CONSTRUCTION
The transmission coupling assembly is installed in front of the rear differential, and consists of a control clutch, main clutch, housing, shaft, electromagnetic linear solenoid for engagement of each clutch, armature, cam, ball, and piston.
2 types of clutch are provided, the control clutch and the main clutch. The electromagnetic linear solenoid and the armature are used to control the control clutch, and the engagement of the control clutch operates the cam, ball, and piston to engage the main clutch, in this way, the mechanism retains approximately the same size as the traditional viscous type transmission coupling, while also enabling continuously variable electronic control between AWD and 2WD states.
For the control clutch, a multiple metal plate type is used in order to pass the magnetic flux, for the main clutch, because it needs the ability to transmit large driving forces, a multiple wet plate type is used.
For the control clutch, the outer side is engaged with the housing, and the inner side is engaged with the cam, for the main clutch, the outer side is engaged with the housing, and the inner side is engaged with the shaft.
Drive force from the transfer assembly is passed from the propeller shaft to the housing, and by the engagement of the main clutch, is output from the shaft to the rear differential.
The transmission coupling assembly cannot be disassembled, Replace the transmission coupling assembly as a unit when performing replacement.
The transmission coupling assembly cannot be disassembled. Replace the transmission coupling assembly as a unit when performing replacement. For details, refer to the Repair Manual.
| *1 | Front Housing | *2 | Shaft |
| *3 | Piston | *4 | Armature |
| *5 | Cam | *6 | 4WD Linear Solenoid |
| *7 | Control Clutch | *8 | Main Clutch |
|
Propeller Shaft Side | - | - |
OPERATION
Not Operating
Because the drive current of the electromagnetic linear solenoid is not output, the electromagnetic linear solenoid becomes inoperative, this causes both the control clutch and the main clutch to become disengaged, and driving force is not transmitted.
| *1 | Main Clutch | *2 | Control Clutch |
| *3 | Front Housing | *4 | Piston |
| *5 | Ball | *6 | Armature |
| *7 | Cam | *8 | Electromagnetic Linear Solenoid |
| *9 | Shaft | - | - |
| *a | From the Propeller Shaft | *b | To the Rear Differential Carrier |
| *c | A - A Cross Section | - | - |
Operating
By controlling the amount of drive current output from the 4WD ECU assembly to the electromagnetic linear solenoid, the amount of drive force transmitted to the rear wheels can be controlled via continuously variable control.
When drive current is output from the 4WD ECU assembly, the electromagnetic linear solenoid pulls on the armature, this causes the control clutch to engage, synchronizing the rotation of the housing and cam.
Due to the differential rotation occurring between the cam that is synchronized with the housing and the piston that is engaged with the shaft, the ball works to press open the gap between the cam and piston, this causes the piston to press against the main clutch and thereby cause the main clutch to engage.
With the engagement of the main clutch, drive force is transmitted from the housing to the shaft, and thereby drive force is transmitted from the transfer assembly to the rear wheels.
When the amount of drive current supplied to the electromagnetic linear solenoid is large, the strength of the force applied by the armature to engage the control clutch becomes strong, and the engagement of the control clutch causes the rotation differential occurring between the cam and piston to become larger, this causes the piston to press against the main clutch and thereby cause the main clutch to engage.
| *1 | Main Clutch | *2 | Control Clutch |
| *3 | Front Housing | *4 | Piston |
| *5 | Ball | *6 | Armature |
| *7 | Cam | *8 | Electromagnetic Linear Solenoid |
| *9 | Shaft | - | - |
| *a | From the Propeller Shaft | *b | To the Rear Differential Carrier |
| *c | A - A Cross Section | - | - |
When the amount of drive current supplied to the electromagnetic linear solenoid is small, the strength of the force applied by the armature to engage the control clutch becomes weak, and the slipping of the control clutch causes the rotation differential occurring between the cam and piston to become smaller, this causes the force of the piston pressing against the main clutch to become weaker, thus the engagement force of the main clutch becomes weaker, and so the amount of drive force transmitted by the main clutch becomes smaller.
| *1 | Main Clutch | *2 | Control Clutch |
| *3 | Front Housing | *4 | Piston |
| *5 | Ball | *6 | Armature |
| *7 | Cam | *8 | Electromagnetic Linear Solenoid |
| *9 | Shaft | - | - |
| *a | From the Propeller Shaft | *b | To the Rear Differential Carrier |
| *c | A - A Cross Section | - | - |