Home › Engine / Hybrid System › CRUISE CONTROL › LANE TRACING ASSIST SYSTEM › from 2020.09
NM36W0E _51 Engine / Hybrid System _087276 CRUISE CONTROL _0417733 LANE TRACING ASSIST SYSTEM CO CONTROL F

CRUISE CONTROL  LANE TRACING ASSIST SYSTEM  CONTROL  LANE TRACING ASSIST CONTROL  


FUNCTION OF MAIN COMPONENTS


Components Function

*1: Models with headup display

*2: Models with steering vibration function

*3: Models with blind spot monitor system

*4: Gasoline models or TMMF made

*5: TMC made HV models only

*6: Gasoline models

*7: HV models

Forward Recognition Camera
·

Captures a view of the road ahead of the vehicle and detects lane markers on the driving lane, and calculates the radius to the center of the lane, lane width, distance from markers and heading angle deviation.

·

Controls the LTA system.

·

Transmits the indicator illumination request signal, multi-information display indication request signal, and buzzer sound request signal to the combination meter assembly.

·

Receives vehicle information and turn signal light operation signals and sends a steering force signal to the power steering ECU assembly.

·

Controls the supply of electric current to the forward recognition hood with heater sub-assembly when the ambient temperature is low.


Forward Recognition Hood with Heater Sub-assembly Control is performed by the forward recognition camera to supply electric current and heat the heater, preventing the windshield glass in front of the forward recognition camera from fogging up.
Millimeter Wave Radar Sensor Assembly Radiates millimeter waves forward, uses the reflected waves to detect the presence of a vehicle traveling ahead and then transmits this information to the forward recognition camera.
Combination Meter Assembly LTA Indicator Illuminates or turns off in accordance with signals from the forward recognition camera.
Multi-information Display Displays a warning message and white lines to inform or warn the driver of the system condition in accordance with signals from the forward recognition camera.
Driving Support System Information Displays white lines to inform the driver of the system condition in accordance with signals from the forward recognition camera.
Buzzer Sounds to warn the driver in accordance with signals from the forward recognition camera.
Steering Pad Switch Assembly LTA Main Switch Detects the on/off status of the LTA system and sends a signal to the forward recognition camera.
Meter Control Switch Sends a customize signal command to the combination meter assembly.
Headup Display (Meter Mirror Sub-assembly)*1 Receives signals from the forward recognition camera in order to display the system conditions.
Turn Signal Switch Sends a turn signal command to the steering sensor.
Power Steering ECU Assembly
·

Controls the power steering motor according to signals from the forward recognition camera.

·

Detects steering operations performed by the driver and outputs the operations to the forward recognition camera.

·

Cancels steering assist when an abnormal torque request signal is received from the forward recognition camera.


Steering Wheel Motor*2 Drives an eccentric motor according to the drive signal from the forward recognition camera received via the combination meter assembly and thereby vibrates the steering wheel.
Blind Spot Monitor Sensor LH/RH*3
·

Projects radar waves from the blind spot monitor sensor to the blind spot monitor detection range to detect the presence of other vehicles, vehicle-to-vehicle distance and relative vehicle speed.

·

Sends the detection information to the forward recognition camera.


Airbag Sensor Assembly Yawrate Sensor Detects yaw rate and transmits a signal to the forward recognition camera.
Steering Sensor Detects the angle and direction of steering and transmits signals to the forward recognition camera.
Brake Actuator Assembly*4 Skid Control ECU Sends a vehicle speed signal from the speed sensor to the forward recognition camera.
Brake Booster with Master Cylinder Assembly*5
ECM*6
·

Sends the shift position signal to the forward recognition camera.

·

Sends the accelerator pedal opening angle signal to the forward recognition camera.


Hybrid Vehicle Control ECU*7
Central Gateway ECU (Network Gateway ECU) Relays and transmits each CAN communication data signal.
Main Body ECU (Multiplex Network Body ECU) Sends country specification information signals to the forward recognition camera.


OPERATION CONDITION


a.

Operating Conditions of Lane Departure Alert Function

Operation Condition
Operating The lane departure alert function is activated when all of the following conditions are met:
·

The LTA main switch is on. (When the LTA main switch is pressed to turn on the LTA system, the LTA indicator illuminates.)

·

The vehicle speed is approximately 50 km/h (32 mph) or more.*1

·

Lane markers or lane boundary are detected.

·

No turn signal command is detected.*2

·

A system malfunction is not detected.


Suspended The lane departure alert function is suspended when any one of the following conditions is met:
·

The vehicle speed is less than approximately 50 km/h (32 mph).*1

·

A turn signal command is detected.*2

·

No lane markers or lane boundary are detected.

·

The yawrate sensor is malfunctioning.

·

The vehicle crosses halfway or further over a lane marker.

·

Detection of the curve radius other than regulated.

·

Detection of the lane width other than regulated.

·

Immediately after the lane departure alert is activated.

·

A malfunction is detected in the LTA system.

·

The temperature of the forward recognition camera is abnormal.


Canceled/Resume The lane departure alert function is stopped when any one of the following conditions is met:
·

The LTA main switch is off.

·

The LTA system is temporarily stopped.

·

The LTA system is malfunctioning.

·

The ignition switch is turned off.


The lane departure alert function resumes when the following conditions are met:
·

The conditions to start operation listed above are satisfied.

·

The LTA system condition returns to normal.

·

The ignition switch is turned off and ON (IG) again to ensure normal operation, after the LTA system has been stopped by a system malfunction.



HINT:

*1: The function operates even if the vehicle speed is less than approximately 50 km/h (32 mph) when the lane centering function is operating.

*2: If it is determined that departing the current lane could cause the vehicle to collide with a vehicle traveling in a neighboring lane, the lane departure alert system operates even while the turn signal lights are flashing. (Models with blind spot monitor system)



b.

Operating Conditions of Steering Assist Function

Operation Condition
Operating The steering assist function is activated when all of the following conditions are met:
·

The LTA main switch is on. (When the LTA main switch is pressed to turn on the LTA system, the LTA indicator illuminates.)

·

The vehicle speed is approximately 50 km/h (32 mph) or more.

·

Lane markers or lane boundary are detected.

·

No turn signal command is detected.*

·

A system malfunction is not detected.

·

Acceleration/deceleration at or above a constant speed is not detected.

·

Steering operations to change the direction of vehicle travel are not performed.

·

Systems related to vehicle safety, such as the VSC and pre-collision system, do not operate.

·

The hands off steering wheel alert is not displayed.


Suspended The steering assist function is suspended when any one of the following conditions is met:
·

The vehicle speed is less than approximately 50 km/h (32 mph).

·

A turn signal command is detected.*

·

No lane markers or lane boundary are detected.

·

The yawrate sensor is malfunctioning.

·

Immediately after the lane departure control function is activated.

·

The vehicle crosses halfway or further over a lane marker.

·

Steering assist generated to change the direction of vehicle travel is detected.

·

If the steering angle speed reaches a certain amount.

·

Acceleration/deceleration at or above a constant speed is detected.

·

Systems related to vehicle safety, such as the VSC and pre-collision system, operate.

·

No steering wheel operation detected.

·

Detection of the curve radius other than regulated.

·

Detection of the lane width other than regulated.

·

A malfunction is detected in the LTA system.

·

The temperature of the forward recognition camera is abnormal.


Canceled/Resume The steering assist function is stopped when any one of the following conditions is met:
·

The LTA main switch is off.

·

The LTA system is temporarily stopped.

·

The LTA system is malfunctioning.

·

The ignition switch is turned off.


The steering assist function resumes when the following conditions are met:
·

The conditions to start operation listed above are satisfied.

·

The LTA system condition returns to normal.

·

The ignition switch is turned off and ON (IG) again to ensure normal operation, after the LTA system has been stopped by a system malfunction.



HINT:

*: If it is determined that departing the current lane could cause the vehicle to collide with a vehicle traveling in a neighboring lane, the lane departure alert system operates even while the turn signal lights are flashing. (Models with blind spot monitor system)



c.

Operating Conditions of Lane Centering Function

Operation Condition
Operating The lane centering function is activated when all of the following conditions are met:
·

The LTA main switch is on. (When the LTA main switch is pressed to turn on the LTA system, the LTA indicator illuminates.)

·

When the system recognizes lane markers or the path of the preceding vehicle.

·

No turn signal command is detected.

·

A system malfunction is not detected.

·

Acceleration/deceleration at or above a constant speed is not detected.

·

Steering operations to change the direction of vehicle travel are not performed.

·

Systems related to vehicle safety, such as the VSC and pre-collision system, do not operate.

·

The hands off steering wheel alert is not displayed.

·

Lane center is turned "On" via customized combination meter assembly settings.

·

Dynamic radar cruise control system (vehicle-to-vehicle distance control mode) is operating.


Suspended The lane centering function is suspended when any one of the following conditions is met:
·

Dynamic radar cruise control system (vehicle-to-vehicle distance control mode) do not operate.

·

A turn signal command is detected.

·

One side of lane markers or the path of the preceding vehicle is not detected.

·

The yawrate sensor is malfunctioning.

·

Steering operations to change the direction of vehicle travel are performed.

·

The vehicle crosses halfway or further over a lane marker.

·

If the steering angle speed reaches a certain amount.

·

Acceleration/deceleration at or above a constant speed is detected.

·

Systems related to vehicle safety, such as the VSC and pre-collision system, operate.

·

No steering wheel operation detected.

·

Detection of the curve radius other than regulated.

·

Detection of the lane width other than regulated.

·

A malfunction is detected in the LTA system.

·

The temperature of the forward recognition camera is abnormal.


Canceled/Resume The lane centering function is stopped when any one of the following conditions is met:
·

The LTA main switch is off.

·

The cruise control switch is off.

·

The LTA system is temporarily stopped.

·

The LTA system is malfunctioning.

·

The ignition switch is turned off.

·

Lane center is turned "Off" via customized combination meter assembly settings.


The lane centering function resumes when the following conditions are met:
·

The conditions to start operation listed above are satisfied.

·

The LTA system condition returns to normal.

·

The ignition switch is turned off and ON (IG) again to ensure normal operation, after the LTA system has been stopped by a system malfunction.

·

Lane center is turned "On" via customized combination meter assembly settings.




d.

Operating Conditions of Vehicle Sway Warning Function

Operation Condition
Operating The vehicle sway warning function is activated when all of the following conditions are met:
·

The vehicle speed is approximately 50 km/h (32 mph) or more.

·

Lane markers are detected.

·

No turn signal command is detected.

·

A system malfunction is not detected.

·

Sway warning is turned "On" via customized combination meter assembly settings.


Suspended The vehicle sway warning function is suspended when any one of the following conditions is met:
·

The vehicle speed is less than approximately 50 km/h (32 mph).

·

A turn signal command is detected.

·

One side of lane markers is not detected.

·

When the steering assist function or lane centering function is running (or immediately after).

·

Detection of the lane width other than regulated.

·

Detection of the curve radius other than regulated.

·

A malfunction is detected in the LTA system.

·

The temperature of the forward recognition camera is abnormal.


Canceled/Resume The vehicle sway warning function is stopped when any one of the following conditions is met:
·

The LTA system is malfunctioning.

·

The ignition switch is turned off.

·

Sway warning is turned "Off" via customized combination meter assembly settings.


The vehicle sway warning function resumes when the following conditions are met:
·

The conditions to start operation listed above are satisfied.

·

The LTA system condition returns to normal.

·

The ignition switch is turned off and ON (IG) again to ensure normal operation, after the LTA system has been stopped by a system malfunction.

·

Sway warning is turned "On" via customized combination meter assembly settings.





SYSTEM CONTROL


a.

Function Overview

i.

Lane Departure Alert Function

·

If the function judges that the vehicle may deviate from the lane or lane boundary it is in, the function illuminates the indicator in the combination meter display and vibrates the steering wheel* or sounds a buzzer so that the driver can take action to avoid lane departure.

*: Models with steering vibration function

Y260070E02
3.938,1.25 4.854,1.448 0.917,0.198 10 false Buzzer 3.938,4.177 4.854,4.375 0.917,0.198 10 false Buzzer 5.052,1.25 5.969,1.448 0.917,0.198 10 false Display 5.052,4.177 5.969,4.375 0.917,0.198 10 false Display 6.198,1.25 7.115,1.448 0.917,0.198 10 false Vibration* 6.198,4.177 7.115,4.375 0.917,0.198 10 false Vibration* 5.021,0.25 5.938,0.448 0.917,0.198 10 false Warning 5.021,3.177 5.938,3.375 0.917,0.198 10 false Warning 0.083,3.75 0.646,4.135 0.563,0.385 10 false Grass, Dirt, etc. 0.083,5.5 2.167,5.75 2.083,0.25 10 false This illustration is an example. 3.677,5.5 7.156,5.75 3.479,0.25 10 false *: Models with Steering Vibration Function

·

If the function judges that departing the current lane could cause a collision with a vehicle traveling in a neighboring lane even when the turn signal lights are on, it provides a warning. (Models with blind spot monitor system)

Y260109E01
3.167,1.885 3.417,0.333 3.417,0.333 3.583,0.333 true 3.656,0.229 4.26,0.583 0.604,0.354 10 false Warning 0.104,3.49 2.135,3.698 2.031,0.208 10 false This illustration is an example.



ii.

Steering Assist Function

·

If the function judges that the vehicle may deviate from the lane or lane boundary it is in, the function performs steering assist to help the driver correct the path of the vehicle. If the driver does not take appropriate action, the function illuminates the indicator in the combination meter display and vibrates the steering wheel* or sounds a buzzer.

*: Models with steering vibration function

Y263082E01
5.031,0.156 6.104,0.354 1.073,0.198 10 false Warning 5.021,2.969 6.094,3.167 1.073,0.198 10 false Warning 3.948,1.188 5.021,1.385 1.073,0.198 10 false Buzzer 5.063,1.188 6.135,1.385 1.073,0.198 10 false Display 6.188,1.188 6.979,1.479 0.792,0.292 10 false Vibration* 5.073,4.01 6.146,4.208 1.073,0.198 10 false Display 3.948,4.01 5.021,4.208 1.073,0.198 10 false Buzzer 6.188,4.01 6.979,4.302 0.792,0.292 10 false Vibration* 0.219,3.917 1.292,4.115 1.073,0.198 10 false Grass, Dirt, etc. 0.906,5.208 2.208,5.49 1.302,0.281 10 false Control output level 0.219,5.75 3,6 2.781,0.25 10 false *: Models with Steering Vibration Function 6.167,4.667 7.156,4.917 0.99,0.25 10 false Steering Assist 6.167,1.792 7.156,2.042 0.99,0.25 10 false Steering Assist 0.219,6.25 2.417,6.5 2.198,0.25 10 false This illustration is an example.

·

If the function judges that departed the current lane could cause a collision with a vehicle traveling in a neighboring lane even when the turn signal lights are on, it provides a warning and performs steering assistance. (Models with blind spot monitor system)

Y260110E01
1.156,2.906 3.563,3.104 2.406,0.198 10 false Steering Assist Function not Operated 1.156,3.188 3.563,3.385 2.406,0.198 10 false Steering Assist Function Operated 5.146,2.896 6.25,3.219 1.104,0.323 10 false Steering Assist 0.115,3.5 2.094,3.698 1.979,0.198 10 false This illustration is an example.



iii.

Lane Centering Function

·

The lane centering function is linked with the dynamic radar cruise control system (vehicle-to-vehicle distance control mode) and provides the required assistance by operating the steering wheel to keep the vehicle in its current lane.*

*: When the dynamic radar cruise control system (vehicle-to-vehicle distance control mode) is not operating, the lane centering function does not operate. If the function detects that the steering wheel has not been operated for a fixed amount of time or the steering wheel is not being firmly gripped, a warning is displayed on the multi-information display and the function is temporarily canceled.

Y260033E01
5.958,1.073 7.01,1.333 1.052,0.26 10 false Steering Assist 0.115,1.885 1.448,2.156 1.333,0.271 10 false Control output level 0.094,2.479 2.24,2.729 2.146,0.25 10 false This illustration is an example.

·

The path of the preceding vehicle is used to help the driver to follow the preceding vehicle, when traffic, etc. makes it difficult or impossible to see lane markers.

Y260034E01
3.333,0.417 3.5,0.417 3.5,0.417 4.094,2.198 true 5.25,0.25 5.417,0.25 5.417,0.25 6.063,1.563 true 1.25,1 1.417,1 1.417,1 1.417,2.167 true 0.083,3.354 2.073,3.635 1.99,0.281 10 false This illustration is an example. 0.406,0.906 1.24,1.188 0.833,0.281 10 false Own Vehicle 1.729,0.313 3.302,0.76 1.573,0.448 10 false Driving Path of Preceding Vehicle 4.073,0.146 5.229,0.385 1.156,0.24 10 false Preceding Vehicle



iv.

Vehicle Sway Warning Function

·

The function detects drift of the vehicle within its lane, which is often the result of a driver who is tired, distracted or not looking ahead, based on the position of the vehicle within its lane and the steering inputs of the driver, to alert the driver.

Y260035E01
4.917,1.531 5.521,1.833 0.604,0.302 10 false Warning 4.396,2.021 4.906,2.354 0.51,0.333 10 false Buzzer 0.094,2.417 2.385,2.677 2.292,0.26 10 false This illustration is an example. 5.448,2.052 5.948,2.375 0.5,0.323 10 false Display

·

The function provides a warning to alert the driver when any of the following conditions occurs.

Y260108E01
0.208,3.417 5.104,3.615 4.896,0.198 10 false This illustration is an example. 4.781,1.958 5.958,2.531 1.177,0.573 10 false Would You Like to Take a Break? 5.115,0.167 5.833,0.458 0.719,0.292 10 false Display 1.813,0.167 3.563,0.479 1.75,0.313 10 false Type of Vehicle Swaying 1.073,1.156 4.063,1.615 2.99,0.458 10 false The vehicle drifts within its lane when the driver is inattentive. 1.083,2.542 3.927,2.99 2.844,0.448 10 false The steering wheel is turned abruptly when the driver is inattentive.





FUNCTION


a.

The LTA system automatically activates each time when the ignition switch is turned ON (IG). The system can be stopped by press and holding the LTA main switch on the steering pad switch assembly. The system can be reactivated by pressing the LTA main switch once again.

Y251557C01
6.01,1.667 6.427,0.833 6.427,0.833 6.594,0.833 true 0.156,0.667 0.469,0.823 0.313,0.156 10 false *a 6.667,0.75 6.979,0.906 0.313,0.156 10 false *b
*a Meter Control Switch *b LTA Main Switch



b.

Lane Tracing Assist System Settings Functions Customization

Item Description Setting

*: Models with steering vibration function

Lane Center Select to enable/disable the lane centering function
·

ON

·

OFF


Alert Warning Method
·

Steering Vibration*

·

Buzzer


Sensitivity Timing of the lane departure alert
·

High

·

Std. (Standard)


Sway Warning Select to enable/disable the vehicle sway warning function
·

ON

·

OFF


Sway Sensitivity Timing of the vehicle sway warning function
·

High

·

Std. (Standard)

·

Low





DIAGNOSIS


a.

In order to make system inspections easier to perform, a diagnosis function is used in consideration of serviceability. The DTCs of malfunctioning parts can be read by connecting the GTS. For details, refer to the Repair Manual.