Home › Engine / Hybrid System › G16E-GTS (STARTING) › STARTING SYSTEM › from 2020.09
NM36W0E _51 Engine / Hybrid System _095828 G16E-GTS STARTING _0449760 STARTING SYSTEM CO CONTROL F

G16E-GTS STARTING  STARTING SYSTEM  CONTROL  STARTER CONTROL (CRANKING HOLD FUNCTION)  


FUNCTION


a.

When the ignition switch is pressed, the certification ECU (smart key ECU assembly) receives a start signal.


b.

When the certification ECU (smart key ECU assembly) detects a start signal (SSW1, SSW2), the certification ECU (smart key ECU assembly) outputs a No. 1 ST relay (starter relay assembly) drive signal (STAR). The No. 1 ST relay (starter relay assembly) activates the starter assembly when it receives this signal. At this time, the certification ECU (smart key ECU assembly) turns off the ACC relay by turning off the power sent from the ACCD terminal. The ACC relay is turned off to prevent flickering of the meter, clock and audio system.


c.

When starting the engine during idling stop control, the engine stop and start ECU sends operation signals to the No. 1 ST relay (starter relay assembly) according to the vehicle condition to operate the starter assembly.


d.

When communication between the certification ECU (smart key ECU assembly) and ECM stops, the certification ECU (smart key ECU assembly) uses the engine speed (NE) signal received from the ECM via a direct line to determine when to turn off the starter.


e.

While cranking, the certification ECU (smart key ECU assembly) continues energizing the No. 1 ST relay (starter relay assembly) until it is determined that the engine has started. When the certification ECU (smart key ECU assembly) has judged that the engine has started, the certification ECU (smart key ECU assembly) stops energizing the No. 1 ST relay (starter relay assembly).


f.

The crank hold time and engine speed when it has been determined that the engine has started successfully are determined according to the engine coolant temperature.


g.

If the engine does not start even though the starter has cranked for 30 seconds, the No. 1 ST relay (starter relay assembly) is turned off to protect the starter motor.

Y251715E01
0.25,0.406 1.073,1.438 0.823,1.031 10 false Ignition Switch (Start Signal) 1.313,0.396 1.625,0.594 0.313,0.198 10 false ON 1.313,0.844 1.625,1.042 0.313,0.198 10 false OFF 1.344,1.479 1.656,1.677 0.313,0.198 10 false ON 1.344,1.927 1.646,2.146 0.302,0.219 10 false OFF 1.344,2.219 1.656,2.417 0.313,0.198 10 false ON 1.333,2.646 1.635,2.865 0.302,0.219 10 false OFF 4.365,3.26 4.667,3.479 0.302,0.219 10 false *2 0.26,1.573 1.406,2.208 1.146,0.635 10 false No. 1 ST Relay 0.323,2.396 1.698,2.594 1.375,0.198 10 false ACC Relay 3.49,1.198 3.792,1.417 0.302,0.219 10 false *1 0.25,3.719 1.219,4.104 0.969,0.385 10 false Engine Speed Signal (NE) 5.833,3.729 6.917,4.125 1.083,0.396 10 false Failed Starting of Engine 0.385,4.594 2.844,4.948 2.458,0.354 10 false *1: Cranking Limit: 30 seconds 0.406,5.052 6.771,5.479 6.365,0.427 10 false *2: The certification ECU (smart key ECU assembly) determines that the engine has started successfully when the engine speed is approximately 1000 rpm.