Home › Drivetrain › GF1A (TRANSFER / 4WD / AWD) › ACTIVE TORQUE SPLIT AWD SYSTEM › from 2020.09
NM36W0E _52 Drivetrain _095690 GF1A TRANSFER / 4WD / AWD _0449377 ACTIVE TORQUE SPLIT AWD SYSTEM CO CONTROL F

GF1A TRANSFER / 4WD / AWD  ACTIVE TORQUE SPLIT AWD SYSTEM  CONTROL  FOUR WHEEL DRIVE CONTROL  


FUNCTION OF MAIN COMPONENTS


Component Function
4WD ECU Assembly Controls the amperage applied to the 4WD linear solenoid based on signals provided by the ECUs, sensors and switches in order to optimally distribute drive torque in accordance with driving conditions.
Transmission Coupling Assembly Distributes drive torque in accordance with the amperage applied by the 4WD ECU assembly.
ECM Outputs signals such as the shift position signal, throttle position signal and engine speed signal to the 4WD ECU assembly.
Brake Actuator Assembly
·

Skid Control ECU


Outputs signals such as the vehicle speed signal and brake pedal depressing signal to the 4WD ECU assembly.
Airbag Sensor Assembly Detects the vehicle's longitudinal and lateral deceleration.
Combination Meter Assembly
·

Multi-information Display


Informs the driver that the 4WD ECU assembly has a malfunction in the system.
Throttle Body with Motor Assembly
·

Throttle Position Sensor


Detects the throttle valve position and outputs it to the ECM.
Crank Position Sensor Detects the engine speed and outputs it to the ECM.
Speed Sensor Detects the wheel speed of each wheel.
Stop Light Switch Assembly Detects the brake pedal depressing signal.
Temperature Sensor Detects the transmission coupling assembly temperature.


SYSTEM CONTROL


a.

Start Off Control

i.

The system ensures start-off performance by optimally distributing engine drive torque to the front and rear wheels.


ii.

To prevent the tight corner braking phenomenon from occurring during low-speed cornering, the system reduces the amount of torque distributed to the rear wheels.

HINT:

*: Tight corner braking phenomenon: a phenomenon in which an AWD vehicle may lurch and decelerate due to a rotational speed difference between the front and rear wheels, such as during low-speed cornering in AWD mode.


X145811C02
1.75,2.344 2.063,2.5 0.313,0.156 10 false *a 5.104,2.344 5.417,2.5 0.313,0.156 10 false *b
*a Straightline Driving *b Low-speed Cornering
V100136

Torque Distribution to Rear Wheels - -




b.

Normal Control

i.

The system uses signals such as the throttle opening angle, engine speed, etc. to calculate the engine output torque, and controls the front/rear wheel driving force distribution according to the AWD mode in order to optimize driving stability, steering responsiveness and acceleration performance.



c.

Cornering Control

i.

When decelerating by braking, AWD control stops in order to maximize the effectiveness of braking control.



d.

VSC Coordinated Control

i.

In situations such as accelerating while cornering on a slippery road surface, the active torque-split AWD system performs coordinated control with the VSC, so that compared to traditional TRC and VSC, smoother acceleration performance and greater stability are achieved.




FUNCTION


a.

AWD Operation Condition Display

i.

The operating conditions of the AWD system in response to driving conditions can be understood even when driving on slippery road surfaces, contributing to a greater feeling of security when driving with the AWD system.


ii.

The AWD operation condition display mode can be displayed or hidden by the driver using the steering switch.

X145814C01
0.281,2.49 0.594,2.646 0.313,0.156 10 false *a
*a The illustrations shown are examples only. - -


·

The distribution of driving force to the front and rear wheels changes according to AWD system operation in response to driving conditions and the AWD mode.

·

The relative intensity of the driving forces applied to the front and rear wheels is displayed by the segments.

·

When the driving force applied to each wheel is large, the number of displayed segments increases, and when it is small, the number of segments decreases.





FAIL-SAFE


a.

When there is a possibility of causing damage to the drivetrain due to a malfunction in the AWD system or rough driving, the system displays the massage on the multi-information display to inform the driver and stops AWD control.

Vehicle Condition Control Combination Meter Assembly
Multi-information Display
AWD system malfunction 2WD driving
(control prohibited)
AWD System
Malfunction
2WD Mode
Engaged
Visit Your Dealer
AWD excess driving (warning before AWD control is prohibited) AWD driving AWD System
Overheated
Switching to
2WD Mode
AWD excess driving 2WD driving
(control prohibited)
AWD System
Overheated
2WD Mode
Engaged


b.

When the message is displayed on the multi-information display, perform the following procedures.

·

Decelerate the vehicle.

·

Stop the vehicle (idle the engine).




c.

When a stable system condition is determined, AWD control automatically resumes.



DIAGNOSIS


a.

The 4WD ECU assembly will also store a Diagnostic Trouble Code (DTC). The DTC can be accessed through the use of a GTS. For details, refer to the Repair Manual.