OUTLINE
A G16E-GTS (1.6 L) engine is used to achieve a higher dimension of balance between fuel efficiency, high performance, clean exhaust gas performance and quietness.
A Direct injection 4-stroke gasoline engine Superior version (D-4S) system (which uses both a direct cylinder injection method and port injection method) is used to perform efficient combustion. In addition, a turbocharger, Electronic Throttle Control System-intelligent (ETCS-i) and Dual Variable Valve Timing-intelligent (Dual VVT-i) system (a continuously variable valve timing mechanism for intake and exhaust) are used to achieve low fuel efficiency, low emissions, high performance and high output.
A Direct injection 4 stroke gasoline engine Superior version with Turbo (D-4ST) that comprehensively performs supercharging control for the turbocharger and Direct injection 4-stroke gasoline engine Superior version (D-4S) system is used. By optimizing the shape of the cylinder head port and piston top surface, it is possible to achieve high tumble flow in addition to high-level supercharged pressure control, improving fuel efficiency and low speed torque.
The shape of the high-efficient intake port, offset crankshaft and combustion chamber is optimized to improve combustion efficiency, and the valve mechanism system is improved to reduce friction loss in each part of the engine. As a result, a high level of engine fuel efficiency is achieved.
SPECIFICATION
| Item | Specification | ||
|---|---|---|---|
| Engine Type | G16E-GTS | ||
| No. of Cyls. & Arrangement | 3-cylinder, In-line | ||
| Valve Mechanism | 12-valve DOHC, Chain Drive
(with Dual VVT-i) |
||
| Combustion Chamber | Pentroof Type | ||
| Flow of Intake and Exhaust Gasses | Cross-flow | ||
| Fuel System | Sequential Multiport Fuel Injection (SFI) D-4ST | ||
| Ignition System | Direct Ignition System (DIS) | ||
| Displacement | 1618 cm3 (98.7 cu. in.) | ||
| Bore x Stroke | 87.5 mm x 89.7 mm (3.44 in. x 3.53 in.) | ||
| Compression Ratio | 10.5 : 1 | ||
| Max. Output (EEC) | Models for Europe | 192 kW @ 6500 rpm | |
| Models for Australia | 200 kW @ 6500 rpm | ||
| Max. Torque (EEC) | Models for Europe | 360 N*m @ 3000 to 4600 rpm | |
| Models for Australia | 370 N*m @ 3000 to 4600 rpm | ||
| Valve Timing | Intake | Open | 50° to 0° BTDC |
| Closed | 10° to 60° ABDC | ||
| Exhaust | Open | 70° to 29° BBDC | |
| Closed | 0° to 41° BTDC | ||
| Spark Plug | Manufacturer | NGK | |
| Type | DILKAR8U7G | ||
| Plug Gap | 0.6 to 0.7 mm (0.0236 to 0.0276 in.) | ||
| Firing Order | 1 - 2 - 3 | ||
| Research Octane Number (RON) | 98 or higher | ||
| Emission Regulation*1 | EURO 6b, EURO 6d | ||
| Engine Service Mass*2 (Reference) | 109 kg (240.3 lb.) | ||
*1: Emission regulations differ by country and region.
*2: The figure shown is the weight of the part without coolant and oil.
MAIN FEATURES
The G16E-GTS engine has achieved the following through the use of the items listed in the table below.
High performance and reliability
Low noise and vibration
Lightweight and compact design
Good serviceability
Clean emissions and improved fuel economy
| Item | i | ii | iii | iv | v | |
|---|---|---|---|---|---|---|
|
○: Applicable -: Not applicable |
||||||
| Engine Proper | An aluminum cylinder block sub-assembly is used. | - | - | ○ | - | - |
| Spiny-type liners are used in the cylinder bores. | ○ | - | - | - | ○ | |
| A piston made of aluminum alloy is used. | - | - | ○ | - | ○ | |
| The piston skirt is coated with resin. | ○ | - | - | - | ○ | |
| An offset crankshaft is used. | ○ | - | - | - | ○ | |
| Bolts with smaller heads than standard bolts of the same thread diameter are used. | ○ | - | ○ | - | - | |
| Valve Mechanism | The Dual Variable Valve Timing-intelligent (Dual VVT-i) system is used for the intake and exhaust camshafts. | ○ | - | - | - | ○ |
| A chain sub-assembly and No. 1 chain tensioner assembly are used. | - | - | ○ | ○ | - | |
| Valve lash adjuster assemblies are used. | ○ | ○ | ○ | ○ | ○ | |
| No. 1 valve rocker arm sub-assemblies are used. | ○ | - | ○ | - | ○ | |
| A sodium-filled exhaust valve is used. | ○ | - | - | - | - | |
| Lubrication System | A cartridge type oil filter sub-assembly is used. | - | - | - | ○ | - |
| Piston oil jets for cooling pistons are used. | ○ | - | - | - | ○ | |
| Cooling System | TOYOTA Genuine Super Long Life Coolant (SLLC) is used. | - | - | - | ○ | - |
| Intake and Exhaust System | An intake manifold made of plastic is used. | ○ | ○ | ○ | - | - |
| A linkless type throttle body with throttle position sensor assembly is used. | ○ | ○ | ○ | ○ | ○ | |
| A turbocharger sub-assembly is used. | ○ | ○ | ○ | - | ○ | |
| The wastegate valve control is used. | ○ | - | - | - | ○ | |
| The air bypass valve control is used. | - | ○ | - | - | - | |
| An air cooled type intercooler assembly is used. | ○ | - | ○ | - | ○ | |
| A dual intake system is used. | ○ | ○ | - | - | - | |
| A stainless steel exhaust pipes are used. | ○ | - | ○ | - | ○ | |
| Emission Control System | An ultra thin-wall, high-cell density ceramic type Three-Way Catalytic converter (TWC) is used. | - | - | - | - | ○ |
| Fuel System | A Direct injection 4-stroke gasoline engine Superior version (D-4S) system is used. | ○ | - | - | - | ○ |
| Quick connectors are used to connect the fuel hoses with the fuel pipes. | - | - | - | ○ | - | |
| 10-hole type low pressure port fuel injector assemblies are used. | ○ | - | - | - | ○ | |
| 6-hole type high pressure direct fuel injector assemblies are used. | ○ | ○ | - | - | ○ | |
| Ignition System | The Direct Ignition System (DIS) is used. | ○ | - | ○ | ○ | ○ |
| Long-reach type iridium-tipped spark plugs are used. | ○ | - | - | ○ | ○ | |
| Serpentine Belt Drive System | A serpentine belt drive system is used. | - | - | ○ | ○ | - |
| Engine Control System | Magnetic Resistance Element (MRE) type camshaft position sensors and crank position sensor are used. | ○ | - | - | - | ○ |
| The Electronic Throttle Control System-intelligent (ETCS-i) is used. | ○ | - | - | - | ○ | |
| An evaporative emission control system is used. | - | - | - | - | ○ | |
Location of small-head bolts