Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2020.09
NM36W0E _51 Engine / Hybrid System _091800 STOP AND START _0434050 STOP AND START SYSTEM DE DETAILS F

STOP AND START  STOP AND START SYSTEM  DETAILS  COMBINATION METER  


OPERATION


a.

The combination meter assembly receives the idling on/off signals from the engine stop and start ECU.


b.

The system operation status or warning information is indicated to the driver through the following means:

·

Illuminating or flashing the stop and start indicator light and stop and start cancel indicator light on the combination meter assembly.

·

Sounding a buzzer.

·

Displaying other information on the multi-information display.


Digital Meter
W145977C01
3.125,0.656 3.375,0.24 3.375,0.24 3.542,0.24 true 2.458,0.24 2.625,0.24 2.625,0.24 2.875,0.656 true 3.417,1.667 3.917,2.5 3.917,2.5 4.083,2.5 true 2.26,0.115 2.573,0.271 0.313,0.156 10 false *a 3.604,0.125 3.917,0.281 0.313,0.156 10 false *b 4.156,2.396 4.469,2.552 0.313,0.156 10 false *c 0.188,2.49 0.5,2.646 0.313,0.156 10 false *d
*a Stop and Start Cancel Indicator Light *b Stop and Start Indicator Light
*c Multi-information Display *d The illustrations shown are examples only.


Analog Meter
W145978C01
1.25,2.594 1.417,2.594 1.417,2.594 1.833,1.948 true 2,1.833 2.448,2.583 2.448,2.583 2.615,2.583 true 3.552,1.667 4.104,2.594 4.104,2.594 4.271,2.594 true 1.052,2.479 1.365,2.635 0.313,0.156 10 false *a 2.688,2.479 3,2.635 0.313,0.156 10 false *b 4.344,2.49 4.656,2.646 0.313,0.156 10 false *c 0.177,2.51 0.49,2.667 0.313,0.156 10 false *d
*a Stop and Start Cancel Indicator Light *b Stop and Start Indicator Light
*c Multi-information Display *d The illustrations shown are examples only.


Stop and Start Indicator Light Operation
Item Condition Stop and Start Indicator Light Buzzer

*1: Models with CVT

*2: Models with manual transaxle

System Operating (Engine is stopped) The vehicle is operating normally. Illuminates Does not sound
The driver's door is opened with the shift lever in D.*1 Blinks Sounds
The shift lever is operated without depressing the clutch pedal.*2 Blinks Sounds

Stop and Start Cancel Indicator Light Operation
Condition Stop and Start Cancel Indicator Light

*: The blinking interval is 0.5 seconds.

The vehicle is stopped and system operation conditions are met. Does not illuminate
When the stop and start cancel switch (combination switch assembly) is ON. Illuminates
When any Diagnostic Trouble Code (DTCs) are detected. Blinks*
When the number of times the starter assembly has been operated exceeds the threshold.


c.

Multi-information Display Operation

i.

An indicator and/or messages are displayed on the multi-information display to indicate condition of the stop and start system when certain vehicle conditions are met.

Stop and Start System Condition Multi-information Display Message*1 Vehicle Condition
When the engine cannot be stopped by the stop and start system
V115706

*2
"Press Brake More to Activate" The brake pedal is not depressed enough.
"Non-dedicated Battery" A non-specified battery for the stop and start system may have been installed.
"Battery Charging"
·

The battery charge amount may be low.

·

A refresh charge may be occurring.


"Stop & Start System Unavailable"
·

The engine may have been started with the hood or back door*3 opened.

·

The stop and start system is temporarily disabled.


"In Preparation"
·

The brake booster load decreased.

·

The vehicle is operated at a high elevation.


"For Climate Control"
·

The air conditioning system is being used when the ambient temperature is high or low.

·

Windshield defogger is pressed.


When the engine automatically restarts while stopped by the stop and start system
V115706

*2
"In Preparation" The brake pedal is strongly depressed further or pumped.
"For Climate Control"
·

The air conditioning system is turned on or the air conditioning is being used.

·

Windshield defogger is turned on.


"Battery Charging" The battery charge amount may be low.
When the engine cannot be restarted by the stop and start system*4 - "Stop & Start System Active. Shift to N and Press Clutch to Restart" The shift lever has been shifted from neutral to another position with the clutch pedal released.
The system may be malfunctioning - "Stop & Start System Malfunction. Visit Your Dealer" -

HINT:

*1: Message are listed in the order of priority.

*2: When the engine cannot be stopped by the stop and start system or the engine is restarted while the engine is stopped by the stop and start system, the following mark is displayed on the multi-information display.

*3: Models with G16E-GTS engine

*4: Models with manual transaxle