Home › Audio / Visual / Telematics › AUDIO / VIDEO › ACTIVE NOISE CONTROL SYSTEM › from 2020.09
NM36W0E _56 Audio / Visual / Telematics _088596 AUDIO / VIDEO _0448576 ACTIVE NOISE CONTROL SYSTEM CO CONTROL F

AUDIO / VIDEO  ACTIVE NOISE CONTROL SYSTEM  CONTROL  ACTIVE NOISE CONTROL  


FUNCTION OF MAIN COMPONENTS


Component Function

*1: Models with stereo component amplifier assembly

*2: Models without stereo component amplifier assembly

Stereo Component Equalizer Assembly
·

Calculates the frequency of electronic control sounds and engine order component sound based on the vehicle speed, accelerator pedal depression amount, engine speed, generated torque and driving mode signals.

·

Generates the output sound quality based on the calculated frequency information and sends it to the stereo component amplifier assembly.*1

·

Generates the output sound quality based on the calculated frequency information and sends it to the speakers.*2


Active Noise Control Microphone (LH/RH) Detects muffled sounds in the cabin and sends signals to the stereo component equalizer assembly.
Stereo Component Amplifier Assembly*1 Receives signals from stereo component equalizer assembly and transmits these signals to the speakers.
Front No. 1 Speaker Assembly (LH/RH) Generates electronic control sounds and engine order component sound based on signals from the stereo component amplifier assembly*1 or stereo component equalizer assembly*2.
Rear Speaker Assembly (LH/RH)
ECM
·

Outputs engine speed to the stereo component equalizer assembly via the direct line.

·

Sends the information such as the accelerator pedal depression amount, generated torque and drive mode to the stereo component equalizer assembly.


Main Body ECU (Multiplex Network Body ECU)
·

Sends driver seat and front passenger seat power window state signals to the stereo component equalizer assembly.

·

Outputs courtesy light switch signals to the stereo component equalizer assembly.


Brake Actuator Assembly
- Skid Control ECU
Sends vehicle speed signals to the stereo component equalizer assembly.
Central Gateway ECU (Network Gateway ECU) Relays the signal between the CAN communication lines.
DLC3 Can read the Diagnostic Trouble Codes (DTCs) of malfunctions by connecting the GTS.
Radio and Display Receiver Assembly*2 Sends audio signals to the stereo component equalizer assembly.


SYSTEM CONTROL


a.

ANC Function

i.

Based on the muffled sounds in the cabin detected by each active noise microphone and the vehicle condition signals from each ECU, the stereo component equalizer assembly calculates the control signals corresponding to respective speakers in the front No. 1 speaker assembly (RH), front No. 1 speaker assembly (LH), rear speaker assembly (RH) and rear speaker assembly (LH) and then sends the signals to the 4 speakers through the stereo component amplifier assembly.*1


ii.

Based on the muffled sounds in the cabin detected by each active noise microphone and the vehicle condition signals from each ECU, the stereo component equalizer assembly calculates the control signals corresponding to respective speakers in the front No. 1 speaker assembly (RH), front No. 1 speaker assembly (LH), rear speaker assembly (RH) and rear speaker assembly (LH) and then sends the signals to the 4 speakers.*2


iii.

The front No. 1 speaker assembly (RH), front No. 1 speaker assembly (LH), rear speaker assembly (RH) and rear speaker assembly (LH) output electronic control sounds with an inverted phase to the muffled sounds, achieving muffled sound reduction.

HINT:

*1: Models with stereo component amplifier assembly

*2: Models without stereo component amplifier assembly




b.

ESE Function

i.

Based on the vehicle condition signals from each ECU, the stereo component equalizer assembly calculates engine order component sound signals for the speakers in the front No. 1 speaker assembly (RH), front No. 1 speaker assembly (LH), rear speaker assembly (RH) and rear speaker assembly (LH) and then outputs to the 4 speakers through the stereo component amplifier assembly.*1


ii.

Based on the vehicle condition signals from each ECU, the stereo component equalizer assembly calculates engine order component sound signals for the speakers in the front No. 1 speaker assembly (RH), front No. 1 speaker assembly (LH), rear speaker assembly (RH) and rear speaker assembly (LH) and then outputs to the 4 speakers.*2


iii.

The front No. 1 speaker assembly (RH), front No. 1 speaker assembly (LH), rear speaker assembly (RH) and rear speaker assembly (LH) generate engine order component sound to create realistic engine sounds.

HINT:

*1: Models with stereo component amplifier assembly

*2: Models without stereo component amplifier assembly





DIAGNOSIS


a.

If a system malfunction is detected, the stereo component equalizer assembly stores Diagnostic Trouble Codes (DTCs) in its memory. For details, refer to the Repair Manual.