Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › from 2020.09
NM36W0E _58 Vehicle Interior _088538 THEFT DETERRENT / KEYLESS ENTRY _0434173 THEFT DETERRENT SYSTEM CO CONTROL F

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  CONTROL  THEFT DETERRENT CONTROL  


SYSTEM CONTROL


a.

The states of the theft deterrent system are as follows:

State Description Theft Detection
Disarmed State The theft deterrent system has not been set by the user. Not possible
Arming Preparation State This is the preparation state before the theft deterrent system becomes active (enters the armed state) when the system has been set by the user. Not possible
Armed State The theft deterrent system is active. (Theft can be detected.) Possible
Alarm Sounding State A theft attempt has been detected and the warning operation activates. Possible

Y264385E01
1.115,1.281 2.5,1.625 1.385,0.344 10 false Disarmed State B 4.292,1.292 5.677,1.635 1.385,0.344 10 false Disarmed State A 4.292,5.302 5.677,5.646 1.385,0.344 10 false Armed State A 1.115,5.302 2.5,5.646 1.385,0.344 10 false Armed State B 1.125,3.396 2.896,3.833 1.771,0.438 10 false Arming Preparation State B 4.292,3.396 6.063,3.833 1.771,0.438 10 false Arming Preparation State A 1.104,7.125 2.969,7.573 1.865,0.448 10 false Alarm Sounding State 1.135,7.479 3,7.927 1.865,0.448 10 false - Vehicle Horn 1.135,7.823 3,8.271 1.865,0.448 10 false - Hazard Warning Light 0.99,6.406 1.948,6.729 0.958,0.323 10 false Condition (11) 2.24,6.396 3.198,6.719 0.958,0.323 10 false Condition (13) 4.25,6.385 5.208,6.708 0.958,0.323 10 false Condition (10) 5.51,6.385 6.469,6.708 0.958,0.323 10 false Condition (12) 6.188,7.688 7.146,8.01 0.958,0.323 10 false Condition (9) 6.146,5.646 7.104,5.969 0.958,0.323 10 false Condition (9) 4.448,4.479 5.406,4.802 0.958,0.323 10 false Condition (7) 1.156,4.49 2.115,4.813 0.958,0.323 10 false Condition (7) 3.198,5.656 4.156,5.979 0.958,0.323 10 false Condition (8) 0.208,5.667 1.167,5.99 0.958,0.323 10 false Condition (9) 3.25,3.427 4.208,3.75 0.958,0.323 10 false Condition (6) 3.24,3.938 4.198,4.26 0.958,0.323 10 false Condition (5) 4.323,2.906 5.281,3.229 0.958,0.323 10 false Condition (3) 5.479,2.896 6.438,3.219 0.958,0.323 10 false Condition (1) 4.25,2.26 5.208,2.583 0.958,0.323 10 false Condition (4) 2.177,2.875 3.135,3.198 0.958,0.323 10 false Condition (3) 1.156,2.115 2.115,2.438 0.958,0.323 10 false Condition (2)


b.

The theft deterrent system activates as shown in the diagram above when one of the items in the table occurs in order to cause the system to enter the respective state.

Condition Item

*1: Models without entry and start system

*2: Models with entry and start system

*3: HV Models

*4: Gasoline Models

*5: Models with Intrusion Sensor

(1) In arming preparation state A, the system state is switched if the following condition is met:
·

IG or ACC is OFF.

·

Engine hood and back door is closed.

·

With all doors and the engine hood closed, all doors are locked by wireless operation*1 or the smart entry and start system*2.


(2) In arming preparation state B, the system state is switched if the following condition is met:
·

From the state where the engine hood or the back door is open, close the engine hood and the back door.


(3) In disarmed state release, the system state is switched if the following condition is met:
·

With all door unlocks of the wireless remote control system*1 or the entry & start system*2 are in operation completed state.

·

Any door is opened.

·

IG or ACC is OFF.

·

The auxiliary battery is reconnected.


(4) In arming preparation state B, the system state is switched if the following condition is met:
·

IG or ACC is OFF.

·

Engine hood and back door is opened.

·

With all doors are closed and all doors are locked with wireless remote control system*1 or entry & start system*2.


(5) In arming preparation state B, the system state is switched if the following condition is met:
·

Engine hood and back door is opened.


(6) In arming preparation state A, the system state is switched if the following condition is met:
·

Engine hood and back door is closed.


(7) In armed state, the system state is switched if the following condition is met:
·

Arming preparation state A or B are Approximately 30 seconds elapse.


(8) In armed state A, the system state is switched if the following condition is met:
·

After the engine hood is opened and the back door is close, close the engine hood for about 1 second or more.

·

After the engine hood is closed and the back door is open, close the back door for about 1 second or more.


(9) In disarmed state, the system state is switched if the following condition is met:
·

IG*4 and READY ON*3 is on.

·

with all door unlocks of the wireless remote control system*1 or the entry & start system are completed*2.


(10) In returns to the armed state A, the system state is switched if the following condition is met:
·

After Approximately 27.5 seconds elapse with the engine hood and back door closed.


(11) In returns to the armed state B, the system state is switched if the following condition is met:
·

After Approximately 27.5 seconds elapse with either or both of the engine hood and backdoor open.


(12) In armed state, the system state is switched if the following condition is met:
·

Engine hood is opened.

·

Back door is opened.

·

Any door is opened.

·

Any door is unlocked.

·

After reconnecting the auxiliary battery, open the engine hood, back door, each door, or unlock any of the doors.

·

The intrusion sensor detects movement within the vehicle.*5

·

The glass breakage sensor detects that glass is broken.*5


HINT:

Ultrasonic waves are used to detect intrusion. Ultrasonic waves do not penetrate steel or glass. When any of the door windows is left open, ultrasonic waves may escape. This may result in the detection of people in the surroundings, leaves or insects entering the vehicle, strong wind or other ultrasonic wave sources in the environment when the vehicle is parked with the door windows open. When parking the vehicle with the door windows open for ventilation, turn off the intrusion sensor using the theft sensor cancel switch.


(13) In armed state, the system state is switched if the following condition is met:
·

With the engine hood open and the back door closed, open the back door.

·

With the engine hood open and the back door closed, open the engine hood.

·

Any door is opened.

·

Any door is unlocked.

·

After reconnecting the auxiliary battery, open the engine hood from closed, open the back door from open, open each door, or unlock any door.

·

The intrusion sensor detects movement within the vehicle.*5

·

The glass breakage sensor detects that glass is broken.*5


HINT:

Ultrasonic waves are used to detect intrusion. Ultrasonic waves do not penetrate steel or glass. When any of the door windows is left open, ultrasonic waves may escape. This may result in the detection of people in the surroundings, leaves or insects entering the vehicle, strong wind or other ultrasonic wave sources in the environment when the vehicle is parked with the door windows open. When parking the vehicle with the door windows open for ventilation, turn off the intrusion sensor using the theft sensor cancel switch.





FUNCTION


a.

The theft deterrent system has the following functions:

Function Outline

*1: Models with entry and start system

*2: Models without entry and start system

Alarm When the theft deterrent system switches to the alarm state, the warning items are operated and the alarm sounds for approximately 27.5 seconds.
Alarm Indicator When the theft deterrent system switches to the armed preparation state or alarm state, the security indicator light is illuminated to inform the user. This indicator is also the immobiliser indicator, which blinks when the immobiliser is in the set state.
Forced Door Lock The main body ECU (multiplex network body ECU) transmits a door lock signal to all the doors when all the following conditions are met:
·

The theft deterrent system is in the alarm state.

·

There is no electrical key transmitter sub-assembly in the actuation area.*1

·

There is no key inserted in the ignition key cylinder.*2

·

One of the doors has been unlocked.


The function stops when one of the following conditions is met:
·

All doors are locked.

·

The warning ends after approximately 27.5 seconds.

·

The electrical key transmitter sub-assembly is in the actuation area.*1

·

The ignition key is inserted in the ignition key cylinder.*2