Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2020.09
NM36W0E _51 Engine / Hybrid System _091800 STOP AND START _0434050 STOP AND START SYSTEM CO CONTROL F

STOP AND START  STOP AND START SYSTEM  CONTROL  IDLING STOP CONTROL  


FUNCTION OF MAIN COMPONENTS


Component Function

*1: Models with CVT

*2: Models with manual transaxle

*3: Models with G16E-GTS engine

*4: Models with Toyota Safety Sense

*5: Models with stereo component amplifier assembly

Engine Stop and Start ECU Sends either an engine stop or restart signal to the ECM according to the signals from each sensor and switch.
Engine Stop and Start ECU Backup Boost Converter
·

Supplies battery voltage to help make up for the voltage drop that occurs when the engine is restarted, preventing the operation of various systems from being interrupted due to low battery voltage.

·

Supplies battery voltage to the oil pump with motor assembly.


Park/Neutral Position Switch Assembly*1 Detects whether the shift lever position is in park/neutral and sends a signal to the engine stop and start ECU.
Clutch Start Switch Assembly*2 Recognizes that the clutch pedal is depressed and sends a signal to the engine stop and start ECU.
Clutch Switch Assembly*2 Recognizes that the clutch pedal is not depressed and sends a signal to the engine stop and start ECU.
Neutral Position Switch*2 Recognizes that the shift lever is in N and sends a signal to the engine stop and start ECU.
Vacuum Sensor Assembly Detects the brake booster vacuum pressure and sends a signal to the engine stop and start ECU.
Hood Lock Assembly Engine Hood Courtesy Switch Detects whether the hood is open or closed and sends a signal to the engine stop and start ECU.
Front Door Courtesy Light Switch Assembly (Driver) Detects whether the driver door is open or closed and sends a signal to the engine stop and start ECU via the main body ECU (multiplex network body ECU) via CAN communication.
Back Door Lock with Courtesy Light Switch Assembly*3 Detects whether the back door is open or closed and sends a signal to the engine stop and start ECU via the main body ECU (multiplex network body ECU) via CAN communication.
Front Seat Inner Belt Assembly (Driver) Detects whether or not the driver's seat belt has been fastened, and sends a signal to the engine stop and start ECU via the main body ECU (multiplex network body ECU) via CAN communication.
Air Conditioning Amplifier Assembly Sends the outside temperature signal and engine restart signal to the engine stop and start ECU.
Forward Recognition Camera*4 Sends a stop sign recognition signal to the engine stop and start ECU.
Ambient Temperature Sensor (Thermistor Assembly) Sends an outside temperature signal to the combination meter assembly.
Combination Meter Assembly Stop and Start Indicator Light
·

Turns on when the engine is stopped due to stop and start control.

·

Blinks to inform the driver that the idling stop is canceled and the engine will restart when the driver door is opened with the shift lever in P or D during idling stop.*1

·

Informs the driver by sounding the buzzer and blinking the stop and start indicator, of the shift lever being in any position other than N without the clutch pedal depressed. (Changing the shift lever to N will stop sounding the buzzer and flashing the indicator light.)*2


Stop and Start Cancel Indicator Light
·

Turns on to inform the driver that the system has been disabled when stop and start system operation is prohibited by the stop and start cancel switch (combination switch assembly).

·

If a system malfunction is detected, the stop and start cancel indicator light blinks to inform the driver.


Multi-information Display
·

Displays the amount of time idling stop was performed since the ignition switch was turned ON to when the ignition switch was turned off.

·

Displays the settings of the stop and start system or warning information, etc.


Combination Switch Assembly Stop and Start Cancel Switch Operation of the system can be canceled by pressing the stop and start cancel switch (combination switch assembly). Pressing the switch again or turning the power source off and back on restores the operation of the system.
Steering Pad Switch Assembly Sends a multi-information operating signal to the combination meter assembly.
ECM
·

Sends various information about engine conditions to the engine stop and start ECU.

·

Based on signals from the battery state sensor assembly, determines whether the battery installed on the vehicle is a specified or non-specified battery, and sends the determination result to the engine stop and start ECU.


Brake Actuator Assembly Skid Control ECU Sends a vehicle speed signal to the engine stop and start ECU.
Master Cylinder Pressure Sensor Detects brake master fluid pressure from brake master cylinder sub-assembly.
Airbag Sensor Assembly Sends airbag deployment information in the event of a collision and a deceleration signal to the engine stop and start ECU.
Main Body ECU (Multiplex Network Body ECU) Sends a front door courtesy light switch assembly (driver) signal and front seat belt buckle switch (driver) signal to the engine stop and start ECU.
Power Steering ECU Assembly Sends an electrical power steering assist signal to the engine stop and start ECU.
External Backup Boost Converter (Eco-run Vehicle Converter Assembly)*5 Supplements the voltage drop when the engine is stopped to stabilize the audio output.
Battery State Sensor Assembly Detects the battery charging and discharging amount and sends a signal to the ECM.
Stop Light Switch Assembly Detects a brake pedal released condition and sends a signal to the engine stop and start ECU via the ECM.
Accelerator Pedal Sensor Assembly Detects an accelerator pedal opening angle and sends a signal to the engine stop and start ECU via the ECM.
Crank Position Sensor Detects the crankshaft angle when the engine is stopped and sends this information to the ECM.
Oil Pump with Motor Assembly*1 Holds the CVT fluid pressure during idle stop.
CVT Fluid Temperature Sensor (Transmission Wire)*1 Detects the CVT fluid temperature.
Spiral Cable Sub-assembly Steering Sensor Detects the steering direction and angle of the steering wheel.
Engine Coolant Temperature Sensor Sends the coolant temperature to the engine stop and start ECU via the ECM.
Generator Assembly Sends the generator assembly generation condition to the engine stop and start ECU via the ECM.
ST Relay (Starter Relay Assembly) Operates the starter assembly by the on signals from the engine stop and start ECU.
Starter Assembly Starts the engine.
Transmission Control ECU*1 Sends the CVT fluid temperature to the ECM.
Central Gateway ECU (Network Gateway ECU) Transmits signals via the CAN communication bus.


SYSTEM CONTROL


a.

Early Stage Injection Control

i.

Early stage injection control shortens the time it takes the engine to restart after the stop and start system stops the engine, thus allowing smooth initial acceleration.


ii.

The ECM memorizes the crankshaft angle detected by the crank position sensor when the engine is stopped by the stop and start system.


iii.

The ECM judges the injection required and decides which cylinder to ignite when the driver does restart operation. The ECM then uses this information as it starts the engine.

Y188867E10
0.375,0.906 1.75,1.427 1.375,0.521 10 false Engine Stop and Start ECU 3.604,1.094 3.958,1.469 0.354,0.375 10 false ECM 5.24,0.948 7,1.292 1.76,0.344 10 false Fuel Injector Assembly 5.229,1.344 6.833,1.688 1.604,0.344 10 false Ignition Coil Assembly 3.115,2.229 4.948,2.427 1.833,0.198 10 false Crank Position Sensor 0.5,2.49 2.344,2.729 1.844,0.24 10 false : CAN Communication Line



b.

Hill-start Assist Function (Models with CVT)

i.

The driving force (creep phenomenon) of a former CVT vehicle is regulated by depressing the brake pedal while stopped, and the driving force is transmitted by releasing the brake pedal when starting the vehicle. However, when starting a stop and start system equipped vehicle with its engine stopped due to the activation of the idle stop function, there is a short time delay before the driving force is generated as the engine will start after the brake pedal is released.


ii.

The hill-start assist function is a system to assist starting of a stop and start system equipped vehicle on a slope to deal with the situation described above, retaining the brake hydraulic pressure until sufficient driving force is generated.

HINT:
·

The hill-start assist function operates not only on a slope but also on a level surface.

·

Abnormal sounds may be heard, but this does not mean the brake is malfunctioning.

·

The brake pedal response may change or it may vibrate, but this does not mean it is malfunctioning.





c.

System Prohibit Control

i.

For safety, battery protection, comfort and ECU learning reasons, the engine stop and start ECU prohibits stop and start system operation if any one of the following conditions is met.

Prohibition Reason Condition

*1: Models with G16E-GTS engine

*2: If the value learned by the ECU has been cleared by disconnecting the battery or for another reason, stop and start system operation will be prohibited until ECU learning is complete.

Safety If the engine is started with the hood or back door*1 open, such as when jump starting, engine restart operation cannot be ensured. Therefore, stop and start system operation will be prohibited. The operation of the system will be restored on the next trip.
If the driver door or hood is opened before the engine stops, stop and start system operation will be prohibited for safety reasons.
The brake booster vacuum is insufficient.
The driver seat belt is unfastened before the engine stops.
The engine catalyst is being quickly warmed up.
Battery Protection The refresh charge continues for 0.5 to 1 hour, and is carried out approximately every 30 hours of driving. While refresh charge, stop and start system operation will be disabled.
When the idling stop rate becomes higher than the predetermined rate, stop and start system operation will be disabled.
When the battery voltage becomes low and the battery integrated current value becomes the threshold value or less, stop and start operation will be disabled.
Comfort If the air conditioning is on when the outside temperature is high and the evaporator temperature is high, stop and start system operation will be prohibited.
If the air conditioning is on when the outside temperature is low, stop and start system operation will be prohibited.
If the heater is on when the outside temperature is low and the engine coolant temperature is low, stop and start system operation will be prohibited.
If the front DEF switch and blower switch are on, stop and start system operation will be prohibited.
ECU Learning ECU learning is not complete.*2
Operation If the vehicle is stopped while the steering wheel is being operated, stop and start system operation will be prohibited.



d.

Warning Control

i.

While the stop and start system stops the engine, one of following operations warns the driver: sounding the buzzer in combination meter assembly, blinking the stop and start indicator light, displaying the multi-information display in combination meter assembly, or restarting the engine or stopping it from restarting.

Operation Warning Control

*1: Warning buzzer sounds and stop and start indicator blinks are nothing when shift lever in P.

*2: Models with manual transaxle

Hood is opened. The engine stops (mode changes to "stalled", and the engine cannot be restarted until the ignition switch is turned off and then ON).
Driver seat door is opened. The engine starts warning the buzzer sounds, and the stop and start indicator blinks.*1
Shift lever is moved without depressing the clutch pedal.*2 Buzzer sounds and the stop and start indicator light blinks.
Driver seat belt is unfastened. The engine is starts.



e.

Operating Conditions at Engine Stop and Restart

i.

The engine may stop if all of these conditions are detected.

Item Operating Condition

*1: Models with CVT

*2: Models with manual transaxle

*3: When the battery fluid temperature becomes -15°C (5°F) or lower or 75°C (167°F) or higher, control is prohibited. After control is prohibited and the battery fluid temperature rises to -10°C (14°F) or higher or falls to 70°C (158°F) or lower, control is performed.

*4: Regarding Battery Integrated Current

In the stop and start system, the engine stop and start ECU switches the system control mode (stop and start system control permitted/prohibited) based on the battery condition (charge/discharge condition) to protect the battery and to ensure stable engine restarting performance.

The battery charge/discharge condition is determined from the integrated current value calculated from the battery state sensor assembly signal. The integrated current value is obtained by multiplying the current (ampere) detected by the battery state sensor assembly by the time (seconds), and is expressed in the unit A-sec. This can be measured by the GTS.

The engine stop and start ECU determines the power charge based on the integrated current value and prohibits stop and start system control if the value is becomes the threshold or less, because the battery might not be able to start the engine. The threshold varies according to the status of battery charge control.

*5: After the integrated current value becomes -4838 A-sec or less, in order to charge the battery, control is prohibited until the value becomes -3974 A-sec or more.

*6: After the integrated current value becomes -864 A-sec or less, in order to charge the battery, control is prohibited until the value becomes 0 A-sec or more.

*7: After the integrated current value becomes -16434 A-sec or less, in order to charge the battery, control is prohibited until the value becomes -15444 A-sec or more.

*8: After the integrated current value becomes -990 A-sec or less, in order to charge the battery, control is prohibited until the value becomes 0 A-sec or more.

*9: When the engine is restarted, ensure proper braking force so that the vehicle does not advance.

Idle Stop Engine Coolant Temperature 40°C to 105°C (104°F to 221°F)
CVT Oil Temperature*1 25°C to 100°C (77°F to 212°F) (However, once this range has been reached, operation will then be permitted in the range from 22°C to 111°C (72°F to 232°F))
Driver Door Closed
Brake Booster Vacuum Vacuum is within the standard range (on a level surface, more than 42.5 kPa (0.5 kg/cm2, 6.2 psi))
(Changes depending on the brake master cylinder fluid pressure)
Stop and Start Cancel Switch (Combination Switch Assembly) Off condition
Road Gradient*1 -6° to 8°
Vehicle Speed Vehicle speed changes from a constant speed to 0 km/h.
Engine Speed 1250 r/min or less
Shift Lever Position*1 P, D
Shift Lever Position*2 Neutral
Clutch Pedal*2 Released
Drive Mode ECO or NORMAL mode
Driver's Seat Belt 3 seconds or more elapse after the seat belt is fastened.
Engine Hood Closed
Battery Voltage
·

8.5 V or more at engine start. (Models with 1KR-FE engine)

·

8.2 V or more at engine start. (Models with M15A-FKS engine)

·

7.6 V or more at engine start. (Models with G16E-GTS engine)


Battery Fluid Temperature -10°C to 70°C (14°F to 158°F)*3
Battery Integrated Current*4 Except Models with G16E-GTS Engine When the integrated current value meets any of the following conditions:
·

-3974 A-sec or more: Status of Battery Charge Control is Charge Control Coordination Mode, Stop and Start Standalone Mode or Low Temperature Mode.*5

·

0 A-sec or more: Status of Battery Charge Control is Stop and Start Restriction Mode or Temperature High/Low Mode.*6


Models with G16E-GTS Engine When the integrated current value meets any of the following conditions:
·

-15444 A-sec or more: Status of Battery Charge Control is Charge Control Coordination Mode, Stop and Start Standalone Mode, Temperature High/Low Mode or Low Temperature Mode.*7

·

0 A-sec or more: Status of Battery Charge Control is Stop and Start Restriction Mode.*8


Air Conditioning During "cooling down or warming up" or defrost function is not operating.
ECU Learning Completed
Ambient Temperature -5°C (23°F) or more
Steering Operation When the steerage angle speed of the steering wheel is 45 degrees per second or less.
Accelerator Pedal*1 The accelerator pedal is released.
Brake Pedal*9
·

The brake pedal is depressed.

·

The brake master cylinder fluid pressure is 1.1 MPa (11.2 kg/cm2, 160 psi) or higher.

(Changes according to gradient)




ii.

The engine will restart if any of these conditions are detected.

Item Operating Condition

*1: Models with CVT

*2: Models with manual transaxle

Engine Restart Brake Booster Vacuum Insufficient brake booster vacuum
Air Conditioning/Heater When the air conditioning is on and a timer in the air conditioning amplifier assembly completes.
When the automatic blower function is operating and a timer in the air conditioning amplifier assembly completes. Otherwise, a timer in the engine stop and start ECU completes.
The A/C switch or blower switch is turned on.
Evaporator temperature exceeds threshold (threshold varies with temperature, humidity and amount of solar radiator).
Stop and Start Cancel Switch (Combination Switch Assembly) The stop and start cancel switch (combination switch assembly) is turned on.
Battery
·

The battery voltage is 11.4 V or less.

·

The battery integrated current becomes the threshold value or less.


Driver's Door The driver's door is opened.
Driver's Seat Belt The driver's seat belt is unfastened.
Vehicle Speed A vehicle speed signal is input.
Accelerator Pedal*1 The accelerator pedal is depressed.
Brake Pedal*1 The brake pedal is released with the shift lever in D.
Shift Lever*1 Moved from P or D position to another position.
Clutch Pedal*2 The clutch pedal is depressed.
Drive Mode Except ECO or NORMAL mode
Steering Operation The steering wheel turned 25 degrees or more.




FUNCTION


a.

Settings of Stop and Start System

i.

By using the steering pad switch assembly and the multi-information display on the combination meter assembly or by pressing and holding the stop and start cancel switch (combination switch assembly), the engine stop operation time due to stop and start control when the air conditioning system is on can be changed between Standard and Extended (the stop and start system has priority).




DIAGNOSIS


a.

When the engine stop and start ECU detects a malfunction and CAN communication is normal, the engine stop and start ECU records information related to the malfunction. Furthermore, the stop and start indicator light in the combination meter assembly blinks to inform the driver that CAN communication is normal.


b.

The engine stop and start ECU also stores Diagnostic Trouble Codes (DTCs) related to malfunctions. DTCs can be read using the GTS.