increase the ability of each sensor to accurately detect the oxygen concentration in the exhaust gas.
Gasoline Particulate Filter (GPF) System Control*1 Monitors the condition of the GPF catalyst.
Turbocharger Control
·

Controls the turbo pressure by opening and closing the wastegate valve in accordance with driving conditions.

·

Prevents the surge phenomenon*2 by opening and closing the air bypass valve in accordance with driving conditions.


Dual Intake System According to driving conditions, the air cleaner assembly intake pathways are switched between 2 stages.
Brake Override System The engine output is restricted when both the accelerator and brake pedals are depressed. (For the Activation Conditions and Inspection Method, refer to the Repair Manual)
Evaporative Emission Control The ECM controls the purge flow of evaporative emissions (HC) from the canister in accordance with the engine operating conditions.
Engine Immobiliser Prohibits fuel delivery and ignition if an attempt is made to start the engine with an invalid key.

HINT:

*1: Models with GPF

*2: Surge phenomenon: This phenomenon is when the intake airflow reverses. As a result, an abnormal noise is easily generated during deceleration.




FAIL-SAFE


a.

When a malfunction of any of the sensors is detected, there is a possibility of an engine or other malfunction occurring if the ECM were to continue normal control. To prevent such a problem, the fail-safe function of the ECM either relies on the data stored in memory to allow the engine control system to continue operating, or stops the engine if a hazard is anticipated. For details, refer to the Repair Manual.



DIAGNOSIS


a.

When the ECM detects a malfunction, the ECM records information related to the fault. Furthermore, the Malfunction Indicator Lamp (MIL) in the combination meter assembly illuminates or blinks to inform the driver.


b.

The ECM also stores Diagnostic Trouble Codes (DTCs) for malfunctions it has detected. The DTCs can be accessed by using the GTS.


c.

For details, refer to the Repair Manual.