Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › from 2020.09
NM36W0E _59 Vehicle Exterior _088659 WIPER / WASHER _0422053 WIPER AND WASHER SYSTEM CO CONTROL F

WIPER / WASHER  WIPER AND WASHER SYSTEM  CONTROL  WIPER CONTROL  


FUNCTION OF MAIN COMPONENTS


Front Wiper System
Component Function

*1: Models without rain sensing function (with interval time adjuster function)

*2: Models with rain sensing function

Windshield Wiper Switch Assembly
·

Front Washer Switch

·

Front Wiper Control Switch

·

Interval Time Adjuster*1

·

AUTO Switch*2

·

Rain Sensor Sensitivity Adjuster*2


·

Sets the wiper control switch position, on/off status of the washer switch and interval time adjuster.*1

·

Setting this switch to AUTO will cause the rain sensing function to operate. This switch is also used to adjust the rain sensing function sensitivity.*2


Rain Sensor*2 Senses rain when the AUTO switch (windshield wiper switch assembly) is on, and sends signals to the windshield wiper relay assembly.
Windshield Wiper Motor Assembly Activates the front wipers in accordance with the position signal of the windshield wiper switch assembly via the windshield wiper relay assembly.
Windshield Washer Motor and Pump Assembly Activates in accordance with the signal from the windshield wiper switch assembly via the windshield wiper relay assembly.
Windshield Wiper Relay Assembly Receives the operation signal from the main body ECU (multiplex network body ECU), and inputs it into the windshield wiper motor assembly and windshield washer motor and pump assembly.
Combination Meter Assembly Sends the vehicle speed signal to the main body ECU (multiplex network body ECU).
Main Body ECU (Multiplex Network Body ECU) Receives signals from various sensors and ECUs and sends them to the windshield wiper relay assembly.
Steering Sensor Outputs the position signal of the windshield wiper switch assembly to the main body ECU (multiplex network body ECU).
Central Gateway ECU (Network Gateway ECU) Relays data between buses.

Rear Wiper System (Models with Rear Wiper System)
Component Function
Windshield Wiper Switch Assembly
·

Rear Washer Switch

·

Rear Wiper Control Switch


Outputs the position signal of the windshield wiper switch assembly to the rear wiper motor assembly via the main body ECU (multiplex network body ECU).
Rear Wiper Motor Assembly Activates the rear wipers in accordance with the position signal of the windshield wiper switch assembly via the main body ECU (multiplex network body ECU).
Windshield Washer Motor and Pump Assembly Activates in accordance with the signal from the windshield wiper switch assembly via the windshield wiper relay assembly.
Windshield Wiper Relay Assembly Receives the operation signal from the main body ECU (multiplex network body ECU), and inputs it into the windshield washer motor and pump assembly.
Main Body ECU (Multiplex Network Body ECU) Receives signals from various sensors and ECUs and sends them to the windshield wiper relay assembly and rear wiper motor assembly.
Steering Sensor Outputs the position signal of the windshield wiper switch assembly to the main body ECU (multiplex network body ECU).
Central Gateway ECU (Network Gateway ECU) Relays data between buses.


FUNCTION


a.

Washer-linked Wiper with Drip-prevention Function

i.

When the windshield wiper switch assembly is set to off and the washer switch is turned on more than 0.5 seconds, the wipers start on LO at the same time as the washer fluid is sprayed.


ii.

The wipers operate 3 times on LO after the washer switch is turned off.


iii.

When the washer switch is turned on for approximately 0.5 seconds or more and vehicle speed is approximately 7 km/h (4 mph) or less, as shown in the following diagram, after the end of this operation, the wipers operate once more.

Y137334E01
0.833,0.969 1.75,1.188 0.917,0.219 10 false Wiper Switch 0.833,2 1.844,2.219 1.01,0.219 10 false Washer Motor 0.833,3.198 1.927,3.479 1.094,0.281 10 false Wiper Operation 2.083,0.708 2.396,0.906 0.313,0.198 10 false On 2.083,1.281 2.542,1.479 0.458,0.198 10 false Off 2.76,0.333 4.615,0.667 1.854,0.333 10 false Approximately 0.5 Seconds 2.083,2.302 2.542,2.5 0.458,0.198 10 false Off 2.083,1.76 2.396,1.958 0.313,0.198 10 false On 2.083,3.49 2.542,3.688 0.458,0.198 10 false Off 2.094,2.958 2.406,3.156 0.313,0.198 10 false On 3.365,4 4.281,4.677 0.917,0.677 10 false Washer-linked Operation 4.385,3.833 5.167,4.083 0.781,0.25 10 false 3 Seconds 5.229,4 6.177,4.5 0.948,0.5 10 false Drip-prevention Operation


iv.

Rain Sensing Function (Models with Rain Sensing Function)

·

When the AUTO switch (windshield wiper switch assembly) is on, the rain sensor mounted on the upper area of the windshield detects the amount of rain and the luminance of the surrounding area. When the rain sensor detects rain, it sends an optimal wiper timing signal to the windshield wiper relay assembly in accordance with the vehicle speed, luminance of the surrounding area and the amount of rain detected.

·

The windshield wiper relay assembly changes the operation of the windshield wiper motor assembly as shown in the following table, based on wiper operation request signals sent from the rain sensor. If a wiper HI operation request signal is received due to a sudden increase of the amount of rain, such as a splash on the windshield, the wipers are operated continuously on HI.

·

The rain sensor detects the luminance of the surrounding area. If the luminance changes such as when the vehicle goes in or out of a tunnel, the rain sensor sends a wiper operation request signal in accordance with the situation, enabling the wipers to operate at a comfortable setting.


Wiper Operation
Amount of Rain While Being Driven While Stopped
Large Continuously (at HI) Continuously (at LO)
↓↑ Continuously (at LO) Continuously (at LO)
↓↑ Intermittently at Approximately 0.6 Seconds Interval Intermittently at Approximately 0.8 Seconds Interval
↓↑ Intermittently at Approximately 1.2 Seconds Interval Intermittently at Approximately 1.6 Seconds Interval
↓↑ Intermittently at Approximately 2.1 Seconds Interval Intermittently at Approximately 3.1 Seconds Interval
↓↑ Intermittently at Approximately 3.5 Seconds Interval Intermittently at Approximately 5.4 Seconds Interval
↓↑ Intermittently at Approximately 5.9 Seconds Interval Intermittently at Approximately 9.7 Seconds Interval
↓↑ Intermittently at Approximately 10.1 Seconds Interval Intermittently at Approximately 17.5 Seconds Interval
Small Intermittently at Approximately 17.9 Seconds Interval Intermittently at Approximately 32.7 Seconds Interval
No detection Not operated Not operated


v.

Rain Sensor Sensitivity Adjustment Function (Models with Rain Sensing Function)

·

When the AUTO switch (windshield wiper switch assembly) is on, operating the sensitivity switch adjusts the sensitivity of the rain sensor to adjust the wiper operation timing.



vi.

Vehicle Speed-Sensing, Adjustable Interval Function (Models without Rain Sensing Function)

·

When the windshield wiper control switch (windshield wiper switch assembly) is in the intermittent position, the interval time of the wiper is controlled in 3 stages in accordance with the automatic control adjuster position and the vehicle speed.

·

The interval time can be controlled steplessly within each range.


Y101071E15
3.938,3.333 3.938,3.469 3.938,3.469 5.271,3.469 false 3.802,1.677 3.802,1.531 3.802,1.531 5.073,1.531 false 2.573,4.042 3.781,4.375 1.208,0.333 10 false Vehicle Speed 2.052,2.26 4.438,2.719 2.385,0.458 10 false Interval Time Adjustment Range 0.5,1.802 1.104,2.448 0.604,0.646 10 false Interval Time 5.125,1.448 6.875,2.104 1.75,0.656 10 false Automatic Control Adjuster Position: SLOW 5.365,3.375 7.073,4.052 1.708,0.677 10 false Automatic Control Adjuster Position: FAST 0.865,0.333 1.448,0.615 0.583,0.281 10 false Seconds 1.146,0.615 1.521,0.833 0.375,0.219 10 false 15 1.177,1.594 1.479,1.802 0.302,0.208 10 false 10 1.208,2.552 1.469,2.76 0.26,0.208 10 false 5 1.75,3.635 1.958,3.927 0.208,0.292 10 false 0 4.531,3.677 5.427,3.938 0.896,0.26 10 false km/h (mph) 2.396,3.625 3.135,3.875 0.74,0.25 10 false 20 (12) 3.177,3.646 3.823,3.885 0.646,0.24 10 false 40 (25) 3.958,3.635 4.583,3.938 0.625,0.302 10 false 60 (37)


vii.

Vehicle Speed Switching Function (Models without Rain Sensing Function)

·

When the vehicle stops with the wiper control switch (windshield wiper switch assembly) in the low position, the front wiper operation changes to INT mode automatically.

·

When the wiper control switch (windshield wiper switch assembly) is changed from a position other than low to the low position, the front wiper operates 3 times in LO.


Y109527E04
1.667,2.885 2.5,3.083 0.833,0.198 10 false Not operating 1.885,2.417 2.813,2.74 0.927,0.323 10 false Operating 1.625,0.885 2.583,1.083 0.958,0.198 10 false Other than LO 2.219,0.396 2.542,0.625 0.323,0.229 10 false LO 4.271,3.167 5.281,3.531 1.01,0.365 10 false Operated in LO 2.75,3.167 3.823,3.5 1.073,0.333 10 false Operated in other than LO 5.646,3.167 7,3.594 1.354,0.427 10 false Intermittent operation 4.198,1.729 5.281,2.167 1.083,0.438 10 false Operates 3 times 5.448,1.771 5.75,2.031 0.302,0.26 10 false T1 5.875,1.76 6.177,2.031 0.302,0.271 10 false T1 6.344,1.76 6.677,2.042 0.333,0.281 10 false T1 0.5,2.49 1.583,3 1.083,0.51 10 false Wiper operation 0.188,0.594 1.594,0.792 1.406,0.198 10 false Wiper Control Switch 0.479,3.396 2.427,3.635 1.948,0.24 10 false T1: Approximately 2.5 seconds

·

When the vehicle stops moving and the windshield wiper switch assembly is in the LO position, the wipers operate twice in LO. It then switches to intermittent operation with an interval time of approximately 2.5 seconds. If the vehicle starts moving during this intermittent wiper operation, the wiper automatically returns to LO operation.





FAIL-SAFE


a.

If the windshield wiper switch assembly detects a malfunction during the operation of the rain sensing function, the following controls will be performed:

Trouble Condition
Communication Signal Malfunction If a malfunction occurs in the LIN communication signal, control will continue while preserving the same control status that was in effect before the malfunction occurred.
Rain Sensor Malfunction If a malfunction occurs in the rain sensor, intermittent operation will be conducted in accordance with the position of the automatic control adjuster.
Rain Sensor Temperature Malfunction If the temperature of the rain sensor becomes abnormally high or low, control will be stopped.
Rain Sensor Low Voltage If the voltage of the power source of the rain sensor becomes low, control will continue while preserving the same control status that was in effect before the malfunction occurred.